🇵🇱 Politechnika Świętokrzyska PL

PCA AP 240 • Kielce, Poland • 9 calibration items

Metrology & calibration

Politechnika Świętokrzyska is a calibration laboratory accredited by PCA under number AP 240 (Kielce, Poland). Its accreditation scope covers 9 calibration items in the following areas: Metrology & calibration. Calibrated items include: 90° two-arm squares, Internal cylinders, Laser distance meters, Magnification standards. Most frequently used calibration principles: Internal procedure; At permanent location (S), At permanent location (S).

At a glance

  • Accreditation number: PCA AP 240
  • Calibration items in scope: 9
  • Types of calibrated items: 9
  • Calibration principles used: 2
  • City: Kielce, Poland
  • Valid until: 22-06-2030
Accreditation number
AP 240
Accreditation body
PCA
Address
Al. Tysiąclecia Państwa Polskiego 7, 25-314 Kielce
City
Kielce, Poland
Division
INTERLAB Advanced Measurement Techniques Laboratory
Valid until
22-06-2030

What this laboratory calibrates (9)

Calibration principles (2)

Certificate information

Issue date
23.06.2026
Issue no.
1
Certificate date
23.06.2026
Accreditation cycle
23.06.2026 — 22.06.2030
Approved by
Katarzyna Wiśniewska

Accreditation scope — calibration items (9)

The uncertainty covered by the CMC is the expanded uncertainty with a coverage probability of approximately 95 %. The CMC uncertainty is expressed in measurand units. A CMC uncertainty value given as the equation Q[a; b] represents the square root of the sum of the squares of the terms in brackets: Q[a; b] = (a² + b²)^1/2.

No. Calibrated quantity / subject of calibration Nominal range / parameters / CMC Calibration principle Calibration procedure
Calibration items
1 Internal cylinders Calibration — Length
100 mm to 1000 mm · CMC Q[4; 3 ·D] µm; D – measured value (m)
Length
Internal procedure; At permanent location (S) IW3_PL
2 Laser distance meters Calibration — Length
500 mm to 12000 mm · CMC 0,7 mm
Length
Internal procedure; At permanent location (S) IW1_PG
3 Total stations Calibration — Length
500 mm to 12000 mm · CMC 0,3 mm
Length
Internal procedure; At permanent location (S) IW1_PG
4 90° two-arm squares Calibration — Angle
up to 1000 mm · CMC 1,0”
Angle
Internal procedure; At permanent location (S) IW2_PL
5 Roughness measurement standards type A Calibration — Length (surface geometry)
Pt — 0,1 µm to 15 µm · CMC 60 nm
Length (surface geometry)
At permanent location (S) PN-EN ISO 5436-1:2002
6 Roughness measurement standards type B1 Calibration — Length (surface geometry)
Ra — 0, 5 µm to 15 µm · CMC Q[15; 25 · Ra] nm; Ra – measured value (µm)
Length (surface geometry)
At permanent location (S) PN-EN ISO 21920-2:2022-06 PN-EN ISO 21920-3:2022-06
7 Roughness measurement standards type C Calibration — Length (surface geometry)
Ra, Rq — 0,05 µm to 15 µm · CMC Q[15; 25 · Ra] nm; Ra – measured value (µm) Rz, Rt, Rp, Rv — up to 1000 µm · CMC [40; 50 · Rp] nm; Rp – measured value (µm)
Length (surface geometry)
At permanent location (S) PN-EN ISO 21920-2:2022-06 PN-EN ISO 21920-3:2022-06
8 Roughness measurement standards type D Calibration — Length (surface geometry)
Ra, Rq — 0,05 µm to 15 µm · CMC Q[15; 25 · Ra] nm; Ra – measured value (µm) Rz, Rt, Rp, Rv, Rmax — up to 1000 µm · CMC [40; 60 · Rp] nm; Rp – measured value (µm)
Length (surface geometry)
At permanent location (S) PN-EN ISO 21920-2:2022-06 PN-EN ISO 21920-3:2022-06
9 Magnification standards Calibration — Length (surface geometry)
Pt — up to 15 µm · CMC 200 nm
Length (surface geometry)
Internal procedure; At permanent location (S) IW1_PL

Reference standards (7)

IW1_PG
IW1_PL
IW2_PL
IW3_PL
PN-EN ISO 21920-2:2022-06
PN-EN ISO 21920-3:2022-06
PN-EN ISO 5436-1:2002

The same scope as data (JSON): https://labcoda.pl/api/accreditation-scopes/labs/PL/AP%20240