🇵🇱 Meas-Lab Sp. z o.o. PL

PCA AP 220 • Bestwina, Poland • 24 calibration items

Metrology & calibration

Meas-Lab Sp. z o.o. is a calibration laboratory accredited by PCA under number AP 220 (Bestwina, Poland). Its accreditation scope covers 24 calibration items in the following areas: Metrology & calibration. Calibrated items include: Measuring projectors, Spatial reference objects, Special gauges, Surface plates. Most frequently used calibration principles: Internal procedure; Direct method; At permanent location (S) and ou…, Internal procedure; At permanent location (S) and outside of it (P), Internal procedure; Direct method Calibration using a coordinate me….

At a glance

  • Accreditation number: PCA AP 220
  • Calibration items in scope: 24
  • Types of calibrated items: 24
  • Calibration principles used: 8
  • City: Bestwina, Poland
  • Valid until: 23-11-2027
Accreditation number
AP 220
Accreditation body
PCA
Address
ul. Bialska 30, 43-512 Bestwina
City
Bestwina, Poland
Division
Meas-Lab Calibration Laboratory
Valid until
23-11-2027

What this laboratory calibrates (24)

Calibration principles (8)

Certificate information

Issue date
06.03.2026
Issue no.
4
Certificate date
06.03.2026
Accreditation cycle
24.11.2023 — 23.11.2027
Approved by
Katarzyna Wiśniewska

Accreditation scope — calibration items (24)

The uncertainty covered by the CMC is the expanded uncertainty with a coverage probability of approximately 95 % and is expressed in measurand units. A CMC uncertainty value expressed as the equation Q[a; b] denotes the root sum of squares of the terms in brackets: Q[a; b] = (a² + b²)^1/2.

No. Calibrated quantity / subject of calibration Nominal range / parameters / CMC Calibration principle Calibration procedure
Calibration items
1 Vertical Abbe length measuring machines Calibration — Length
0 mm to 100 mm · CMC (0,11 + 2 · L) µm
Length
Internal procedure; Direct method; At permanent location (S) and outside of it (P) PW-1
2 Horizontal Abbe length measuring machines Calibration — Length
0 mm to 100 mm · CMC (0,11 + 2 · L) µm 100 mm to 1000 mm · CMC (0,1 + 3,4 · L) µm
Length
Internal procedure; Direct method; At permanent location (S) and outside of it (P) PW-1
3 Horizontal length measuring machines (1-D machines) Calibration — Length
0 mm to 100 mm · CMC (0,11 + 2 · L) µm 100 mm to 1000 mm · CMC (0,1 + 3,4 · L) µm 1000 mm to 1900 mm · CMC (0,3 + 3,4 · L) µm 1900 mm to 2700 mm · CMC (0,6 + 3,4 · L) µm
Length
Internal procedure; Direct method; At permanent location (S) and outside of it (P) PW-1
4 Universal measuring microscopes
Workshop measuring microscopes
Calibration — Length
0 mm to 25 mm · CMC (0,25 + 1 · L) µm 25 mm do 1000 mm · CMC (0,3 + 3 · L) µm 1000 mm do 2000 mm · CMC (1,0 + 2,6 · L) µm 2000 mm do 3000 mm · CMC (4,3 + 2,6 · L) µm
Length
Internal procedure; Direct method; At permanent location (S) and outside of it (P) PW-1
5 Measuring projectors Calibration — Length
0 mm to 600 mm · CMC (0,3 + 3 · L) µm
Length
Internal procedure; Direct method; At permanent location (S) and outside of it (P) PW-1
6 Digital height gauges with resolution Calibration — Length
- 0.01 mm — 0 mm to 1000 mm · CMC (6 + 1 · L) µm - 0.001 mm — 0 mm to 1000 mm · CMC (0,7 + 2,2 · L) µm - 0.0005 mm — 0 mm to 1000 mm · CMC (0,3 + 2,6 · L) µm - 0.0001 mm — 0 mm to 1000 mm · CMC (0,3 + 2,6 · L) µm
Length
Internal procedure; Direct method; At permanent location (S) and outside of it (P) PW-1
7 Vernier height gauges Calibration — Length
0 mm to 400 mm · CMC 29 µm
Length
Internal procedure; Direct method; At permanent location (S) and outside of it (P) PW-1
8 Line scales Calibration — Length
0 mm to 1000 mm · CMC (0,5 + 4 · L)
Length
Internal procedure; Substitution method Calibration using a coordinate measuring machine and a reference line scale; At permanent location (S) PW-6
9 Line scales of measuring magnifiers Calibration — Length
0 mm to 25 mm · CMC (0,25 + 1 · L) µm
Length
Internal procedure; Direct method; At permanent location (S) and outside of it (P) PW-1
10 Setting standards for internal dimensions Calibration — Length
0 mm to 1410 mm · CMC (0,7 + 2 · L) µm
Length
Internal procedure; Direct method Calibration using a coordinate measuring machine; At permanent location (S) PW-3
11 Setting standards for external dimensions Calibration — Length
0 mm to 1410 mm · CMC (0,7 + 2 · L) µm
Length
Internal procedure; Direct method Calibration using a coordinate measuring machine; At permanent location (S) PW-3
12 Measuring projectors Calibration — Angle
0° to 360° · CMC 2′
Angle
Internal procedure; Direct method; At permanent location (S) and outside of it (P) PW-1
13 Universal measuring microscopes
Workshop measuring microscopes
Calibration — Angle
0° to 360° · CMC 2′
Angle
Internal procedure; Direct method; At permanent location (S) and outside of it (P) PW-1
14 Surface plates Calibration — Length (surface geometry)
(100 x 100) mm to (630 x 630) mm · CMC 1,9 µm
Length (surface geometry)
Internal procedure; Direct method Calibration using a coordinate machine; At permanent location (S) PW-4 based on PN-ISO 8512-1:1998, PN-ISO 8512-2:1999
15 Surface plates Calibration — Length (surface geometry)
(250 x 250) mm to (1000 x 1000) mm · CMC (1 + 0,2 · L) µm (800 x 1200) mm to (2000 x 3000) mm · CMC (0,3 + 0,9 · L) µm
Length (surface geometry)
Internal procedure; Direct method Calibration using electronic levels; At permanent location (S) and outside of it (P) PW-4 based on PN-ISO 8512-1:1998, PN-ISO 8512-2:1999
16 Contact probes
Touch-trigger contact probes
Scanning contact probes
Calibration — Length (coordinate measurements)
0 mm to 25 mm · CMC 0,1 µm
Length (coordinate measurements)
Internal procedure; At permanent location (S) and outside of it (P) PW-2 based on PN-EN ISO 10360-4:2002, PN-EN ISO 10360-5:2020-10
17 Optical coordinate measuring machines with an imaging probe Calibration — Length (coordinate measurements)
0 mm to 606 mm · CMC Q[0,25; 2,2 L) µm 606 mm to 1515 mm · CMC (0,15 + 2,1 · L) µm
Length (coordinate measurements)
Internal procedure; At permanent location (S) and outside of it (P) PW-2 based on PN-EN ISO 10360-7:2011
18 Optical coordinate measuring microscopes Calibration — Length (coordinate measurements)
0 mm to 606 mm · CMC Q[0,25; 2,2 L) µm 606 mm to 1515 mm · CMC (0,15 + 2,1 · L) µm
Length (coordinate measurements)
Internal procedure; At permanent location (S) and outside of it (P) PW-2 based on PN-EN ISO 10360-7:2011
19 Optical coordinate measuring projectors Calibration — Length (coordinate measurements)
0 mm to 606 mm · CMC Q[0,25; 2,2 L) µm 606 mm to 1515 mm · CMC (0,15 + 2,1 · L) µm
Length (coordinate measurements)
Internal procedure; At permanent location (S) and outside of it (P) PW-2 based on PN-EN ISO 10360-7:2011
20 Spatial reference objects
Special gauges
Calibration — Length (coordinate measurements)
0 mm do 1410 mm · CMC (0,7 + 2 · L) µm 0° to 360° · CMC 20″
Length (coordinate measurements)
Internal procedure; Direct method - length - diameter - angle - form, orientation, location and run-out deviations Calibration and measurement using a coordinate measuring machine; At permanent location (S) PW-3
21 Spatial reference objects
Special gauges
Calibration — Length (coordinate measurements)
0 mm do 3000 mm · CMC 100 µm 0° to 360° · CMC 30′
Length (coordinate measurements)
Internal procedure; Direct method - length - diameter - angle - form, orientation, location and run-out deviations Calibration and measurement using a coordinate measuring arm; At permanent location (S) and outside of it (P) PW-3
22 Coordinate measuring machines Calibration — Length (coordinate measurements)
0 mm to 1530 mm · CMC (0,1 + 1,4 · L) µm 1530 mm to 4090 mm · CMC (0,15 + 1,4 · L) µm
Length (coordinate measurements)
Internal procedure; At permanent location (S) and outside of it (P) PW-2 based on PN-EN ISO 10360-2:2010
23 Articulated arm coordinate measuring machines Calibration — Length (coordinate measurements)
0 mm to 4090 mm · CMC (0,5 + 1,4 · L) µm
Length (coordinate measurements)
Internal procedure; At permanent location (S) and outside of it (P) PW-2 based on ASME B89.4.22:2004, PN-EN ISO 10360-12:2017
24 Coordinate measuring systems Calibration — Length (coordinate measurements)
0 mm to 1000 mm · CMC (2 + 1 · L) µm
Length (coordinate measurements)
Internal procedure; At permanent location (S) and outside of it (P) PW-2 based on VDI/VDE 2634 Blat 2 2012, VDI/VDE 2634 Blat 3 2008

Reference standards (15)

ASME B89.4.22:2004
PN-EN ISO 10360-12:2017
PN-EN ISO 10360-2:2010
PN-EN ISO 10360-4:2002
PN-EN ISO 10360-5:2020-10
PN-EN ISO 10360-7:2011
PN-ISO 8512-1:1998
PN-ISO 8512-2:1999
PW-1
PW-2
PW-3
PW-4
PW-6
VDI/VDE 2634 Blat 2 2012
VDI/VDE 2634 Blat 3 2008

The same scope as data (JSON): https://labcoda.pl/api/accreditation-scopes/labs/PL/AP%20220