🇵🇱 Mitutoyo Polska Sp. z o.o. PL

PCA AP 197 • Wrocław, Poland • 8 calibration items

Metrology & calibration

Mitutoyo Polska Sp. z o.o. is a calibration laboratory accredited by PCA under number AP 197 (Wrocław, Poland). Its accreditation scope covers 8 calibration items in the following areas: Metrology & calibration. Calibrated items include: Contact profilometers, Contact scanning probing systems, Contact touch-trigger probing systems, Contourographs. Most frequently used calibration principles: Outside of permanent location (P), Internal procedure; Outside of permanent location (P).

At a glance

  • Accreditation number: PCA AP 197
  • Calibration items in scope: 8
  • Types of calibrated items: 8
  • Calibration principles used: 2
  • City: Wrocław, Poland
  • Valid until: 16-08-2029
Accreditation number
AP 197
Accreditation body
PCA
Address
ul. Skrzypowa 1, 54-530 Wrocław
City
Wrocław, Poland
Division
Mitutoyo Polska Sp. z o.o. Service
Valid until
16-08-2029

What this laboratory calibrates (8)

Calibration principles (2)

Certificate information

Issue date
13.08.2025
Issue no.
5
Certificate date
30.06.2025
Accreditation cycle
13.08.2025 — 16.08.2029
Approved by
Katarzyna Wiśniewska

Accreditation scope — calibration items (8)

The uncertainty covered by the CMC is the expanded uncertainty with a coverage probability of approximately 95 % and is expressed in measurand units.

No. Calibrated quantity / subject of calibration Nominal range / parameters / CMC Calibration principle Calibration procedure
Calibration items
1 Contourographs Calibration — Length (surface geometry)
GX0 — 0 mm to 200 mm · CMC (0,1 + 0,035 · L) µm GXZ45 — 0 mm to 60 mm · CMC 1,1 µm EX1 — 0 mm to 200 mm · CMC (0,6 + 1,4 · L) µm EZ1 — 0 mm to 60 mm · CMC (0,2 + 1,1 · L) µm - angle — 90° to 135° · CMC 0,003°
Length (surface geometry)
Internal procedure; Outside of permanent location (P) PO_14_I01_S
2 Contact profilometers Calibration — Length (surface geometry)
Ra — 0,1 µm to 0,4 µm · CMC (0,012 + 0,050 · Ra) µm Ra — 1 µm to 3 µm · CMC (0,017 + 0,030 · Ra) µm Rz — 1 µm to 12 µm · CMC (0,089 + 0,030 · Rz) µm Rzmax — 1 µm to 12 µm · CMC (0,128 + 0,030 · Rzmax) µm Pt — 0 µm to 8 µm · CMC 0,01 µm EZ1 — 0 µm to 760 µm · CMC 0,10 µm
Length (surface geometry)
Internal procedure; Outside of permanent location (P) PO_14_I01_S based on standard PN-EN-ISO-12179:2022-06E
3 Form deviation measuring instruments Calibration — Length (surface geometry)
- roundness — 0 µm to 1,6 µm · CMC 0,011 µm - flatness — 0 µm to 1,6 µm · CMC 0,011 µm - straightness X — 0 µm to 8 µm · CMC 0,012 µm - straightness Z2 — 0 µm to 8 µm · CMC 0,016 µm - parallelism Z2 — 0 µm to 16 µm · CMC 0,083 µm - cylindricity — 0 µm to 8 µm · CMC 0,1 µm - inclination — 0 µm to 8 µm · CMC 0,012 µm
Length (surface geometry)
Internal procedure; Outside of permanent location (P) PO_14_I02_S based on standard PN-EN ISO 5463:2025-03E
4 Optical probing systems Calibration — Length (coordinate measurements)
0,1 mm to 26 mm · CMC 0,2 µm
Length (coordinate measurements)
Outside of permanent location (P) PN-EN ISO 10360-7:2011
5 Contact touch-trigger probing systems Calibration — Length (coordinate measurements)
25 mm · CMC 0,2 µm
Length (coordinate measurements)
Outside of permanent location (P) PN-EN ISO 10360-5:2020-10
6 Contact scanning probing systems Calibration — Length (coordinate measurements)
25 mm · CMC 0,3 µm
Length (coordinate measurements)
Outside of permanent location (P) PN-EN ISO 10360-5:2020-10
7 Optical coordinate measuring machines with an imaging probing system Calibration — Length (coordinate measurements)
10 mm to 900 mm · CMC (0,1 + 1,0 · L) µm
Length (coordinate measurements)
Outside of permanent location (P) PN-EN ISO 10360-7:2011
8 Coordinate measuring machines Calibration — Length (coordinate measurements)
- with a laser interferometer — 10 mm to 5000 mm · CMC (0,1 + 0,3 · L) µm - with a step gauge — 10 mm to 1510 mm · CMC (0,3 + 0,4 · L) µm
Length (coordinate measurements)
Outside of permanent location (P) PN-EN ISO 10360-2:2010

Reference standards (7)

PN-EN ISO 10360-2:2010
PN-EN ISO 10360-5:2020-10
PN-EN ISO 10360-7:2011
PN-EN ISO 5463:2025-03E
PN-EN-ISO-12179:2022-06E
PO_14_I01_S
PO_14_I02_S

The same scope as data (JSON): https://labcoda.pl/api/accreditation-scopes/labs/PL/AP%20197