🇵🇱 ITA Spółka z ograniczoną odpowiedzialnością Sp. k. PL

PCA AP 181 • Poznań, Poland • 14 calibration items

Metrology & calibration

ITA Spółka z ograniczoną odpowiedzialnością Sp. k. is a calibration laboratory accredited by PCA under number AP 181 (Poznań, Poland). Its accreditation scope covers 14 calibration items in the following areas: Metrology & calibration. Calibrated items include: - for compressive forces, - for tensile forces, Contour measuring instruments - contourographs, Coordinate Measuring Systems (CMS). Most frequently used calibration principles: Internal procedure; Outside of permanent location (P), Internal procedure; At permanent location (S) and outside of it (P), Internal procedure; At permanent location (S).

At a glance

  • Accreditation number: PCA AP 181
  • Calibration items in scope: 14
  • Types of calibrated items: 21
  • Calibration principles used: 7
  • City: Poznań, Poland
  • Valid until: 12-03-2030
Accreditation number
AP 181
Accreditation body
PCA
Address
Skórzewo, ul. Poznańska 104, 60-185 Poznań
City
Poznań, Poland
Division
ITA Calibration Laboratory
Valid until
12-03-2030

What this laboratory calibrates (21)

Calibration principles (7)

Certificate information

Issue date
24.04.2026
Issue no.
12
Certificate date
20.12.2019
Accreditation cycle
17.02.2026 — 12.03.2030
Approved by
Katarzyna Wiśniewska

Accreditation scope — calibration items (14)

The uncertainty covered by the CMC is the expanded uncertainty with a coverage probability of approximately 95 % and is expressed in measurand units. A CMC uncertainty value expressed as a percentage is the relative measurement uncertainty and refers to the percentage of the value of the measurand.

No. Calibrated quantity / subject of calibration Nominal range / parameters / CMC Calibration principle Calibration procedure
Calibration items
1 Reference foils Calibration — Length
3,5 µm to 800 µm · CMC 0,51 µm 0,8 mm to 25 mm · CMC (0,7 + 1,8 · L) µm
Length
Internal procedure; using a dial gauge instrument or a dial gauge instrument; At permanent location (S) ITA-LW-IT-5.4.8-01 based on PN-ISO 4593:1999
2 Coating thickness gauges Calibration — Length
0 mm to 1200 µm · CMC (0,7 + 2 · 10⁻³ · L) µm 1,2 mm to 7,5 mm · CMC 0,4 %
Length
Internal procedure; using a reference foil; At permanent location (S) and outside of it (P) ITA-LW-IT-5.4.11-01
3 Contour measuring instruments - contourographs Calibration — Angle
0° to 180° · CMC 4"
Angle
Internal procedure; Outside of permanent location (P) ITA-LW-IT-5.4.9-01
4 Contact profilometers Calibration — Length (surface geometry)
Pt: 0 µm to 75 µm · CMC 0,03 µm Ra: 0,13 µm to 3,2 µm · CMC U of the standard + 1 % Ra Rz: 1 µm to 10 µm · CMC U of the standard + 1 % Rz Rmax (Rt): 1,13 µm to 10 µm · CMC U of the standard + 1 % Rmax (Rt)
Length (surface geometry)
Internal procedure; At permanent location (S) and outside of it (P) ITA-LW-IT-5.4.7-01 based on PN-EN ISO 12179:2022-06
5 Coordinate Measuring Systems (CMS) with an optical distance sensor
Coordinate optical scanners
Calibration — Length (coordinate measurements)
60 mm to 1480 mm · CMC (1,25 + 1,25 · L) µm
Length (coordinate measurements)
Internal procedure; At permanent location (S) and outside of it (P) ITA-LW-IT-5.4.3-01 based on PN-EN ISO 10360-8:2014
6 Coordinate Measuring Systems (CMS)
Optical scanners for rotationally symmetric parts
Calibration — Length (coordinate measurements)
diameter: — 2 mm to 345 mm · CMC (0,3 + 0,6 · L) µm length: — 4 mm to 1200 mm · CMC (0,6 + 0,7 · L) µm diameter: — 12 mm to 78 mm · CMC (0,6 + 0,6 · L) µm length: — 9 mm to 297 mm · CMC (0,8 + 0,6 · L) µm
Length (coordinate measurements)
Internal procedure; using length and diameter standards; Outside of permanent location (P) ITA-LW-IT-5.4.2-01
7 Contour measuring instruments - contourographs Calibration — Length (coordinate measurements)
- for ceramic standards — 0 mm to 75 mm · CMC diameter: 1,1 µm straightness: 0,03 µm distance: 0,08 µm - for steel standards — 0 mm to 75 mm · CMC (0,05 + 0,95 · L) µm
Length (coordinate measurements)
Internal procedure; Outside of permanent location (P) ITA-LW-IT-5.4.9-01
8 Coordinate Measuring Systems (CMS)
Optical coordinate measuring machines with an imaging probing system
Optical coordinate measuring microscopes with an imaging probing system
Optical coordinate measuring microscopes
Optical coordinate measuring projectors
Calibration — Length (coordinate measurements)
0,10 mm to 750 mm · CMC (0,5 + 0,33 · L) µm
Length (coordinate measurements)
Internal procedure; using line standards; Outside of permanent location (P) ITA-LW-IT-5.4.5-01
9 Static testing machines
- for tensile forces
- for compressive forces
Calibration — Force
with weights — 0,01 N to 110 N · CMC 0,1 % with class 00 and 05 control force transducers — 10 N to 250 kN · CMC 0,12 %
Force
Internal procedure; Outside of permanent location (P) ITA-LW-IT-5.4.1-01 based on PN-EN ISO 7500-1:2018, ASTM E4-24
10 Technological devices
- for tensile forces
- for compressive forces
Calibration — Force
with weights — 0,01 N to 110 N · CMC 0,1 % with class 00 and 05 control force transducers — 10 N to 250 kN · CMC 0,12 %
Force
Internal procedure; At permanent location (S) and outside of it (P) ITA-LW-IT-5.4.1-04 based on PN-EN ISO 7500-1:2018
11 Extensometers Calibration — Force
0 mm to 1300 mm · CMC 0,15 % (not less than 0,5 μm)
Force
Internal procedure; Outside of permanent location (P) ITA-LW-IT-5.4.6-01 based on PN-EN ISO 9513:2013-06, ASTM E2309/E2309M-20, ASTM E83-25
12 Static testing machines
Technological devices
- crosshead displacement speed
Calibration — Force
0 mm/min to 2500 mm/min · CMC 0,2 %
Force
Internal procedure; Outside of permanent location (P) ITA-LW-IT-5.4.10-01 based on ASTM E2658-15R23
13 Torque transducers
Torque meters
Calibration — Torque
0,01 Nm to 20 Nm · CMC 0,2 %
Torque
Internal procedure; At permanent location (S) and outside of it (P) ITA-LW-IT-5.4.4-01
14 Shore durometers Calibration — Hardness
- force for Shore A, AO, B, O, E scale — 550 mN to 8050 mN · CMC 15 mN - force for Shore D, C, DO scale — 0 mN to 44550 mN · CMC 41 mN - force for Shore OO, OOO scale — 203 mN to 1111 mN · CMC 3,5 mN - force for Shore AM, M scale — 324 mN to 764 mN · CMC 3,5 mN - diameter: of the indenter, of the presser foot hole, of the presser foot, of the indenter cone — 0 mm to 30 mm · CMC 2,6 µm - indenter tip radius — 0 mm to 8 mm · CMC 2,6 µm - area — 200 mm² to 1000 mm² · CMC 5 µm² - indenter cone angle — 29°30' to 35°30' · CMC 2,2' - indenter displacement — 0,00 mm to 2,60 mm · CMC 3 µm - indenter length — 0,00 mm to 2,60 mm · CMC 2,6 µm
Hardness
Internal procedure; At permanent location (S) ITA-LW-IT-5.4.13-01 based on ISO 48-9:2018, ASTM D 2240-15R21

Reference standards (24)

ASTM D 2240-15R21
ASTM E2309/E2309M-20
ASTM E2658-15R23
ASTM E4-24
ASTM E83-25
ISO 48-9:2018
ITA-LW-IT-5.4.1-01
ITA-LW-IT-5.4.1-04
ITA-LW-IT-5.4.10-01
ITA-LW-IT-5.4.11-01
ITA-LW-IT-5.4.13-01
ITA-LW-IT-5.4.2-01
ITA-LW-IT-5.4.3-01
ITA-LW-IT-5.4.4-01
ITA-LW-IT-5.4.5-01
ITA-LW-IT-5.4.6-01
ITA-LW-IT-5.4.7-01
ITA-LW-IT-5.4.8-01
ITA-LW-IT-5.4.9-01
PN-EN ISO 10360-8:2014
PN-EN ISO 12179:2022-06
PN-EN ISO 7500-1:2018
PN-EN ISO 9513:2013-06
PN-ISO 4593:1999

The same scope as data (JSON): https://labcoda.pl/api/accreditation-scopes/labs/PL/AP%20181