🇵🇱 SFERATIC Sp. z o.o. PL

PCA AP 180 • Gdynia, Poland • 56 calibration items

Metrology & calibration

SFERATIC Sp. z o.o. is a calibration laboratory accredited by PCA under number AP 180 (Gdynia, Poland). Its accreditation scope covers 56 calibration items in the following areas: Metrology & calibration. Calibrated items include: Analogue dial gauges with a scale interval of:, Digital dial gauges with a resolution of:, Ultrasonic thickness gauges, 90° squares. Most frequently used calibration principles: Internal procedure; Direct method using gauge blocks; At permanent…, Internal procedure; Direct method using a horizontal length measuri…, Internal procedure; At permanent location (S).

At a glance

  • Accreditation number: PCA AP 180
  • Calibration items in scope: 56
  • Types of calibrated items: 57
  • Calibration principles used: 20
  • City: Gdynia, Poland
  • Valid until: 22-01-2030
Accreditation number
AP 180
Accreditation body
PCA
Address
ul. Kadłubowców 4, 81-336 Gdynia
City
Gdynia, Poland
Division
Calibration Laboratory
Valid until
22-01-2030

What this laboratory calibrates (57)

Calibration principles (20)

Certificate information

Issue date
12.10.2026
Issue no.
20
Certificate date
13.09.2022
Accreditation cycle
22.12.2025 — 22.01.2030
Approved by
Katarzyna Wiśniewska

Accreditation scope — calibration items (56)

The uncertainty covered by the CMC is the expanded uncertainty with a coverage probability of approximately 95 % and is expressed in measurand units. A CMC uncertainty value expressed as a percentage is the relative measurement uncertainty and refers to the percentage of the value of the measurand.

No. Calibrated quantity / subject of calibration Nominal range / parameters / CMC Calibration principle Calibration procedure
Calibration items
1 Lever-type analogue dial gauges with a scale interval of: Calibration — Length
0,01 mm; 0,001 mm; 0,002 mm — 0 mm to 3 mm · CMC 3,1 µm
Length
Internal procedure; Direct method using a micrometer head; At permanent location (S) Internal procedure PP TENSLAB/CZ/5/24
2 Analogue dial gauges with a scale interval of: Calibration — Length
0,1 mm — 0 mm to 50 mm · CMC 7 µm 0,01 mm — 0 mm to 50 mm · CMC 3 µm 0,001 mm — 0 mm to 50 mm · CMC 3 µm
Length
Internal procedure; Direct method using a micrometer head; At permanent location (S) Internal procedure PP TENSLAB/CZ/5/24
3 Analogue dial gauges with a scale interval of: Calibration — Length
0,1 mm — 0 mm to 100 mm · CMC 17 µm 0,01 mm — 0 mm to 100 mm · CMC 3 µm 0,001 mm — 0 mm to 100 mm · CMC 3 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/PCZ/1/25
4 Digital dial gauges with a resolution of: Calibration — Length
0,01 mm — 0 mm to 50 mm · CMC 7 µm 0,001 mm — 0 mm to 50 mm · CMC 4 µm
Length
Internal procedure; Direct method using a micrometer head; At permanent location (S) Internal procedure PP TENSLAB/CZ/5/24
5 Digital dial gauges with a resolution of: Calibration — Length
0,01 mm — 0 mm to 100 mm · CMC 17 µm 0,001 mm — 0 mm to 100 mm · CMC 3 µm 0,0005 mm — 0 mm to 100 mm · CMC 3 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/PCZ/1/25
6 Reference foils Calibration — Length
0 mm to 1,5 mm · CMC 4,3 µm 1,5 mm to 5 mm · CMC 8,0 µm 5 mm to 10 mm · CMC 16 µm 10 mm to 15 mm · CMC 24 µm 15 mm to 20 mm · CMC 32 µm 20 mm to 25 mm · CMC 40 µm
Length
Internal procedure; Direct method using a horizontal length measuring machine; At permanent location (S) Internal procedure PP TENSLAB/WZ.GR/2/25
7 Dial depth gauges Calibration — Length
0 mm to 100 mm · CMC 3 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/PCZ/1/25
8 Micrometer depth gauges Calibration — Length
0 mm to 200 mm · CMC 1 + 10 · L µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/GŁ/3/18
9 Vernier depth gauges Calibration — Length
0 mm to 150 mm · CMC 20 µm 0 mm to 300 mm · CMC 27 µm 0 mm to 400 mm · CMC 28 µm 0 mm to 500 mm · CMC 30 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/GŁ/3/18
10 Dial thickness gauges Calibration — Length
0 mm to 100 mm · CMC 3 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/PCZ/1/25
11 Ultrasonic thickness gauges Calibration — Length
3 mm to 48 mm · CMC 0,03 mm
Length
Internal procedure; Direct method using a step wedge; At permanent location (S) Internal procedure PP TENSLAB/UMG/2/19
12 Gauge block comparators Calibration — Length
0 mm to 100 mm · CMC 30 nm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) and outside of it (P) Internal procedure PP TENSLAB/KOMP/1/22 based on EURAMET cg-2 Version 2.1 (02/2023)
13 Dial calipers for internal measurements Calibration — Length
0 mm to 100 mm · CMC 4 µm 100 mm to 150 mm · CMC 5 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/PCZ/1/25
14 Dial calipers for external measurements Calibration — Length
0 mm to 50 mm · CMC 3 µm 50 mm do 150 mm · CMC 4 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/PCZ/1/25
15 Internal micrometers Calibration — Length
5 mm to 50 mm · CMC 3,0 µm 50 mm to 150 mm · CMC 3,2 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/PMwew/1/19
16 Coating thickness gauges Calibration — Length
0 µm to 300 µm · CMC 2,1 µm 300 µm to 1000 µm · CMC 4,1 µm
Length
Internal procedure; Direct method using reference foils; At permanent location (S) Internal procedure PP TENSLAB/MGR/2/24
17 External micrometers Calibration — Length
0 mm to 1000 mm · CMC 1 + 10 · L µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/MIKR.ZEW/5/18
18 Gauge blocks of class (0, 1, 2) Calibration — Length
0,5 mm to 100 mm · CMC 0,08 + 0,4 · L µm
Length
Comparison method using a two-probe comparator; At permanent location (S) PN-EN ISO 3650:2000
19 Rigid rules
Semi-rigid rules
Calibration — Length
0 m to 3 m · CMC 0,148 + 0,0022 · L mm
Length
Internal procedure; Comparison method using a rigid rule; At permanent location (S) Internal procedure PP TENSLAB/PRZ/2/20
20 Measuring tapes Calibration — Length
0 m to 30 m · CMC 0,148 + 0,022 · L mm
Length
Internal procedure; Comparison method using a rigid rule; At permanent location (S) Internal procedure PP TENSLAB/PRZ/2/20
21 Special vernier instruments
Weld gauges
Calibration — Length
- butt weld height — 0 mm to 15 mm · CMC 0,13 mm - fillet weld height — 0 mm to 20 mm · CMC 0,13 mm - undercut depth — up to 7 mm · CMC 0,07 mm
Length
Internal procedure; Direct method using gauge blocks and measuring rollers; At permanent location (S) Internal procedure PP TENSLAB/SP/2/18
22 Setting rings Calibration — Length
2 mm do 8 mm · CMC 2,0 µm 8 mm do 30 mm · CMC 2,1 µm 30 mm do 60 mm · CMC 2,2 µm 60 mm do 100 mm · CMC 2,4 µm 100 mm do 150 mm · CMC 2,7 µm 150 mm to 175 mm · CMC 4,0 µm
Length
Internal procedure; Direct method using a horizontal length measuring machine and a setting ring; At permanent location (S) Internal procedure PP TENSLAB/PWz/4/25 based on EURAMET cg-6 Version 2.0 (03/2011)
23 Cylindrical thread plug gauges Calibration — Length
0 mm to 40 mm · CMC 4 µm 40 mm to 60 mm · CMC 4,1 µm 60 mm to 100 mm · CMC 4,4 µm 100 mm to 200 mm · CMC 4,8 µm
Length
Internal procedure; Direct method using a horizontal length measuring machine; At permanent location (S) Internal procedure PP TENSLAB/SGT/4/25
24 Cylindrical thread ring gauges Calibration — Length
2,5 mm to 4 mm · CMC 3,1 µm 4 mm to 80 mm · CMC 3,6 µm 80 mm to 100 mm · CMC 3,7 µm 100 mm to 200 mm · CMC 4,1 µm 200 mm to 225 mm · CMC 4,5 µm
Length
Internal procedure; Direct method using a horizontal length measuring machine; At permanent location (S) Internal procedure PP TENSLAB/SGP/5/25 based on EURAMET cg-10 Version 2.1 (12/2012)
25 Taper thread plug gauges Calibration — Length
3 mm to 100 mm · CMC 4,0 µm
Length
Internal procedure; Direct method using a horizontal length measuring machine; At permanent location (S) Internal procedure PP TENSLAB/SGS/1/20
26 Taper thread ring gauges Calibration — Length
3 mm to 100 mm · CMC 4,0 µm
Length
Internal procedure; Direct method using a horizontal length measuring machine; At permanent location (S) Internal procedure PP TENSLAB/SGS/1/20
27 Plain ring gauges Calibration — Length
8 mm do 30 mm · CMC 2,0 µm 30 mm do 60 mm · CMC 2,1 µm 60 mm do 100 mm · CMC 2,6 µm 100 mm do 150 mm · CMC 2,8 µm 150 mm to 175 mm · CMC 3,0 µm
Length
Internal procedure; Direct method using a horizontal length measuring machine; At permanent location (S) Internal procedure PP TENSLAB/WZ.WEW/2/25
28 Plug gauges Calibration — Length
1 mm to 50 mm · CMC 1,1 µm 50 mm to 100 mm · CMC 1,9 µm 100 mm to 200 mm · CMC 2,5 µm
Length
Internal procedure; Direct method using a horizontal length measuring machine; At permanent location (S) Internal procedure PP TENSLAB/SO/3/25
29 Vernier calipers Calibration — Length
0 mm do 150 mm · CMC 20 µm 0 mm do 300 mm · CMC 27 µm 0 mm do 400 mm · CMC 28 µm 0 mm do 500 mm · CMC 30 µm 0 mm to 600 mm · CMC 33 µm 0 mm to 1000 mm · CMC 50 µm 0 mm do 1500 mm · CMC 70 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/SUW/4/18
30 Two-point inside micrometers Calibration — Length
0 mm to 100 mm · CMC 3,6 µm 0 mm to 175 mm · CMC 5,3 µm 0 mm to 275 mm · CMC 6,7 µm 0 mm to 375 mm · CMC 8,5 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/SM/1/18
31 Three-point inside micrometers Calibration — Length
2 mm to 100 mm · CMC 3,7 µm 100 mm to 200 mm · CMC 4,7 µm
Length
Internal procedure; Direct method using setting rings; At permanent location (S) Internal procedure PP TENSLAB/PMwew/1/19
32 Dial bore gauges Calibration — Length
0 mm to 100 mm · CMC 3,5 µm 100 mm to 300 mm · CMC 6,5 µm 300 mm to 500 mm · CMC 10,0 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/Ścz/1/22
33 Feeler gauges Calibration — Length
- leaf type — 0,02 mm to 2 mm · CMC 2,4 µm
Length
Internal procedure; Direct method using a micrometer; At permanent location (S) Internal procedure PP TENSLAB/SzL/1/23
34 Measuring rollers Calibration — Length
0 mm to 30 mm · CMC 0,9 µm
Length
Internal procedure; Direct method using a horizontal length measuring machine; At permanent location (S) Internal procedure PP TENSLAB/WP/3/25
35 Setting standards for internal dimensions Calibration — Length
8 mm do 30 mm · CMC 2,0 µm 30 mm do 60 mm · CMC 2,1 µm 60 mm do 100 mm · CMC 2,6 µm 100 mm do 150 mm · CMC 2,8 µm 150 mm to 175 mm · CMC 3,0 µm
Length
Internal procedure; Direct method using a horizontal length measuring machine; At permanent location (S) Internal procedure PP TENSLAB/WZ.WEW/2/25
36 Vernier height gauges Calibration — Length
0 mm do 300 mm · CMC 27 µm 0 mm do 400 mm · CMC 29 µm 0 mm do 500 mm · CMC 30 µm 0 mm to 600 mm · CMC 34 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/WYS.SUW/1/18
37 Setting standards for external dimensions Calibration — Length
0 mm to 500 mm · CMC 0,5 + 10 · L µm
Length
Internal procedure; Direct method using a horizontal length measuring machine; At permanent location (S) Internal procedure PP TENSLAB/WZ.ZEW/4/25
38 Builder's spirit levels Calibration — Angle
0 m to 2,5 m · CMC 0,1°
Angle
Internal procedure; Direct method using an optical dividing head; At permanent location (S) Internal procedure PP TENSLAB/Poz/1/25
39 Digital levels Calibration — Angle
4 x 90° · CMC 0,1°
Angle
Internal procedure; Direct method using an optical dividing head; At permanent location (S) Internal procedure PP TENSLAB/Poz/1/25
40 90° squares Calibration — Angle
up to 400 mm longer arm length · CMC 7 µm
Angle
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/KK/1/18
41 Protractors Calibration — Angle
- marking-out — 4 x 90° · CMC 5’ - universal; - digital — 0° to 360° · CMC 5’
Angle
Internal procedure; Direct method using angle gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/KĄT/1/18
42 Squares Calibration — Angle
0° to 210° · CMC 10’
Angle
Internal procedure; Direct method using angle gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/KĄT/1/18
43 Weld gauges (bevel angle) Calibration — Angle
80° to 180° · CMC 0,6°
Angle
Internal procedure; Direct method using angle gauge blocks; At permanent location (S) Internal procedure PP TENSLAB/SP/2/18
44 Stylus profilometers Calibration — Length (surface geometry)
Ra: — 0 µm to 0,4 µm · CMC 0,10 µm Ra: — 0 µm to 2,93 µm · CMC 0,15 µm Ra: — 0 µm to 6,5 µm · CMC 0,26 µm Rz: — 0 µm to 1,5 µm · CMC 0,15 µm Rz: — 0 µm to 11,3 µm · CMC 0,63 µm Rz: — 0 µm to 19,81 µm · CMC 1,12 µm
Length (surface geometry)
Internal procedure; Direct method using roughness standards; At permanent location (S) Internal procedure PP TENSLAB/MCH/2/20
45 Torque wrenches Calibration — Torque
0,4 Nm to 20 Nm · CMC 1,7 % 20 Nm to 3000 Nm · CMC 0,9 %
Torque
At permanent location (S) PN EN ISO 6789-1:2017-03 PN EN ISO 6789-2:2017-03
46 Torque screwdrivers Calibration — Torque
0,4 Nm to 20 Nm · CMC 1,7 %
Torque
At permanent location (S) PN EN ISO 6789-1:2017-03 PN EN ISO 6789-2:2017-03
47 Brinell hardness tester Calibration — Hardness
Hardness — HBW 2,5/187,5 · CMC 2,0 % Hardness — HBW 10/3000 · CMC 2,0 % Force — 1839 N to 29420 N · CMC 0,22 % Length — 0 mm to 1 mm · CMC 0,6 µm Length — 1 mm to 8 mm · CMC 1,5 µm
Hardness
Internal procedure; At permanent location (S) and outside of it (P) Internal procedure PP TENSLAB/TB/1/24 based on PN-EN ISO 6506-2:2019
48 Rockwell hardness testers Calibration — Hardness
Hardness — HRBW · CMC 1 HRBW Hardness — HRC · CMC 0,8 HRC Force — 98,07 N to 1471 N · CMC 0,22 %
Hardness
Internal procedure; At permanent location (S) and outside of it (P) Internal procedure PP TENSLAB/TR/2/24 based on PN-EN ISO 6508- 2:2024
49 Vickers hardness testers Calibration — Hardness
Hardness — 200 HV30 to 800 HV30 · CMC 2 % Hardness — 200 HV10 to 800 HV10 · CMC 2 % Hardness — 200 HV5 to 800 HV5 · CMC 2 % Force — 49,03 N to 294,2 N · CMC 0,22 % Length — 0 mm to 1 mm · CMC 0,6 µm
Hardness
Internal procedure; At permanent location (S) and outside of it (P) Internal procedure PP TENSLAB/TV/1/22 based on PN-EN ISO 6507-2:2018
50 Thermohygrometers
Hygrometers
Calibration — Relative humidity
28 %rh to 78 %rh · CMC 2,1 %rh
Relative humidity
Internal procedure; Calibration in the temperature range 10 °C to 35 °C; At permanent location (S) Internal procedure PP TENSLAB/TH/3/22
51 Bourdon tube pressure gauges
Electronic pressure gauges
Calibration — Pressure
-0,1 MPa do 0,25 MPa · CMC 1,2 · 10⁻⁴ MPa 0,25 MPa do 1 MPa · CMC 4,1 · 10⁻⁴ MPa 1 MPa do 4 MPa · CMC 1,2 · 10⁻³ MPa 4 MPa do 10 MPa · CMC 2,9 · 10⁻³ MPa 10 MPa do 35 MPa · CMC 1,0 ∙ 10⁻² MPa 35 MPa do 70 MPa · CMC 2,3 ∙ 10⁻² MPa 70 MPa do 100 MPa · CMC 5,8 · 10⁻² MPa 100 MPa to 160 MPa · CMC 2,0 ∙ 10⁻¹ MPa 160 MPa do 200 MPa · CMC 2,4 ∙ 10⁻¹ MPa 200 MPa do 250 MPa · CMC 3,0 ∙ 10⁻¹ MPa
Pressure
Internal procedure; At permanent location (S) Internal procedure PP TENSLAB/CE/1/18 PN EN 837-1:2000
52 Electrical thermometers (including electronic) for air temperature measurement (calibration in a climatic chamber) Calibration — Temperature (electrical thermometry)
10 °C to 35 °C · CMC 0,2 °C
Temperature (electrical thermometry)
Internal procedure; At permanent location (S) Internal procedure PP TENSLAB/TH/3/22
53 Electrical thermometers (including electronic): Calibration — Temperature (electrical thermometry)
- calibrated in a liquid bath — -25 °C to 0 °C · CMC 0,59 °C - calibrated in a liquid bath — 0 °C to 100 °C · CMC 0,10 °C - calibrated in a temperature calibrator — 50 °C to 150 °C · CMC 0,24 °C - calibrated in a temperature calibrator — 150 °C to 300 °C · CMC 0,28 °C
Temperature (electrical thermometry)
Internal procedure; At permanent location (S) Internal procedure PP TENSLAB/TE/2/20
54 Pyrometers (including radiation pyrometers, thermal imaging cameras) Calibration — Temperature (radiation thermometry)
0 °C do 100 °C · CMC 1,4 °C 100 °C to 200 °C · CMC 1,6 °C 200 °C do 350 °C · CMC 2,0 °C 350 °C do 500 °C · CMC 2,4 °C
Temperature (radiation thermometry)
Internal procedure; At permanent location (S) Internal procedure PP TENSLAB/BPT/1/20
55 Ultrasonic flaw detectors Calibration — RF electrical quantities; Time (time interval); Frequency
- measurement of transmitter pulse voltage — 30 V to 500 V · CMC 4 % - measurement of transmitter pulse time interval — 2 ns to 10 ns · CMC 2,4 % + 0,43 ns - measurement of transmitter pulse time interval — 10 ns to 10 ms · CMC 4,81 % + 0,13 ns - measurement of amplifier frequency response — 0,01 MHz to 25 MHz · CMC 0,0001 MHz - measurement of equivalent input noise level — 2 · 10⁻¹¹ V/√Hz to 1 · 10⁻⁴ V/√Hz · CMC 0,2 · 10⁻⁸ V/√Hz - measurement of attenuator accuracy — 0 dB to 100 dB · CMC 0,3 dB - measurement of time base linearity — 0,01 % WE to 100 % WE1) · CMC 0,15 % WE1)
RF electrical quantities; Time (time interval); Frequency
group 2 tests; At permanent location (S) PN-EN ISO 22232-1:2021-02
56 Ultrasonic thickness gauges Calibration — RF electrical quantities; Time (time interval); Frequency
- measurement of transmitter pulse voltage — 30 V to 500 V · CMC 4 % - measurement of transmitter pulse time interval — 2 ns to 10 ms · CMC 2,4 % + 0,43 ns - measurement of transmitter pulse time interval — 10 ns to 10 ms · CMC 4,81 % + 0,13 ns
RF electrical quantities; Time (time interval); Frequency
group 2 tests; At permanent location (S) PN-EN 15317:2014-02 excluding cl. 9.4, 9.6, 9.7, 9.9, 9.12, 9.13, 9.16

Reference standards (47)

EURAMET cg-10 Version 2.1 (12/2012)
EURAMET cg-2 Version 2.1 (02/2023)
EURAMET cg-6 Version 2.0 (03/2011)
PN EN 837-1:2000
PN EN ISO 6789-1:2017-03
PN EN ISO 6789-2:2017-03
PN-EN 15317:2014-02
PN-EN ISO 22232-1:2021-02
PN-EN ISO 3650:2000
PN-EN ISO 6506-2:2019
PN-EN ISO 6507-2:2018
PN-EN ISO 6508- 2:2024
PP TENSLAB/BPT/1/20
PP TENSLAB/CE/1/18
PP TENSLAB/CZ/5/24
PP TENSLAB/GŁ/3/18
PP TENSLAB/KK/1/18
PP TENSLAB/KOMP/1/22
PP TENSLAB/KĄT/1/18
PP TENSLAB/MCH/2/20
PP TENSLAB/MGR/2/24
PP TENSLAB/MIKR.ZEW/5/18
PP TENSLAB/PCZ/1/25
PP TENSLAB/PMwew/1/19
PP TENSLAB/PRZ/2/20
PP TENSLAB/PWz/4/25
PP TENSLAB/Poz/1/25
PP TENSLAB/SGP/5/25
PP TENSLAB/SGS/1/20
PP TENSLAB/SGT/4/25
PP TENSLAB/SM/1/18
PP TENSLAB/SO/3/25
PP TENSLAB/SP/2/18
PP TENSLAB/SUW/4/18
PP TENSLAB/SzL/1/23
PP TENSLAB/TB/1/24
PP TENSLAB/TE/2/20
PP TENSLAB/TH/3/22
PP TENSLAB/TR/2/24
PP TENSLAB/TV/1/22
PP TENSLAB/UMG/2/19
PP TENSLAB/WP/3/25
PP TENSLAB/WYS.SUW/1/18
PP TENSLAB/WZ.GR/2/25
PP TENSLAB/WZ.WEW/2/25
PP TENSLAB/WZ.ZEW/4/25
PP TENSLAB/Ścz/1/22

The same scope as data (JSON): https://labcoda.pl/api/accreditation-scopes/labs/PL/AP%20180