🇵🇱 LAB MESK Spółka Cywilna Marcin Tokaj Magdalena Tokaj PL

PCA AP 171 • Warszawa, Poland • 75 calibration items

Metrology & calibration

LAB MESK Spółka Cywilna Marcin Tokaj Magdalena Tokaj is a calibration laboratory accredited by PCA under number AP 171 (Warszawa, Poland). Its accreditation scope covers 75 calibration items in the following areas: Metrology & calibration. Calibrated items include: Weld gauges, Dial calipers, Feeler gauges, Gauge blocks (classes 0, 1 ,2). Most frequently used calibration principles: Internal procedure; Direct method using gauge blocks; At permanent…, Internal procedure; Direct method using the Mahr Precimar ICM 100 i…, Internal procedure; At permanent location (S).

At a glance

  • Accreditation number: PCA AP 171
  • Calibration items in scope: 75
  • Types of calibrated items: 68
  • Calibration principles used: 22
  • City: Warszawa, Poland
  • Valid until: 15-01-2029
Accreditation number
AP 171
Accreditation body
PCA
Address
ul. Wólczyńska 133, bud. 5, lok. 54i , 01-919 Warszawa
City
Warszawa, Poland
Valid until
15-01-2029

What this laboratory calibrates (68)

Calibration principles (22)

Certificate information

Issue date
17.10.2025
Issue no.
11
Certificate date
05.11.2024
Accreditation cycle
07.01.2025 — 15.01.2029
Approved by
Katarzyna Wiśniewska

Accreditation scope — calibration items (75)

The uncertainty covered by the CMC is the expanded uncertainty with a coverage probability of approximately 95 % and is expressed in measurand units. A CMC uncertainty value expressed as a percentage is the relative measurement uncertainty and refers to the percentage of the value of the measurand.

No. Calibrated quantity / subject of calibration Nominal range / parameters / CMC Calibration principle Calibration procedure
Calibration items
1 Analogue dial gauges with a scale interval of 0,1 mm Calibration — Length
0 mm do 30 mm · CMC 9 µm 0 mm to 50 mm · CMC 10 µm
Length
Internal procedure; Direct method using the Mahr Precimar ICM 100 instrument; At permanent location (S) Internal procedure IW5.8.49
2 Analogue dial gauges with a scale interval of 0,01 mm Calibration — Length
0 mm do 10 mm · CMC 1,2 µm 0 mm do 30 mm · CMC 1,8 µm 0 mm to 50 mm · CMC 2,5 µm 0 mm do 100 mm · CMC 4,7 µm
Length
Internal procedure; Direct method using the Mahr Precimar ICM 100 instrument; At permanent location (S) Internal procedure IW5.8.49
3 Analogue dial gauges with a scale interval of 0,005 mm Calibration — Length
0 mm to 5 mm · CMC 0,8 µm
Length
Internal procedure; Direct method using the Mahr Precimar ICM 100 instrument; At permanent location (S) Internal procedure IW5.8.49
4 Analogue dial gauges with a scale interval of 0,002 mm Calibration — Length
0 mm to 1 mm · CMC 0,7 µm
Length
Internal procedure; Direct method using the Mahr Precimar ICM 100 instrument; At permanent location (S) Internal procedure IW5.8.49
5 Analogue dial gauges with a scale interval of 0,001 mm Calibration — Length
0 mm to 1 mm · CMC 0,6 µm
Length
Internal procedure; Direct method using the Mahr Precimar ICM 100 instrument; At permanent location (S) Internal procedure IW5.8.49
6 Lever-type analogue dial gauges with a scale interval of 0,01 mm Calibration — Length
0 mm to 3 mm · CMC 1,2 µm
Length
Internal procedure; Direct method using the Mahr Precimar ICM 100 instrument; At permanent location (S) Internal procedure IW5.8.49
7 Lever-type analogue dial gauges with a scale interval of 0,002 mm; 0,001 mm Calibration — Length
0 mm to 0,6 mm · CMC 0,8 µm
Length
Internal procedure; Direct method using the Mahr Precimar ICM 100 instrument; At permanent location (S) Internal procedure IW5.8.49
8 Digital dial gauges with a resolution of 0,01 mm Calibration — Length
0 mm to 50,8 mm · CMC 9 µm 0 mm do 100 mm · CMC 10 µm
Length
Internal procedure; Direct method using the Mahr Precimar ICM 100 instrument; At permanent location (S) Internal procedure IW5.8.49
9 Digital dial gauges with a resolution of 0,005 mm Calibration — Length
0 mm to 50,8 mm · CMC 5 µm 0 mm do 100 mm · CMC 6 µm
Length
Internal procedure; Direct method using the Mahr Precimar ICM 100 instrument; At permanent location (S) Internal procedure IW5.8.49
10 Digital dial gauges with a resolution of 0,001 mm Calibration — Length
0 mm do 12,7 mm · CMC 1,3 µm 0 mm do 25,4 mm · CMC 1,6 µm 0 mm to 50,8 mm · CMC 2,5 µm 0 mm do 100 mm · CMC 4,7 µm
Length
Internal procedure; Direct method using the Mahr Precimar ICM 100 instrument; At permanent location (S) Internal procedure IW5.8.49
11 Digital dial gauges with a resolution of 0,0001 mm Calibration — Length
0 mm to 12,7 mm · CMC 1,0 µm
Length
Internal procedure; Direct method using the Mahr Precimar ICM 100 instrument; At permanent location (S) Internal procedure IW5.8.49
12 Optical probes Calibration — Length
± 20 µm · CMC 0,12 µm ± 100 µm · CMC 0,13 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.19
13 Abbe horizontal length measuring machines Calibration — Length
0 mm to 100 mm · CMC 0,5 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.8
14 Reference foils Calibration — Length
0 mm to 1 mm · CMC 2,9 µm 0 mm to 2 mm · CMC 5,5 µm 0 mm to 3 mm · CMC 8,2 µm 0 mm to 4 mm · CMC 10,9 µm 0 mm to 5 mm · CMC 13,6 µm
Length
Internal procedure; Direct method using a horizontal length measuring machine; At permanent location (S) Internal procedure IW5.8.30
15 Dial depth gauges with a resolution of 0,001 mm Calibration — Length
0 mm do 5 mm · CMC 0,3 µm 0 mm do 10 mm · CMC 0,9 µm 0 mm do 30 mm · CMC 1,3 µm 0 mm to 50 mm · CMC 1,7 µm 0 mm do 100 mm · CMC 2,9 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.16
16 Dial depth gauges with a resolution of 0,002 mm, 0,005 mm Calibration — Length
0 mm to 5 mm · CMC 0,3 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.16
17 Dial depth gauges with a resolution of 0,01 mm Calibration — Length
0 mm to 50 mm · CMC 6,6 µm 0 mm do 100 mm · CMC 7,0 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.16
18 Dial depth gauges with a scale interval of 0,01 mm Calibration — Length
0 mm do 10 mm · CMC 0,9 µm 0 mm do 30 mm · CMC 1,3 µm 0 mm to 50 mm · CMC 1,7 µm 0 mm do 100 mm · CMC 2,9 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.16
19 Dial depth gauges with a scale interval of 0,1 mm Calibration — Length
0 mm to 50 mm · CMC 6,6 µm 0 mm do 100 mm · CMC 7,0 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.16
20 Micrometer depth gauges Calibration — Length
0 mm to 25 mm · CMC 1,1 µm 25 mm to 50 mm · CMC 1,6 µm 50 mm to 75 mm · CMC 2,2 µm 75 mm to 100 mm · CMC 2,9 µm 100 mm to 125 mm · CMC 3,7 µm 125 mm to 150 mm · CMC 4,3 µm 150 mm to 175 mm · CMC 4,9 µm 175 mm to 200 mm · CMC 5,5 µm 200 mm do 225 mm · CMC 6,2 µm 225 mm do 250 mm · CMC 6,8 µm 250 mm do 275 mm · CMC 7,5 µm 275 mm do 300 mm · CMC 8,1 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.17
21 Vernier depth gauges Calibration — Length
0 mm do 150 mm · CMC 10 µm 0 mm to 200 mm · CMC 10 µm 0 mm do 300 mm · CMC 12 µm 0 mm do 500 mm · CMC 17 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.3
22 Micrometer heads Calibration — Length
0 mm to 25 mm · CMC 1,0 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.31
23 Dial thickness gauges with a resolution of 0,001 mm Calibration — Length
0 mm do 10 mm · CMC 1,4 µm 0 mm to 50 mm · CMC 1,4 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.10
24 Dial thickness gauges with a resolution of 0,01 mm Calibration — Length
0 mm to 50 mm · CMC 6 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.10
25 Dial thickness gauges with a scale interval of 0,01 mm Calibration — Length
0 mm do 10 mm · CMC 1,4 µm 0 mm to 50 mm · CMC 1,4 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.10
26 Dial thickness gauges with a scale interval of 0,1 mm Calibration — Length
0 mm to 50 mm · CMC 6 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.10
27 Dial calipers Calibration — Length
- for internal measurements — 2,5 mm to 12,5 mm · CMC 1,1 µm - for internal measurements — 10 mm to 22 mm · CMC 1,4 µm - for internal measurements — 10 mm to 35 mm · CMC 1,6 µm - for internal measurements — 30 mm to 55 mm · CMC 1,8 µm - for internal measurements — 40 mm to 90 mm · CMC 2,8 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.22
28 Dial calipers Calibration — Length
- for external measurements — 0 mm to 20 mm · CMC 1,0 µm - for external measurements — 20 mm to 40 mm · CMC 1,3 µm - for external measurements — 40 mm to 60 mm · CMC 1,8 µm - for external measurements — 60 mm to 80 mm · CMC 2,3 µm - for external measurements — 80 mm to 100 mm · CMC 2,8 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.22
29 Coating thickness gauges Calibration — Length
0 µm to 1000 µm · CMC 3,3 µm 1000 µm to 2000 µm · CMC 5,6 µm 2000 µm to 3000 µm · CMC 8,3 µm 3000 µm to 4000 µm · CMC 10,5 µm 4000 µm to 5150 µm · CMC 14,0 µm
Length
Internal procedure; Direct method using reference foils; At permanent location (S) Internal procedure IW5.8.43
30 Internal micrometers Calibration — Length
5 mm do 30 mm · CMC 1,1 µm 25 mm to 50 mm · CMC 1,6 µm 50 mm to 75 mm · CMC 2,2 µm 75 mm to 100 mm · CMC 2,9 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.23
31 External micrometers Calibration — Length
0 mm to 25 mm · CMC 1,0 µm 25 mm to 50 mm · CMC 1,5 µm 50 mm to 75 mm · CMC 2,2 µm 75 mm to 100 mm · CMC 2,8 µm 100 mm to 125 mm · CMC 3,7 µm 125 mm to 150 mm · CMC 4,3 µm 150 mm to 175 mm · CMC 4,9 µm 175 mm to 200 mm · CMC 5,5 µm 200 mm do 225 mm · CMC 6,2 µm 225 mm do 250 mm · CMC 6,8 µm 250 mm do 275 mm · CMC 7,5 µm 275 mm do 300 mm · CMC 8,1 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.4
32 Indicating micrometers Calibration — Length
- indicator system — from -140 µm to +140 µm · CMC 1,0 µm - micrometer system — 0 mm to 25 mm · CMC 1,2 µm - micrometer system — 0 mm to 50 mm · CMC 1,5 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.18
33 Setting rings Calibration — Length
2 mm to 30 mm · CMC 1,8 µm
Length
Internal procedure; Direct method using the Trimos Labconcept Premium 500 length measuring machine fitted with an electronic probe; At permanent location (S) Internal procedure IW5.8.44 based on EURAMET cg-6 Version 2.0 (03/2011)
34 Setting rings Calibration — Length
10 mm to 50 mm · CMC 1,4 µm 50 mm to 80 mm · CMC 1,5 µm 80 mm to 110 mm · CMC 1,7 µm 110 mm to 150 mm · CMC 1,9 µm 150 mm to 190 mm · CMC 2,2 µm 190 mm to 225 mm · CMC 2,4 µm 225 mm to 260 mm · CMC 2,9 µm 260 mm to 300 mm · CMC 3,2 µm
Length
Internal procedure; Direct method using the Trimos Labconcept Premium 500 length measuring machine fitted with contact arms; At permanent location (S) Internal procedure IW5.8.6 based on EURAMET cg-6 Version 2.0 (03/2011)
35 Gauge blocks (classes 0, 1 ,2) Calibration — Length
0,5 mm to 100 mm · CMC Q[0,073; 0,86⋅L] µm
Length
Internal procedure; At permanent location (S) Internal procedure IW5.8.13 based on PN-EN ISO 3650:2000
36 Gauge blocks (classes 0, 1 ,2) Calibration — Length
0,1 mm to 100 mm · CMC Q[0,095; 0,9⋅L] µm
Length
Internal procedure; Differential method using the Mitutoyo GBCD-250 two-probe comparator; At permanent location (S) Internal procedure IW5.8.13
37 Semi-rigid rules
Rigid rules
Calibration — Length
0 mm to 1000 mm · CMC 0,12 mm 1000 mm do 3000 mm · CMC 0,18 mm 3000 mm do 5000 mm · CMC 0,25 mm
Length
Internal procedure; Comparison method using a rigid rule; At permanent location (S) Internal procedure IW5.8.21
38 Measuring tapes Calibration — Length
0 mm to 2000 mm · CMC 0,14 mm 2000 mm to 5000 mm · CMC 0,25 mm 5000 mm to 8000 mm · CMC 0,33 mm 8000 mm to 10000 mm · CMC 0,37 mm 10000 mm to 15000 mm · CMC 0,45 mm
Length
Internal procedure; Comparison method using a rigid rule; At permanent location (S) Internal procedure IW5.8.21
39 Weld gauges Calibration — Length
- measurement of butt weld height — 0 mm to 15 mm · CMC 0,06 mm - measurement of fillet weld height — 0 mm to 20 mm · CMC 0,06 mm - measurement of fillet weld throat thickness — 0 mm to 15 mm · CMC 0,06 mm - measurement of weld width — 0 mm to 60 mm · CMC 0,6 mm - measurement of undercut depth — 0 mm to 6 mm · CMC 0,06 mm
Length
Internal procedure; Direct method using gauge blocks and measuring rollers; At permanent location (S) Internal procedure IW5.8.40
40 Weld gauges Calibration — Length
- butt weld height — 0 mm to 30 mm · CMC 6 µm - fillet weld throat thickness — 0 mm to 30 mm · CMC 12 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.33
41 Taper thread ring gauges Calibration — Length
pitch diameter d2 — 7 mm to 87 mm · CMC 5,0 µm
Length
Internal procedure; Indirect method using the Trimos Labconcept Premium 500 length measuring machine; At permanent location (S) Internal procedure IW5.8.46
42 Cylindrical thread ring gauges Calibration — Length
pitch diameter d2 — 2,1 mm to 50 mm · CMC 3,0 µm pitch diameter d2 — 50 mm to 112 mm · CMC 3,1 µm pitch diameter d2 — 112 mm to 174 mm · CMC 3,7 µm
Length
Internal procedure; Indirect method using the Trimos Labconcept Premium 500 length measuring machine fitted with an electronic probe; At permanent location (S) Internal procedure IW5.8.45 based on EURAMET cg-10 Version 2.1 (12/2012)
43 Taper thread plug gauges Calibration — Length
pitch diameter d2 — 9 mm to 112 mm · CMC 5,0 µm
Length
Internal procedure; Indirect method using the Trimos Labconcept Premium 500 length measuring machine; At permanent location (S) Internal procedure IW5.8.46
44 Cylindrical thread plug gauges Calibration — Length
pitch diameter d2 — 1,5 mm to 100 mm · CMC 3,0 µm pitch diameter d2 — 100 mm to 125 mm · CMC 3,2 µm
Length
Internal procedure; Indirect method using measuring rollers and the Trimos Labconcept Premium 500 length measuring machine; At permanent location (S) Internal procedure IW5.8.7 based on EURAMET cg-10 Version 2.1 (12/2012)
45 Plain ring gauges Calibration — Length
2 mm to 30 mm · CMC 1,8 µm
Length
Internal procedure; Direct method using the Trimos Labconcept Premium 500 length measuring machine fitted with an electronic probe; At permanent location (S) Internal procedure IW5.8.44 based on EURAMET cg-6 Version 2.0 (03/2011)
46 Plain ring gauges Calibration — Length
10 mm to 50 mm · CMC 1,4 µm 50 mm to 80 mm · CMC 1,5 µm 80 mm to 110 mm · CMC 1,7 µm 110 mm to 150 mm · CMC 1,9 µm 150 mm to 190 mm · CMC 2,2 µm 190 mm to 225 mm · CMC 2,4 µm 225 mm to 260 mm · CMC 2,9 µm 260 mm to 300 mm · CMC 3,2 µm
Length
Internal procedure; Direct method using the Trimos Labconcept Premium 500 length measuring machine fitted with contact arms; At permanent location (S) Internal procedure IW5.8.6 based on EURAMET cg-6 Version 2.0 (03/2011)
47 Special gauges Calibration — Length
5 mm to 50 mm · CMC 1,8 µm
Length
Internal procedure; Direct method using the Trimos Labconcept Premium 500 length measuring machine fitted with an electronic probe; At permanent location (S) Internal procedure IW5.8.48
48 Special gauges Calibration — Length
14 mm to 50 mm · CMC 1,4 µm 50 mm to 80 mm · CMC 1,5 µm 80 mm to 110 mm · CMC 1,7 µm 110 mm to 150 mm · CMC 1,9 µm 150 mm to 190 mm · CMC 2,2 µm 190 mm to 225 mm · CMC 2,4 µm 225 mm to 240 mm · CMC 2,6 µm
Length
Internal procedure; Direct method using the Trimos Labconcept Premium 500 length measuring machine fitted with contact arms; At permanent location (S) Internal procedure IW5.8.47
49 Plug gauges Calibration — Length
0 mm to 50 mm · CMC 0,9 µm 50 mm to 75 mm · CMC 1,0 µm 75 mm to 100 mm · CMC 1,2 µm 100 mm to 125 mm · CMC 1,3 µm 125 mm to 150 mm · CMC 1,7 µm 150 mm do 200 mm · CMC 2,1 µm
Length
Internal procedure; Direct method using the Trimos Labconcept Premium 500 length measuring machine; At permanent location (S) Internal procedure IW5.8.14
50 Vernier calipers Calibration — Length
0 mm do 150 mm · CMC 10 µm 0 mm to 200 mm · CMC 10 µm 0 mm do 300 mm · CMC 12 µm 0 mm do 500 mm · CMC 17 µm 0 mm to 600 mm · CMC 31 µm 0 mm do 800 mm · CMC 34 µm 0 mm to 1000 mm · CMC 38 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.3
51 Feeler gauges Calibration — Length
0,02 mm to 3 mm · CMC 0,9 µm
Length
Internal procedure; Direct method using a horizontal length measuring machine; At permanent location (S) Internal procedure IW5.8.12
52 Feeler gauges Calibration — Length
0,02 mm to 3 mm · CMC 1,6 µm
Length
Internal procedure; Direct method using a digital micrometer; At permanent location (S) Internal procedure IW5.8.12
53 Taper feeler gauges Calibration — Length
0 mm to 45 mm · CMC 12 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.24
54 Dial bore gauges Calibration — Length
4 mm to 18 mm · CMC 1,5 µm 18 mm to 50 mm · CMC 2,0 µm 50 mm to 150 mm · CMC 5,0 µm 150 mm to 200 mm · CMC 11 µm 200 mm to 300 mm · CMC 15 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.20
55 Two-point inside micrometers Calibration — Length
50 mm to 75 mm · CMC 1,5 µm 75 mm to 100 mm · CMC 1,8 µm 100 mm to 125 mm · CMC 2,2 µm 125 mm to 150 mm · CMC 2,3 µm 150 mm to 175 mm · CMC 2,8 µm 175 mm to 200 mm · CMC 3,5 µm 200 mm do 225 mm · CMC 4,3 µm 225 mm do 250 mm · CMC 5,2 µm 250 mm do 275 mm · CMC 5,5 µm 275 mm do 300 mm · CMC 5,8 µm 300 mm do 325 mm · CMC 6,1 µm 325 mm do 350 mm · CMC 6,3 µm 350 mm do 375 mm · CMC 6,3 µm
Length
Internal procedure; Direct method using the Trimos Labconcept Premium 500 length measuring machine; At permanent location (S) Internal procedure IW5.8.25
56 Three-point inside micrometers
Three-point dial bore gauges
Calibration — Length
3,5 mm do 12 mm · CMC 1,9 µm 12 mm do 35 mm · CMC 2,0 µm 35 mm do 50 mm · CMC 2,1 µm 50 mm do 80 mm · CMC 2,3 µm 80 mm do 100 mm · CMC 2,8 µm 100 mm to 125 mm · CMC 2,9 µm 125 mm to 150 mm · CMC 3,3 µm 150 mm to 175 mm · CMC 3,5 µm 175 mm to 200 mm · CMC 4,6 µm 200 mm do 250 mm · CMC 4,8 µm 250 mm do 275 mm · CMC 4,9 µm 275 mm do 300 mm · CMC 5,3 µm
Length
Internal procedure; Direct method using setting rings; At permanent location (S) Internal procedure IW5.8.15
57 Indicating snap gauges Calibration — Length
0 mm to 25 mm · CMC 0,9 µm 25 mm to 50 mm · CMC 1,0 µm 50 mm to 75 mm · CMC 1,2 µm 75 mm to 100 mm · CMC 1,3 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.5
58 Measuring rollers Calibration — Length
0 mm to 20 mm · CMC 0,5 µm
Length
Internal procedure; Comparison method using gauge blocks and a MOP 02/20 type probe; At permanent location (S) Internal procedure IW5.8.26
59 Measuring rollers Calibration — Length
0 mm to 30 mm · CMC 1,0 µm
Length
Internal procedure; Direct method using the Trimos Labconcept Premium 500 length measuring machine; At permanent location (S) Internal procedure IW5.8.26
60 Digital height gauges with resolution Calibration — Length
- 0,01 mm — 0 mm to 600mm · CMC Q[5,9; 8,3∙L] µm - 0,005 mm — 0 mm to 600mm · CMC Q[3,1; 8,3∙L] µm - 0,001 mm — 0 mm to 600mm · CMC Q[0,7; 8,3∙L] µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.50
61 Vernier height gauges Calibration — Length
0 mm do 300 mm · CMC 12 µm 0 mm do 500 mm · CMC 17 µm 0 mm to 600 mm · CMC 20 µm 0 mm do 800 mm · CMC 34 µm 0 mm to 1000 mm · CMC 38 µm
Length
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.3
62 Setting standards for internal dimensions Calibration — Length
up to 100 mm · CMC 2,0 µm
Length
Internal procedure; Direct method using the Trimos Labconcept Premium 500 length measuring machine fitted with contact arms; At permanent location (S) Internal procedure IW5.8.27
63 Setting standards for external dimensions Calibration — Length
25 mm · CMC 0,9 µm 25 mm to 50 mm · CMC 0,9 µm 50 mm to 75 mm · CMC 1,0 µm 75 mm to 100 mm · CMC 1,2 µm 100 mm to 125 mm · CMC 1,5 µm 125 mm to 150 mm · CMC 1,6 µm 150 mm to 175 mm · CMC 2,1 µm 175 mm to 200 mm · CMC 2,2 µm 200 mm do 225 mm · CMC 2,3 µm 225 mm do 250 mm · CMC 2,4 µm 250 mm do 275 mm · CMC 2,9 µm 275 mm do 300 mm · CMC 3,0 µm
Length
Internal procedure; Direct method using the Trimos Labconcept Premium 500 length measuring machine; At permanent location (S) Internal procedure IW5.8.9
64 Digital protractors Calibration — Angle
0° to 360° · CMC 3,6’
Angle
Internal procedure; Direct method using angle gauge blocks; At permanent location (S) Internal procedure IW5.8.28
65 Marking-out protractors Calibration — Angle
0° to 180° · CMC 0,2°
Angle
Internal procedure; Direct method using angle gauge blocks; At permanent location (S) Internal procedure IW5.8.28
66 Universal bevel protractors Calibration — Angle
4 x 90° · CMC 3,6’
Angle
Internal procedure; Direct method using angle gauge blocks; At permanent location (S) Internal procedure IW5.8.28
67 90° try squares Calibration — Angle
longer arm length up to 315 mm · CMC 5,0 µm
Angle
Internal procedure; Direct method using gauge blocks and a cylindrical square; At permanent location (S) Internal procedure IW5.8.29
68 Builder's spirit levels Calibration — Angle
- zero setting error — 0 mm to 300 mm · CMC 0,2 mm
Angle
Internal procedure; Direct method using a surface plate and a 90° square; At permanent location (S) Internal procedure IW5.8.38
69 Digital levels Calibration — Angle
± 90° · CMC 0,06°
Angle
Internal procedure; Indirect method using a sine bar and gauge blocks; At permanent location (S) Internal procedure IW5.8.38
70 Bar spirit levels Calibration — Angle
- error of the scale interval value — 0 mm/m to 1 mm/m · CMC 0,015 mm/m - zero setting error — 0 mm/m to 1 mm/m · CMC 0,2 dz. el.
Angle
Internal procedure; Direct method using a coincidence level; At permanent location (S) Internal procedure IW.5.8.38
71 Weld gauges Calibration — Angle
- bevel angle — 80° to 160° · CMC 0,6°
Angle
Internal procedure; Direct method using angle gauge blocks; At permanent location (S) Internal procedure IW5.8.40
72 Straight edges Calibration — Length (surface geometry)
0 mm to 300 mm · CMC 3 µm
Length (surface geometry)
Internal procedure; Direct method using gauge blocks; At permanent location (S) Internal procedure IW5.8.36
73 Force gauges (telecommunication dynamometers) Calibration — Force
2 cN to 245 cN · CMC 0,76 cN
Force
Internal procedure; At permanent location (S) Internal procedure IW5.8.1
74 Torque wrenches Calibration — Torque
0,5 Nm to 1500 Nm · CMC 0,62 %
Torque
Internal procedure; At permanent location (S) Internal procedure IW5.8.2 based on PN-EN ISO 6789-1:2017 PN-EN ISO 6789-2:2017
75 Torque screwdrivers Calibration — Torque
0,04 Nm to 10 Nm · CMC 0,85 %
Torque
Internal procedure; At permanent location (S) Internal procedure IW5.8.2 based on PN-EN ISO 6789-1:2017 PN-EN ISO 6789-2:2017

Reference standards (48)

EURAMET cg-10 Version 2.1 (12/2012)
EURAMET cg-6 Version 2.0 (03/2011)
IW.5.8.38
IW5.8.1
IW5.8.10
IW5.8.12
IW5.8.13
IW5.8.14
IW5.8.15
IW5.8.16
IW5.8.17
IW5.8.18
IW5.8.19
IW5.8.2
IW5.8.20
IW5.8.21
IW5.8.22
IW5.8.23
IW5.8.24
IW5.8.25
IW5.8.26
IW5.8.27
IW5.8.28
IW5.8.29
IW5.8.3
IW5.8.30
IW5.8.31
IW5.8.33
IW5.8.36
IW5.8.38
IW5.8.4
IW5.8.40
IW5.8.43
IW5.8.44
IW5.8.45
IW5.8.46
IW5.8.47
IW5.8.48
IW5.8.49
IW5.8.5
IW5.8.50
IW5.8.6
IW5.8.7
IW5.8.8
IW5.8.9
PN-EN ISO 3650:2000
PN-EN ISO 6789-1:2017
PN-EN ISO 6789-2:2017

The same scope as data (JSON): https://labcoda.pl/api/accreditation-scopes/labs/PL/AP%20171