🇵🇱 ZwickRoell Spółka z ograniczoną odpowiedzialnością Spółka komandytowa PL

PCA AP 133 • Wrocław, Poland • 19 calibration items

Metrology & calibration

ZwickRoell Spółka z ograniczoną odpowiedzialnością Spółka komandytowa is a calibration laboratory accredited by PCA under number AP 133 (Wrocław, Poland). Its accreditation scope covers 19 calibration items in the following areas: Metrology & calibration. Calibrated items include: Static testing machines, Process equipment, - for compressive forces, - for tensile forces. Most frequently used calibration principles: Outside of permanent location (P), At permanent location (S), Indirect and direct method; Outside of permanent location (P).

At a glance

  • Accreditation number: PCA AP 133
  • Calibration items in scope: 19
  • Types of calibrated items: 15
  • Calibration principles used: 6
  • City: Wrocław, Poland
  • Valid until: 05-04-2030
Accreditation number
AP 133
Accreditation body
PCA
Address
ul. Muchoborska 18, 54-424 Wrocław
City
Wrocław, Poland
Valid until
05-04-2030

What this laboratory calibrates (15)

Calibration principles (6)

Certificate information

Issue date
15.07.2026
Issue no.
18
Certificate date
22.07.2024
Accreditation cycle
23.03.2026 — 05.04.2030
Approved by
Katarzyna Wiśniewska

Accreditation scope — calibration items (19)

The uncertainty covered by the CMC is the expanded uncertainty with a coverage probability of approximately 95 % and is expressed in measurand units. A CMC uncertainty value expressed as a percentage is the relative measurement uncertainty and refers to the percentage of the value of the measurand.

No. Calibrated quantity / subject of calibration Nominal range / parameters / CMC Calibration principle Calibration procedure
Calibration items
1 Static testing machines
Process equipment
- for tensile forces
- for compressive forces
Calibration — Force
0,01 N to 200 N · CMC 0,1 %
Force
Outside of permanent location (P) PN-EN ISO 7500-1:2018-05 ASTM E4-24
2 Static testing machines
Process equipment
- for compressive forces
Calibration — Force
0,1 kN to 3000 kN · CMC 0,12 %
Force
Outside of permanent location (P) PN-EN ISO 7500-1:2018-05 ASTM E4-24
3 Static testing machines
Process equipment
- for tensile forces
- for tensile forces
Calibration — Force
0,1 kN to 2000 kN · CMC 0,12 %
Force
Outside of permanent location (P) PN-EN ISO 7500-1:2018-05 ASTM E4-24
4 Static testing machines
Process equipment
- for compressive forces
Calibration — Force
600 kN to 6000 kN · CMC 0,24 %
Force
Outside of permanent location (P) PN-EN ISO 7500-1:2018-05 ASTM E4-24
5 Extensometers Calibration — Force
0 mm to 0,3 mm · CMC 0,5 µm 0,3 mm to 1300 mm · CMC 0,15 %
Force
Outside of permanent location (P) PN-EN ISO 9513:2013-06 ASTM E83-23 ASTM E2309/E2309M-20
6 Static testing machines Calibration — Force
- crosshead speed — 0,01 mm/min to 3000 mm/min · CMC 0,2 %
Force
Outside of permanent location (P) ASTM E2658-15 (2023)
7 Static testing machines Calibration — Force
- angle of rotation — 0° to 360° · CMC 0,2°
Force
Outside of permanent location (P) VDI/VDE/DKD 2648 Part 1:2024
8 Static testing machines Calibration — Force
- torque — 0,01 N · m to 200 N · m · CMC 0,2 %
Force
Outside of permanent location (P) ASTM E2624-17
9 Pendulum impact testers Calibration — Impact strength
- energy — 0,5 J to 750 J · CMC Note1) - force — 0,2 N to 1000 N · CMC 0,12 % - pendulum length — 200 mm to 1000 mm · CMC 0,2 mm - angle — 0° to 180° · CMC 0,2° - time — 2 s to 240 s · CMC 0,05 s
Impact strength
Direct method; Outside of permanent location (P) PN-EN ISO 148-2:2017-02E PN-EN ISO 13802:2015-07E ASTM E23-25
10 Pendulum impact testers Calibration — Impact strength
- energy — 13 J to 250 J · CMC 1,5 · U_CRM J
Impact strength
Indirect method; Outside of permanent location (P) PN-EN ISO 148-2:2017-02E ASTM E23-25
11 Brinell hardness testers Calibration — Hardness
- hardness — HBW 2,5/15,625 · CMC 2,3 % - hardness — HBW 2,5/31,25 · CMC 2,3 % - hardness — HBW 2,5/62,5 · CMC 2,3 % - hardness — HBW 2,5/187,5 · CMC 2,3 % - hardness — HBW 5/250 · CMC 2,3 % - hardness — HBW 5/750 · CMC 2,3 % - hardness — HBW 10/500 · CMC 2,3 % - hardness — HBW 10/1000 · CMC 2,3 % - hardness — HBW 10/3000 · CMC 2,3 % - force — 153,2 N to 29420 N · CMC 0,12 % - cycle time — 1 s to 20 s · CMC 0,05 s - length — 0,1 mm to 0,2 mm · CMC 0,4 µm - length — 0,2 mm to 6 mm · CMC 0,2 %
Hardness
Indirect and direct method; Outside of permanent location (P) PN-EN ISO 6506-2:2019-10 ASTM E10-23
12 Vickers hardness testers Calibration — Hardness
- hardness — HV 0,025 · CMC 12 % - hardness — HV 0,05 · CMC 8% - hardness — HV 0,1 · CMC 7,3 % - hardness — HV 0,2 · CMC 7,3 % - hardness — HV 0,3 · CMC 5,1 % - hardness — HV 0,5 · CMC 4,6 % - hardness — HV 1 · CMC 4,6 % - hardness — HV 2 · CMC 4,6 % - hardness — HV 3 · CMC 4,6 % - hardness — HV 5 · CMC 2,6 % - hardness — HV 10 · CMC 2,6 % - hardness — HV 30 · CMC 2,6 % - hardness — HV 100 · CMC 2% - force — 0,2451 N to 980,7 N · CMC 0,12 % - cycle time — 1 s to 20 s · CMC 0,05 s - length — 0,01 mm to 0,2 mm · CMC 0,4 µm - length — 0,2 mm to 2 mm · CMC 0,2 %
Hardness
Indirect and direct method; Outside of permanent location (P) PN-EN ISO 6507-2:2018-05 ASTM E92-23 ASTM E384-22
13 Rockwell hardness testers Calibration — Hardness
- hardness — HRA · CMC 0,6 HRA - hardness — HRB · CMC 1 HRB - hardness — HRC · CMC 0,6 HRC - hardness — HRD · CMC 0,6 HRD - hardness — HRE · CMC 0,6 HRE - hardness — HRF · CMC 0,6 HRF - hardness — HRG · CMC 0,6 HRG - hardness — HRH · CMC 0,6 HRH - hardness — HRK · CMC 0,6 HRK - hardness — HR15N · CMC 0,6 HR15N - hardness — HR30N · CMC 0,6 HR30N - hardness — HR45N · CMC 0,6 HR45N - hardness — HR15T · CMC 0,6 HR15T - hardness — HR30T · CMC 0,6 HR30T - hardness — HR45T · CMC 0,6 HR45T - hardness — HR15W · CMC 0,6 HR15W - hardness — HR30W · CMC 0,6 HR30W - hardness — HR45W · CMC 0,6 HR45W - hardness — HR15Y · CMC 0,6 HR15Y - hardness — HR30Y · CMC 0,6 HR30Y - hardness — HR45Y · CMC 0,6 HR45Y - force — 29,42 N to 1471 N · CMC 0,12 % - length — 20 μm to 250 μm · CMC 0,3 μm - cycle time — 0,1 s to 15 s · CMC 0,05 s
Hardness
Indirect and direct method; Outside of permanent location (P) PN-EN ISO 6508-2:2024-06 ASTM E18-25
14 Knoop hardness testers Calibration — Hardness
- hardness — HK 0,025 · CMC 10 % - hardness — HK 0,05 · CMC 10 % - hardness — HK 0,1 · CMC 7,5 % - hardness — HK 0,2 · CMC 7,5 % - hardness — HK 0,3 · CMC 5% - hardness — HK 0,5 · CMC 5% - hardness — HK 1 · CMC 4% - force — 0,2451 N to 9,807 N · CMC 0,12 % - cycle time — 1 s to 20 s · CMC 0,05 s - length — 0,01 mm to 0,2 mm · CMC 0,4 µm - length — 0,2 mm to 2 mm · CMC 0,2 %
Hardness
Indirect and direct method; Outside of permanent location (P) PN-EN ISO 4545- 2:2018-04 ASTM E92-23 ASTM E384-22
15 Melt flow indexers Calibration — Length, time (time interval), force, temperature (electrical thermometry)
- length — 0 mm to 30 mm · CMC 0,15 % - time — 5 s to 240 s · CMC 0,05 s - force — 1 N to 250 N · CMC 0,12 % - temperature — 100 °C to 370 °C · CMC 0,2 °C
Length, time (time interval), force, temperature (electrical thermometry)
Internal procedure; Outside of permanent location (P) IW-M.R/ZPSLW/1 based on PN-EN ISO 1133-1:2022 PN-EN ISO 1133-2:2011
16 Shore type A durometers Calibration — Hardness
- force — 1300 mN to 8050 mN · CMC 37,5 mN - indenter displacement — 0 mm to 2,5 mm · CMC 12,5 µm - indenter diameter — 1,10 mm to 1,40 mm · CMC 4 µm - diameter of the truncated cone of the indenter — 0,78 mm to 0,80 mm · CMC 3 µm - indenter cone angle — 34,75˚ to 35,25˚ · CMC 0,16˚ - presser foot diameter — 17,5 mm to 18,5 mm · CMC 50 µm - presser foot hole diameter — 2,90 mm to 3,10 mm · CMC 4 µm
Hardness
At permanent location (S) ISO 48-9:2018
17 Shore type D durometers Calibration — Hardness
- force — 4450 mN to 44500 mN · CMC 222,5 mN - indenter displacement — 0 mm to 2,5 mm · CMC 12,5 µm - indenter diameter — 1,10 mm to 1,40 mm · CMC 4 µm - indenter radius — 0,09 mm to 0,11 mm · CMC 3 µm - indenter cone angle — 29,75˚ to 30,25˚ · CMC 0,16˚ - presser foot diameter — 17,5 mm to 18,5 mm · CMC 50 µm - presser foot hole diameter — 2,90 mm to 3,10 mm · CMC 4 µm
Hardness
At permanent location (S) ISO 48-9:2018
18 IRHD type N hardness testers Calibration — Hardness
- indenter contact force — 0,28 N to 0,32 N · CMC 0,24 % - indenter indenting force — 5,35 N to 5,45 N · CMC 0,24 % - indenter total force — 5,67 N to 5,73 N · CMC 0,24 % - presser foot force — 6,80 N to 9,80 N · CMC 0,24 % - indenter displacement — 0 mm to 1,8 mm · CMC 1 µm - indenter ball diameter — 2,49 mm to 2,51 mm · CMC 3 µm - presser foot hole diameter — 5,0 mm to 7,0 mm · CMC 50 µm - presser foot diameter — 19,0 mm to 21,0 mm · CMC 50 µm
Hardness
At permanent location (S) ISO 48-9:2018
19 IRHD type M hardness testers Calibration — Hardness
- indenter contact force — 7,8 mN to 8,8 mN · CMC 0,24 % - indenter indenting force — 143,5 mN to 146,5 mN · CMC 0,24 % - indenter total force — 152,3 mN to 154,3 mN · CMC 0,24 % - presser foot force — 205 mN to 265 mN · CMC 0,24 % - indenter displacement — 0 mm to 0,3 mm · CMC 1 µm - indenter ball diameter — 0,390 mm to 0,400 mm · CMC 3 µm - presser foot hole diameter — 0,85 mm to 1,15 mm · CMC 4 µm - presser foot diameter — 3,20 mm to 3,50 mm · CMC 4 µm
Hardness
At permanent location (S) ISO 48-9:2018

Reference standards (23)

ASTM E10-23
ASTM E18-25
ASTM E23-25
ASTM E2309/E2309M-20
ASTM E2624-17
ASTM E2658-15 (2023)
ASTM E384-22
ASTM E4-24
ASTM E83-23
ASTM E92-23
ISO 48-9:2018
IW-M.R/ZPSLW/1
PN-EN ISO 1133-1:2022
PN-EN ISO 1133-2:2011
PN-EN ISO 13802:2015-07E
PN-EN ISO 148-2:2017-02E
PN-EN ISO 4545- 2:2018-04
PN-EN ISO 6506-2:2019-10
PN-EN ISO 6507-2:2018-05
PN-EN ISO 6508-2:2024-06
PN-EN ISO 7500-1:2018-05
PN-EN ISO 9513:2013-06
VDI/VDE/DKD 2648 Part 1:2024

The same scope as data (JSON): https://labcoda.pl/api/accreditation-scopes/labs/PL/AP%20133