🇵🇱 Politechnika Krakowska im. Tadeusza Kościuszki PL

PCA AP 132 • Kraków, Poland • 23 calibration items

Metrology & calibration

Politechnika Krakowska im. Tadeusza Kościuszki is a calibration laboratory accredited by PCA under number AP 132 (Kraków, Poland). Its accreditation scope covers 23 calibration items in the following areas: Metrology & calibration. Calibrated items include: Spatial reference artefacts, Coordinate measuring arms, Coordinate measuring machines, Coordinate optical scanners. Most frequently used calibration principles: At permanent location (S) and outside of it (P), Internal procedure; At permanent location (S), At permanent location (S).

At a glance

  • Accreditation number: PCA AP 132
  • Calibration items in scope: 23
  • Types of calibrated items: 29
  • Calibration principles used: 6
  • City: Kraków, Poland
  • Valid until: 09-03-2030
Accreditation number
AP 132
Accreditation body
PCA
Address
al. Jana Pawła II 37, 31-864 Kraków
City
Kraków, Poland
Division
Coordinate Metrology Laboratory
Valid until
09-03-2030

What this laboratory calibrates (29)

Calibration principles (6)

Certificate information

Issue date
11.02.2026
Issue no.
19
Certificate date
02.03.2020
Accreditation cycle
11.02.2026 — 09.03.2030
Approved by
Tadeusz Matras

Accreditation scope — calibration items (23)

The uncertainty covered by the CMC is the expanded uncertainty with a coverage probability of approximately 95 % and is expressed in measurand units.

No. Calibrated quantity / subject of calibration Nominal range / parameters / CMC Calibration principle Calibration procedure
Calibration items
1 Reference spheres
Reference rings
Cylindrical standards
Calibration — Length
5 mm to 50 mm · CMC 0,12 µm
Length
At permanent location (S) PN-EN ISO 15530-3:2011
2 Length standards
Setting standards for external dimensions
Setting standards for internal dimensions
Calibration — Length
up to 1000 mm · CMC (0,08 + 0,3 · L) µm L - wielkość mierzona (m) up to 5000 mm · CMC (1,0 + 1,0 · L) µm L - wielkość mierzona (m)
Length
Internal procedure; At permanent location (S) P2-I1
3 Reference spheres
Reference rings
Cylindrical standards
Calibration — Length (surface geometry)
5 mm to 50 mm · CMC 0,05 µm
Length (surface geometry)
Internal procedure; At permanent location (S) P2-I3
4 Non-contact profilometers Calibration — Length (surface geometry)
Pt: up to 1000 µm · CMC (0,1 + 0,005 · Pt) µm Ra: 0,1 µm to 13 µm · CMC (0,025 + 0,02 · Ra) µm Rz: 1 µm to 52 µm · CMC (0,04 + 0,025 · Rz) µm Pt, Ra, Rz – measured quantities (µm)
Length (surface geometry)
At permanent location (S) and outside of it (P) PN-EN ISO 12179:2022-06
5 Contact profilometers Calibration — Length (surface geometry)
Pt: up to 7 µm · CMC 0,04 µm Pt: up to 1000 µm · CMC (0,1 + 0,0005 · Pt) µm Pt: 1 µm to 150 µm · CMC (0,1 + 0,005 · Pt) µm Ra: 0,1 µm to 13 µm · CMC (0,025 + 0,02 · Ra) µm Rz: 1 µm to 52 µm · CMC (0,04 + 0,025 · Rz) µm Pt, Ra, Rz – measured quantities (µm)
Length (surface geometry)
At permanent location (S) and outside of it (P) PN-EN ISO 12179:2022-06
6 Depth measurement standards type A,
Spatial reference artefacts
Calibration — Length (surface geometry)
Pt: up to 7 µm · CMC (0,03 + 0,002 · Pt) µm Pt: up to 1000 µm · CMC (0,1 + 0,0005 · Pt) µm Pt - measured quantity (µm)
Length (surface geometry)
At permanent location (S) PN-EN ISO 5436-1:2002
7 Roughness standards type C and D,
Spatial reference artefacts
Calibration — Length (surface geometry)
Ra, Rq: up to 15 µm · CMC (0,03 + 0,015 · R) µm Rz, Rt, Rp, Rv, Rt, Rmax: up to 1000 µm · CMC (0,04 + 0,02 · R) µm R - measured quantity (µm)
Length (surface geometry)
At permanent location (S) PN-EN ISO 21920-2:2022-06, PN-EN ISO 21920-3:2022-06
8 Non-contact probing systems with optical distance sensors Calibration — Length (coordinate measurements)
25 mm · CMC 1 µm
Length (coordinate measurements)
At permanent location (S) and outside of it (P) PN-EN ISO 10360-8:2014-04
9 Contact touch-trigger probing systems
Contact scanning probing systems
Calibration — Length (coordinate measurements)
25 mm · CMC 0,14 µm
Length (coordinate measurements)
At permanent location (S) and outside of it (P) PN-EN ISO 10360-5:2020
10 Spatial reference artefacts Calibration — Length (coordinate measurements)
up to 1000 mm · CMC (0,6 + 0,7 · L) µm L - wielkość mierzona (m) up to 5000 mm · CMC (1,0 + 1,0 · L) µm L - wielkość mierzona (m)
Length (coordinate measurements)
Internal procedure; At permanent location (S) P2-I1
11 Spatial reference artefacts Calibration — Length (coordinate measurements)
up to 40 m · CMC (0,056 + 0,060 · L) mm L - wielkość mierzona (m)
Length (coordinate measurements)
Internal procedure; At permanent location (S) and outside of it (P) P2-I2
12 Spatial reference artefacts
Optical standards
Calibration — Length (coordinate measurements)
up to 400 mm · CMC (0,6 + 0,5 · L) µm L - wielkość mierzona (m)
Length (coordinate measurements)
Internal procedure; At permanent location (S) P2-I4
13 Spatial reference artefacts Calibration — Length (coordinate measurements)
up to 1000 mm · CMC (1,0 + 3,0 · L) µm L - wielkość mierzona (m) up to 2000 mm · CMC (0,03 + 0,03 · L) mm L - wielkość mierzona (m) up to 5000 mm · CMC (3,0 + 4,0 · L) µm L - wielkość mierzona (m)
Length (coordinate measurements)
Internal procedure; Measurement using Coordinate Measuring Systems; At permanent location (S) P3
14 Spatial reference artefacts Calibration — Length (coordinate measurements)
up to 40 m · CMC (0,1 + 0,1 · L) mm L - wielkość mierzona (m)
Length (coordinate measurements)
Internal procedure; Measurement using Coordinate Measuring Systems; At permanent location (S) and outside of it (P) P3
15 Spatial reference artefacts
Optical standards
Calibration — Length (coordinate measurements)
up to 400 mm · CMC (3,0 + 3,0 · L) µm L - wielkość mierzona (m)
Length (coordinate measurements)
Internal procedure; Measurement using Coordinate Measuring Systems; At permanent location (S) P3
16 Coordinate measuring arms Calibration — Length (coordinate measurements)
100 mm to 5000 mm · CMC (0,001 + 0,001 · L) mm L - measured quantity (m)
Length (coordinate measurements)
At permanent location (S) and outside of it (P) PN-EN ISO 10360-12:2017-02
17 Coordinate Measuring Systems (CMS) with a contact probing system:
Coordinate measuring machines
Calibration — Length (coordinate measurements)
25 mm to 750 mm · CMC Q[0,065; 0,58 L] µm L - measured quantity (m) 20 mm to 6000 mm · CMC (0,0001 + 0,0005 · L) mm L - measured quantity (m)
Length (coordinate measurements)
At permanent location (S) and outside of it (P) PN-EN ISO 10360-2:2010
18 Coordinate Measuring Systems (CMS) with a contact probing system:
Coordinate measuring machines
Coordinate measuring arms
Coordinate tracking systems
(Laser tracker)
Calibration — Length (coordinate measurements)
0,1 m to 24 m · CMC (0,001 + 0,001 · L) mm L - measured quantity (m)
Length (coordinate measurements)
At permanent location (S) and outside of it (P) PN-EN ISO 10360-2:2010
19 Coordinate Measuring Systems (CMS) equipped with imaging probing systems:
Coordinate measuring machines with an optical probing system
Coordinate measuring microscopes
Coordinate measuring projectors
Calibration — Length (coordinate measurements)
1 mm to 1700 mm · CMC (0,0001 + 0,0005 · L) mm L - measured quantity (m)
Length (coordinate measurements)
At permanent location (S) and outside of it (P) PN-EN ISO 10360-7:2011
20 Coordinate Measuring Systems (CMS) with an optical distance sensor:
Coordinate measuring machines
Coordinate measuring arms
Coordinate optical scanners
Calibration — Length (coordinate measurements)
20 mm to 1000 mm · CMC (0,001 + 0,001 · L) mm L - measured quantity (m)
Length (coordinate measurements)
At permanent location (S) and outside of it (P) VDI/VDE 2634 Blatt 2:2012, Blatt 3:2008
21 Coordinate Measuring Systems (CMS) with an optical distance sensor:
Coordinate measuring machines
Coordinate measuring arms
Coordinate optical scanners
Calibration — Length (coordinate measurements)
20 mm to 10000 mm · CMC (0,001 + 0,001 · L) mm L - measured quantity (m)
Length (coordinate measurements)
At permanent location (S) and outside of it (P) PN-EN ISO 10360-8:2014-04
22 Coordinate Measuring Systems (CMS): Optical 3D CMS
Coordinate optical scanners
Calibration — Length (coordinate measurements)
20 mm to 10000 mm · CMC (1,0 + 1,0 · L) mm L - measured quantity (m)
Length (coordinate measurements)
At permanent location (S) and outside of it (P) PN-EN ISO 10360-13:2022-02
23 Coordinate Measuring Systems
Industrial computed tomography systems
Calibration — Length (coordinate measurements)
10 mm to 1000 mm · CMC (1,0 + 1,0 · L) µm L - measured quantity (m)
Length (coordinate measurements)
At permanent location (S) and outside of it (P) VDI/VDE 2630 Blatt 1.3:2011

Reference standards (18)

P2-I1
P2-I2
P2-I3
P2-I4
P3
PN-EN ISO 10360-12:2017-02
PN-EN ISO 10360-13:2022-02
PN-EN ISO 10360-2:2010
PN-EN ISO 10360-5:2020
PN-EN ISO 10360-7:2011
PN-EN ISO 10360-8:2014-04
PN-EN ISO 12179:2022-06
PN-EN ISO 15530-3:2011
PN-EN ISO 21920-2:2022-06
PN-EN ISO 21920-3:2022-06
PN-EN ISO 5436-1:2002
VDI/VDE 2630 Blatt 1.3:2011
VDI/VDE 2634 Blatt 2:2012, Blatt 3:2008

The same scope as data (JSON): https://labcoda.pl/api/accreditation-scopes/labs/PL/AP%20132