🇵🇱 BAJOR METROLOGY Piotr Bajor PL

PCA AP 195 • Złotów, Poland • 30 calibration items

Metrology & calibration

BAJOR METROLOGY Piotr Bajor is a calibration laboratory accredited by PCA under number AP 195 (Złotów, Poland). Its accreditation scope covers 30 calibration items in the following areas: Metrology & calibration. Calibrated items include: - resolution 0.001 mm, - scale interval 0.01 mm, Gauge blocks (classes 0, 1, 2), Plain plug gauges. Most frequently used calibration principles: Internal procedure; Method using gauge blocks; At permanent locatio…, Internal procedure; Method using OPTIMAR 100; At permanent location…, Internal procedure; Comparison method using a rigid rule; At perman….

At a glance

  • Accreditation number: PCA AP 195
  • Calibration items in scope: 30
  • Types of calibrated items: 34
  • Calibration principles used: 19
  • City: Złotów, Poland
  • Valid until: 08-06-2029
Accreditation number
AP 195
Accreditation body
PCA
Address
ul. Bohaterów Westerplatte 1H, 77-400 Złotów
City
Złotów, Poland
Division
Calibration Laboratory
Valid until
08-06-2029

What this laboratory calibrates (34)

Calibration principles (19)

Certificate information

Issue date
23.04.2026
Issue no.
7
Certificate date
04.04.2025
Accreditation cycle
23.05.2025 — 08.06.2029
Approved by
Katarzyna Wiśniewska

Accreditation scope — calibration items (30)

The uncertainty covered by the CMC is the expanded uncertainty with a coverage probability of approximately 95 %. The CMC uncertainty is expressed in measurand units. A CMC uncertainty value expressed as the equation Q[a; b] denotes the root sum of squares of the terms in brackets: Q[a; b] = (a² + b²)^1/2.

No. Calibrated quantity / subject of calibration Nominal range / parameters / CMC Calibration principle Calibration procedure
Calibration items
1 Analogue dial indicators with scale interval Calibration — Length
- 0.01 mm — 0 mm to 50 mm · CMC 1,0 µm - 0.01 mm — 0 mm to 100 mm · CMC 1,2 µm - 0.001 mm — 0 mm to 5 mm · CMC 0,74 µm
Length
Internal procedure; Method using OPTIMAR 100; At permanent location (S) IW-11.1-BM
2 Lever-type dial test indicators with scale interval Calibration — Length
- 0.01 mm — -1.6 mm to 1,6 mm · CMC 1,0 µm - 0.002 mm — -0,6 mm to 0,6 mm · CMC 0,74 µm - 0.001 mm — -0,14 mm to 0,14 mm · CMC 0,74 µm
Length
Internal procedure; Method using OPTIMAR 100; At permanent location (S) IW-11.3-BM
3 Digital indicators with resolution Calibration — Length
- 0.01 mm — 0 mm to 50,8 mm · CMC 1,0 µm - 0.001 mm — 0 mm to 50,8 mm · CMC 0,74 µm - 0.0005 mm — 0 mm to 50,8 mm · CMC 0,74 µm
Length
Internal procedure; Method using OPTIMAR 100; At permanent location (S) IW-11.1-BM
4 Vernier depth gauges Calibration — Length
- resolution 0,01 mm — 0 mm to 500 mm · CMC Q[0,014; 0,054·L] mm - scale interval 0,02 and 0,05 mm — 0 mm to 500 mm · CMC Q[0,017; 0,054·L] mm - scale interval 0,1 mm — 0 mm to 500 mm · CMC Q[0,027; 0,094·L] mm
Length
Internal procedure; Method using gauge blocks; At permanent location (S) IW-9.2-BM
5 Dial thickness gauges Calibration — Length
- resolution 0,001 mm — 0 mm to 50 mm · CMC 1 µm - resolution 0,005 mm — 0 mm to 50 mm · CMC 3 µm - resolution 0,01 mm — 0 mm to 50 mm · CMC 0,01 mm - scale interval 0,001, 0,005 and 0,01 mm — 0 mm to 50 mm · CMC 1 µm - scale interval 0,1 mm — 0 mm to 50 mm · CMC 6 µm
Length
Internal procedure; Method using gauge blocks; At permanent location (S) IW-12.1-BM
6 Dial callipers (internal/external) Calibration — Length
- resolution 0,001 mm — 0 mm to 50 mm · CMC 2 µm - resolution 0,005 mm — 0 mm to 50 mm · CMC 3 µm - resolution 0,01 mm — 0 mm to 50 mm · CMC 0,01 mm - scale interval 0,001, 0,005 and 0,01 mm — 0 mm to 50 mm · CMC 4 µm - scale interval 0,1 mm — 0 mm to 50 mm · CMC 6 µm
Length
Internal procedure; Method using gauge blocks; At permanent location (S) IW-12.1-BM based on VDI/VDE/DGQ 2618 Blatt 12.1:2005-02
7 Internal micrometers
- resolution 0.001 mm
- scale interval 0.01 mm
Calibration — Length
5 mm to 100 mm · CMC Q[1,8; 11,2·L] µm
Length
Internal procedure; Comparison method using gauge blocks; At permanent location (S) IW-10.7-BM
8 External micrometers Calibration — Length
- scale interval 0,01 mm — 0 mm to 600 mm · CMC Q[1,28; 14 L] µm - resolution 0,001 mm — 0 mm to 600 mm · CMC Q[0,78; 14·L] µm - resolution 0,0001 mm — 0 mm to 25 mm · CMC 0,6 µm
Length
Internal procedure; Method using gauge blocks; At permanent location (S) IW-10.1-BM
9 Gauge blocks (classes 0, 1, 2) Calibration — Length
0,5 mm to 100 mm · CMC Q[0,052; 0,0014·L] µm
Length
Internal procedure; Method using class K gauge blocks as reference; At permanent location (S) IW-3.1-BM based on PN-EN ISO 3650:2000P
10 Gauge blocks (classes 0, 1, 2) Calibration — Length
0,5 mm to 150 mm · CMC Q[0,074; 0,0018·L] µm
Length
Internal procedure; Method using class 0 gauge blocks as reference; At permanent location (S) IW-3.1-BM based on PN-EN ISO 3650:2000P
11 Setting rings Calibration — Length
2 mm to 150 mm · CMC Q[0,8; 5·L] µm
Length
Internal procedure; Comparison method using a length measuring machine and setting rings; At permanent location (S) IW-4.1-BM
12 Rigid rules Calibration — Length
0 mm to 5000 mm · CMC Q[0,097; 0,012·L] mm
Length
Internal procedure; Comparison method using a semi-rigid rule; At permanent location (S) IW-32.1-BM
13 Semi-rigid rules Calibration — Length
0 mm to 5000 mm · CMC Q[0,097; 0,012·L] mm
Length
Internal procedure; Comparison method using a rigid rule; At permanent location (S) IW-32.1-BM
14 Tape measures Calibration — Length
0 mm to 5000 mm · CMC Q[0,097; 0,012·L] mm
Length
Internal procedure; Comparison method using a rigid rule; At permanent location (S) IW-32.1-BM
15 Cylindrical thread ring gauges Calibration — Length
2,5 mm to 150 mm · CMC 3,5 µm
Length
Internal procedure; Method using a length measuring machine and setting rings; At permanent location (S) IW-4.9-BM
16 Cylindrical thread plug gauges Calibration — Length
2 mm to 100 mm · CMC 3,2 µm
Length
Internal procedure; Method using a length measuring machine and measuring wires; At permanent location (S) IW-4.8-BM based on VDI/VDE/DGQ 2618 Blatt 4.8:2006-04
17 Plain plug gauges Calibration — Length
1 mm to 150 mm · CMC Q[0,9; 8·L] µm
Length
Internal procedure; Method using a length measuring machine; At permanent location (S) IW-4.1-BM
18 Plain plug gauges Calibration — Length
1 mm to 25 mm · CMC 1,0 µm
Length
Internal procedure; Method using a micrometer with 0.1 µm resolution; At permanent location (S) IW-4.1-BM
19 Vernier callipers Calibration — Length
- resolution 0,01 mm — 0 mm to 1000 mm · CMC Q[0,014; 0,047·L] mm - scale interval 0,02 and 0,05 mm — 0 mm to 1000 mm · CMC Q[0,017; 0,047·L] mm - scale interval 0,1 mm — 0 mm to 1000 mm · CMC Q[0,027; 0,047·L] mm
Length
Internal procedure; Method using gauge blocks; At permanent location (S) IW-9.1-BM
20 Leaf feeler gauges Calibration — Length
0,02 mm to 2,00 mm · CMC 1,6 µm
Length
Internal procedure; Method using a micrometer; At permanent location (S) IW-31.1-BM
21 Two-point expanding dial bore gauges
- resolution 0.001 mm
- resolution 0.01 mm
Calibration — Length
0,95 mm to 18 mm · CMC 2 µm
Length
Internal procedure; Method using gauge blocks or a micrometer; At permanent location (S) IW-13.2-BM
22 Lever-type dial bore gauges with indicator scale interval Calibration — Length
- 0.01 mm — 18 mm to 600 mm · CMC 1,1 µm - 0.001 mm — 18 mm to 600 mm · CMC 0,81 µm
Length
Internal procedure; Method using OPTIMAR 100; At permanent location (S) IW-13.2-BM
23 Two-point inside micrometers
- resolution 0.001 mm
- scale interval 0.01 mm
Calibration — Length
50 mm to 1500 mm · CMC Q[1,8; 11,2·L] µm
Length
Internal procedure; Comparison method using gauge blocks; At permanent location (S) IW-10.7-BM
24 Three-point inside micrometers
- resolution 0.001; 0.005 mm
Calibration — Length
6 mm to 150 mm · CMC Q[1,8; 14,2·L] µm
Length
Internal procedure; Method using setting rings; At permanent location (S) IW-10.8-BM
25 Measuring wires Calibration — Length
0,1 mm to 25 mm · CMC 1,0 µm
Length
Internal procedure; Method using a micrometer with 0.1 µm resolution; At permanent location (S) IW-4.1-BM
26 Vernier height gauges Calibration — Length
- resolution 0,01 mm — 0 mm to 1000 mm · CMC Q[0,014; 0,047·L] mm - scale interval 0,02 and 0,05 mm — 0 mm to 1000 mm · CMC Q[0,017; 0,047·L] mm - scale interval 0,1 mm — 0 mm to 1000 mm · CMC Q[0,027; 0,047·L] mm
Length
Internal procedure; Method using gauge blocks; At permanent location (S) IW-9.3-BM
27 Radius gauges Calibration — Length
0,1 mm to 25 mm · CMC 0,01 mm
Length
Internal procedure; Direct method using an ISD-V150A measuring microscope; At permanent location (S) IW-34.1-BM
28 Setting standards for external dimensions Calibration — Length
25 mm to 575 mm · CMC Q[1,1; 5,23·L] µm
Length
Internal procedure; Comparison method using a length measuring machine; At permanent location (S) IW-10.1-BM
29 Universal protractors and digital protractors
- resolution 1’
- scale interval 5’
Calibration — Angle
0° to 360° · CMC 2’
Angle
Internal procedure; Comparison method using angle gauge blocks; At permanent location (S) IW-7.2-BM
30 90° try squares Calibration — Angle
arm length up to 315 mm · CMC 3 µm
Angle
Internal procedure; Comparison method using a cylindrical square and gauge blocks; At permanent location (S) IW-7.1-BM

Reference standards (22)

IW-10.1-BM
IW-10.7-BM
IW-10.8-BM
IW-11.1-BM
IW-11.3-BM
IW-12.1-BM
IW-13.2-BM
IW-3.1-BM
IW-31.1-BM
IW-32.1-BM
IW-34.1-BM
IW-4.1-BM
IW-4.8-BM
IW-4.9-BM
IW-7.1-BM
IW-7.2-BM
IW-9.1-BM
IW-9.2-BM
IW-9.3-BM
PN-EN ISO 3650:2000P
VDI/VDE/DGQ 2618 Blatt 12.1:2005-02
VDI/VDE/DGQ 2618 Blatt 4.8:2006-04

The same scope as data (JSON): https://labcoda.pl/api/accreditation-scopes/labs/PL/AP%20195