🇵🇱 MIKRO POMIAR Mariusz Pałucki PL

PCA AP 141 • Łęgowo, Poland • 52 calibration items

Metrology & calibration

MIKRO POMIAR Mariusz Pałucki is a calibration laboratory accredited by PCA under number AP 141 (Łęgowo, Poland). Its accreditation scope covers 52 calibration items in the following areas: Metrology & calibration. Calibrated items include: Analogue dial indicators with scale interval:, Dial bore gauges, Digital indicators with resolution:, Gauge blocks (classes 0, 1, 2). Most frequently used calibration principles: Internal procedure; Calibration using a horizontal Abbe length meas…, Internal procedure; Calibration using gauge blocks; At permanent lo…, Internal procedure; At permanent location (S).

At a glance

  • Accreditation number: PCA AP 141
  • Calibration items in scope: 52
  • Types of calibrated items: 51
  • Calibration principles used: 19
  • City: Łęgowo, Poland
  • Valid until: 17-11-2027
Accreditation number
AP 141
Accreditation body
PCA
Address
Różyny ul. Gdańska 45, 80-031 Łęgowo
City
Łęgowo, Poland
Division
MIKRO POMIAR Mariusz Pałucki Calibration Laboratory
Valid until
17-11-2027

What this laboratory calibrates (51)

Calibration principles (19)

Certificate information

Issue date
18.12.2024
Issue no.
14
Certificate date
15.03.2023
Accreditation cycle
16.11.2023 — 17.11.2027
Approved by
Tadeusz Matras

Accreditation scope — calibration items (52)

The uncertainty covered by the CMC is the expanded uncertainty with a coverage probability of approximately 95 %. The CMC uncertainty is expressed in measurand units

No. Calibrated quantity / subject of calibration Nominal range / parameters / CMC Calibration principle Calibration procedure
Calibration items
1 Analogue lever-type dial test indicators Calibration — Length
scale interval: 0,01 mm — -1,6 mm to 1,6 mm · CMC 3,5 µm scale interval: 0,002 mm — -1,6 mm to 1,6 mm · CMC 1,2 µm scale interval: 0,001 mm — -1,6 mm to 1,6 mm · CMC 1,2 µm
Length
Internal procedure; At permanent location (S) PP/S02/08 based on VDI/VDE/DGQ 2618:11.2
2 Digital lever-type test indicators Calibration — Length
resolution: 0,001 mm — -2,0 mm to 2,0 mm · CMC 1,8 µm resolution: 0,01 mm — -2,0 mm to 2,0 mm · CMC 11,6 µm
Length
Internal procedure; At permanent location (S) PP/S02/08 based on VDI/VDE/DGQ 2618:11.2
3 Analogue dial indicators with scale interval:
0,1 mm
0,02 mm
0,01 mm
0,001 mm
0,005 mm
Calibration — Length
0 mm to 100 mm · CMC 20 µm 0 mm to 100 mm · CMC 20 µm 0 mm to 100 mm · CMC 3,7 µm 0 mm to 5 mm · CMC 0,8 µm 0 mm to 100 mm · CMC 3,7 µm
Length
Internal procedure; At permanent location (S) PP/S02/09 based on VDI/VDE/DGQ 2618:11.1
4 Analogue dial indicators with scale interval: Calibration — Length
scale interval: 0,01 mm — 0 mm to 50 mm · CMC 5,4 µm
Length
Internal procedure; Calibration using a micrometer head; Outside of permanent location (P) PP/S02/09
5 Digital indicators with resolution: Calibration — Length
resolution: 0,01 mm — 0 mm to 100 mm · CMC 11,6 µm resolution: 0,001 mm — 0 mm to 100 mm · CMC 1,8 µm resolution: 0,002 mm — 0 mm to 100 mm · CMC 11,6 µm resolution: 0,0001 mm — 0 mm to 25 mm · CMC 0,4 µm resolution: 0,0001 mm — 0 mm to 50 mm · CMC 0,5 µm resolution: 0,0001 mm — 0 mm to 100 mm · CMC 0,7 µm resolution: 0,0005 mm — 0 mm to 30 mm · CMC 0,5 µm resolution: 0,0005 mm — 30 mm to 60 mm · CMC 0,6 µm resolution: 0,0005 mm — 60 mm to 100 mm · CMC 0,8 µm
Length
Internal procedure; At permanent location (S) PP/S02/09 based on VDI/VDE/DGQ 2618:11.4
6 Digital indicators with resolution: Calibration — Length
resolution: 0,01 mm — 0 mm to 50 mm · CMC 11,6 µm
Length
Internal procedure; Calibration using a micrometer head; Outside of permanent location (P) PP/S02/09
7 Vertical Abbe length measuring machines Calibration — Length
0 mm to 100 mm · CMC (1,5 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using gauge blocks; At permanent location (S) and outside of it (P) PP/S04/03
8 Horizontal Abbe length measuring machines Calibration — Length
0 mm to 3000 mm · CMC (0,1 + 1,5 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using gauge blocks and a laser interferometer; At permanent location (S) and outside of it (P) PP/S04/03
9 Horizontal length measuring machines (1D machines) Calibration — Length
0 mm to 3000 mm · CMC (0,1 + 1,5 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using gauge blocks and a laser interferometer; At permanent location (S) and outside of it (P) PP/S04/03
10 Reference foils Calibration — Length
10 µm to 100 µm · CMC 0,7 µm 100 µm to 200 µm · CMC 1,2 µm 200 µm to 500 µm · CMC 2,3 µm 500 µm to 1200 µm · CMC 3,5 µm 1200 µm to 2000 µm · CMC 3,6 µm
Length
Internal procedure; Calibration using a horizontal Abbe length measuring machine; At permanent location (S) PP/S02/17
11 Micrometer depth gauges Calibration — Length
0 mm to 300 mm · CMC (1,1 + 20 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using gauge blocks; At permanent location (S) PP/S02/02
12 Micrometer heads Calibration — Length
0 mm to 50 mm · CMC (1,1 + 20 · L) µm; L – wielkość mierzona (m)
Length
Internal procedure; Calibration using a horizontal Abbe length measuring machine; At permanent location (S) PP/S02/01
13 Vernier depth gauges Calibration — Length
0 mm to 500 mm · CMC (28 + 15 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using gauge blocks; At permanent location (S) and outside of it (P) PP/S02/05
14 Gauge block comparators Calibration — Length
0 mm to 100 mm · CMC 0,033 µm
Length
Internal procedure; At permanent location (S) and outside of it (P) PP/S04/07 based on EURAMET/cg-2/v/2.0
15 Universal measuring microscopes Calibration — Length
0 mm to 400 mm · CMC (0,9 + 8 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using glass standards; At permanent location (S) and outside of it (P) PP/S04/04
16 Workshop measuring microscopes Calibration — Length
0 mm to 400 mm · CMC (0,9 + 8 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using glass standards; At permanent location (S) and outside of it (P) PP/S04/04
17 Inside micrometers Calibration — Length
5 mm to 100 mm · CMC (1,1 + 20 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using gauge blocks; At permanent location (S) PP/S02/14
18 Outside micrometers Calibration — Length
0 mm to 1600 mm · CMC (1,1 + 20 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using gauge blocks; At permanent location (S) PP/S02/01
19 Indicating micrometers Calibration — Length
0 mm to 150 mm · CMC (0,7 + 10 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using gauge blocks; At permanent location (S) PP/S02/11
20 Setting rings Calibration — Length
1 mm to 250 mm · CMC (0,71 + 4,2 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using a horizontal Abbe length measuring machine and a setting ring; At permanent location (S) PP/S02/10
21 Gauge blocks (classes 0, 1, 2) Calibration — Length
0,5 mm to 100 mm · CMC (0,05 + 0,8 · L) µm; L – measured value (m)
Length
Internal procedure; At permanent location (S) PP/S01/01 based on PN-EN ISO 3650:2000
22 Gauge blocks (classes 0, 1, 2) Calibration — Length
100 mm to 1000 mm · CMC (0,05 + 0,8 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using a gauge block calibration station; At permanent location (S) PP/S01/01
23 Profile projectors Calibration — Length
0 mm to 450 mm · CMC (0,9 + 8 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using glass standards; At permanent location (S) and outside of it (P) PP/S04/02
24 Parallel thread ring gauges Calibration — Length
3,5 mm to 200 mm · CMC (3,5 + 10 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using a horizontal Abbe length measuring machine; At permanent location (S) PP/S02/12
25 Plain plug gauges Calibration — Length
0,5 mm to 200 mm · CMC (0,7 + 3 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using a horizontal Abbe length measuring machine; At permanent location (S) PP/S02/12
26 Parallel thread plug gauges Calibration — Length
1 mm to 200 mm · CMC (3 + 10 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using a horizontal Abbe length measuring machine; At permanent location (S) PP/S02/12
27 Special gauges Calibration — Length
0,1 mm to 200 mm · CMC 0,3 µm
Length
Internal procedure; Calibration using a horizontal Abbe length measuring machine; At permanent location (S) PP/S02/12
28 Vernier callipers Calibration — Length
0 mm to 3200 mm · CMC (28 + 15 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using gauge blocks; At permanent location (S) PP/S02/03
29 Feeler gauges Calibration — Length
0,02 mm to 2 mm · CMC 0,3 µm
Length
Internal procedure; Calibration using a horizontal Abbe length measuring machine; At permanent location (S) PP/S02/16
30 Dial bore gauges Calibration — Length
1,5 mm to 500 mm · CMC 3,4 µm
Length
Internal procedure; Calibration using gauge blocks; At permanent location (S) PP/S02/06
31 Dial bore gauges Calibration — Length
4 mm to 500 mm · CMC 3,9 µm
Length
Internal procedure; Calibration using a micrometer head; At permanent location (S) PP/S02/06
32 Two-point inside micrometers Calibration — Length
0 mm to 3000 mm · CMC (4 + L/0,075) µm; L – measured value (m)
Length
Internal procedure; Calibration using an optical horizontal length measuring machine (1D machine); At permanent location (S) PP/S03/01
33 Two-point inside micrometers Calibration — Length
0 mm to 200 mm · CMC (0,23 + 0,5 · L) µm; L – wielkość mierzona (m) 200 mm do 3000 mm · CMC (0,13 + 0,95 · L) µm; L – wielkość mierzona (m)
Length
Internal procedure; Calibration using a horizontal length measuring machine (1D machine) with an interferometric system; At permanent location (S) PP/S03/01
34 Three-point inside micrometers Calibration — Length
2 mm to 200 mm · CMC 3,5 µm
Length
Internal procedure; Calibration using setting rings; At permanent location (S) PP/S02/07
35 Indicating snap gauges Calibration — Length
0 mm to 100 mm · CMC (0,7 + 10 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using gauge blocks; At permanent location (S) PP/S02/11
36 Measuring wires Calibration — Length
0,1 mm to 200 mm · CMC 0,3 µm
Length
Internal procedure; Calibration using a horizontal Abbe length measuring machine; At permanent location (S) PP/S02/12
37 Vernier height gauges Calibration — Length
0 mm to 1500 mm · CMC (28 + 15 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using gauge blocks; At permanent location (S) and outside of it (P) PP/S02/04
38 Digital height gauges with resolution: Calibration — Length
resolution: 0,010 mm — 0 mm to 1500 mm · CMC 10,8 µm resolution: 0,005 mm — 0 mm to 1500 mm · CMC 7,5 µm resolution: 0,001 mm — 0 mm to 1500 mm · CMC (1,14 + 0,27 · L) µm; L – measured value (m) resolution: 0,0005 mm — 0 mm to 1500 mm · CMC (0,57 + 0,48 · L) µm; L – measured value (m) resolution: 0,0001 mm — 0 mm to 1500 mm · CMC (0,26 + 2,11 · L) µm; L – measured value (m)
Length
Internal procedure; At permanent location (S) and outside of it (P) PP/S04/05 based on VDI_VDE_DGQ 2618-16.1
39 Setting standards for internal dimensions Calibration — Length
0 mm to 160 mm · CMC 0,95 µm 160 mm to 600 mm · CMC 1,25 µm
Length
Internal procedure; Calibration using a horizontal length measuring machine (1D machine) with an interferometric system; At permanent location (S) PP/S03/01
40 Setting standards for external dimensions Calibration — Length
0 mm to 1000 mm · CMC (4 + L/0,075) µm; L – wielkość mierzona (m)
Length
Internal procedure; Calibration using an optical horizontal length measuring machine (1D machine); At permanent location (S) PP/S03/02
41 Setting standards for external dimensions Calibration — Length
0 mm to 200 mm · CMC (0,23 + 0,5 · L) µm; L – wielkość mierzona (m) 200 mm do 1600 mm · CMC (0,13 + 0,95 · L) µm; L – wielkość mierzona (m)
Length
Internal procedure; Calibration using a horizontal length measuring machine (1D machine) with an interferometric system; At permanent location (S) PP/S03/02
42 Measuring magnifiers Calibration — Length
0 mm to 20 mm · CMC (24 + 8 · L) µm; L – measured value (m)
Length
Internal procedure; Calibration using line standards; At permanent location (S) and outside of it (P) PP/S04/04
43 90° try squares Calibration — Angle
40 mm to 1000 mm · CMC 4,0 µm
Angle
Internal procedure; Calibration using gauge blocks; At permanent location (S) PP/S02/15
44 Universal measuring microscopes Calibration — Angle
0° to 360° · CMC 2ʹ
Angle
Internal procedure; Calibration using angle gauge blocks; At permanent location (S) and outside of it (P) PP/S04/04
45 Workshop measuring microscopes Calibration — Angle
0° to 360° · CMC 2ʹ
Angle
Internal procedure; Calibration using angle gauge blocks; At permanent location (S) and outside of it (P) PP/S04/04
46 Profile projectors Calibration — Angle
0° to 360° · CMC 2ʹ
Angle
Internal procedure; Calibration using angle gauge blocks; At permanent location (S) and outside of it (P) PP/S04/02
47 Straightedges Calibration — Length (surface geometry)
250 mm to 3000 mm · CMC (1,6 + 0,3 · L) µm; L – measured value (m)
Length (surface geometry)
Internal procedure; Calibration using a set of differential levels; At permanent location (S) and outside of it (P) PP/S04/01
48 Surface plates Calibration — Length (surface geometry)
(250 x 250) mm to (2000 x 2500) mm · CMC (1,6 + 0,3 · L) µm; L – measured value (m)
Length (surface geometry)
Internal procedure; Calibration using a set of differential levels; At permanent location (S) and outside of it (P) PP/S04/01
49 Touch-trigger contact probing systems Calibration — Length (coordinate measurements)
25 mm · CMC 0,6 µm
Length (coordinate measurements)
Internal procedure; Outside of permanent location (P) PP/S04/06 PP/S04/11 based on PN-EN ISO 10360-5:2020
50 Scanning contact probing systems Calibration — Length (coordinate measurements)
25 mm · CMC 0,6 µm
Length (coordinate measurements)
Internal procedure; Outside of permanent location (P) PP/S04/09 based on PN-EN ISO 10360-5:2020
51 Coordinate measuring machines Calibration — Length (coordinate measurements)
300 mm to 2272 mm · CMC (0,2 + 0,52 · L) µm; L – measured value (m)
Length (coordinate measurements)
Internal procedure; Outside of permanent location (P) PP/S04/06 PP/S04/09 PP/S04/11 based on PN-EN ISO 10360-2:2010
52 Coordinate Measuring Systems (CMS) with an optical imaging probing system:
- coordinate measuring machines with an optical probing system
- coordinate measuring microscopes
- coordinate measuring projectors
Calibration — Length (coordinate measurements)
0,1 mm to 1336 mm · CMC (0,5 + 1,29 · L) µm; L – measured value (m)
Length (coordinate measurements)
Internal procedure; Calibration using glass standards; Outside of permanent location (P) PP/S04/10

Reference standards (37)

EURAMET/cg-2/v/2.0
PN-EN ISO 10360-2:2010
PN-EN ISO 10360-5:2020
PN-EN ISO 3650:2000
PP/S01/01
PP/S02/01
PP/S02/02
PP/S02/03
PP/S02/04
PP/S02/05
PP/S02/06
PP/S02/07
PP/S02/08
PP/S02/09
PP/S02/10
PP/S02/11
PP/S02/12
PP/S02/14
PP/S02/15
PP/S02/16
PP/S02/17
PP/S03/01
PP/S03/02
PP/S04/01
PP/S04/02
PP/S04/03
PP/S04/04
PP/S04/05
PP/S04/06
PP/S04/07
PP/S04/09
PP/S04/10
PP/S04/11
VDI/VDE/DGQ 2618:11.1
VDI/VDE/DGQ 2618:11.2
VDI/VDE/DGQ 2618:11.4
VDI_VDE_DGQ 2618-16.1

The same scope as data (JSON): https://labcoda.pl/api/accreditation-scopes/labs/PL/AP%20141