🇵🇱 Laboratorium Pomiarowe MUTECH Sp. z o.o. Sp.k. PL

PCA AP 106 • Łowicz, Poland • 50 calibration items

Metrology & calibration

Laboratorium Pomiarowe MUTECH Sp. z o.o. Sp.k. is a calibration laboratory accredited by PCA under number AP 106 (Łowicz, Poland). Its accreditation scope covers 50 calibration items in the following areas: Metrology & calibration. Calibrated items include: Analogue dial gauges with a scale interval of 0,01 mm, Anemometers, Bourdon tube pressure gauges, Bourdon tube pressure gauges (barometers). Most frequently used calibration principles: Internal procedure; At permanent location (S), Internal procedure; At permanent location (S) and outside of it (P), Internal procedure; Calibration with the PRECIMAR 100 instrument; A….

At a glance

  • Accreditation number: PCA AP 106
  • Calibration items in scope: 50
  • Types of calibrated items: 53
  • Calibration principles used: 10
  • City: Łowicz, Poland
  • Valid until: 09-08-2027
Accreditation number
AP 106
Accreditation body
PCA
Address
Pl. Nowy Rynek 26, 99-400 Łowicz
City
Łowicz, Poland
Valid until
09-08-2027

What this laboratory calibrates (53)

Calibration principles (10)

Certificate information

Issue date
12.06.2026
Issue no.
25
Certificate date
14.07.2020
Accreditation cycle
11.07.2023 — 09.08.2027
Approved by
Katarzyna Wiśniewska

Accreditation scope — calibration items (50)

The uncertainty covered by the CMC is the expanded uncertainty with a coverage probability of approximately 95 % and is expressed in measurand units. A CMC uncertainty value expressed as a percentage is the relative measurement uncertainty and refers to the percentage of the value of the measurand.

No. Calibrated quantity / subject of calibration Nominal range / parameters / CMC Calibration principle Calibration procedure
Calibration items
1 Breath analysers Calibration — Mass concentration (breath analysis)
0,00 mg/l do 0,40 mg/l · CMC 0,01 mg/l 0,41 mg/l do 1,00 mg/l · CMC 0,02 mg/l 1,01 mg/l to 1,50 mg/l · CMC 0,03 mg/l 1,51 mg/l to 2,00 mg/l · CMC 0,05 mg/l
Mass concentration (breath analysis)
Internal procedure; mass concentration of ethanol in exhaled air (mg of ethanol per 1 l of air); At permanent location (S) Internal procedure PA-F-02 based on OIML R126-2:2021 A.1.1, A.2
2 Gauge blocks (classes 1, 2) Calibration — Length
0,5 mm to 100 mm · CMC 0,092 + 1,2 · L
Length
Internal procedure; At permanent location (S) Internal procedure PA-M-08
3 Vernier calipers Calibration — Length
0 mm to 200 mm · CMC 10 µm 0 mm do 500 mm · CMC 15 µm 0 mm to 1000 mm · CMC 30 µm
Length
Internal procedure; At permanent location (S) Internal procedure PA-M-01
4 Vernier depth gauges Calibration — Length
0 mm to 300 mm · CMC 12 µm
Length
Internal procedure; At permanent location (S) Internal procedure PA-M-02
5 Vernier height gauges Calibration — Length
0 mm to 500 mm · CMC 15 µm
Length
Internal procedure; At permanent location (S) Internal procedure PA-M-03
6 External micrometers Calibration — Length
0 mm to 25 mm · CMC 2 µm 25 mm to 50 mm · CMC 2 µm 50 mm to 75 mm · CMC 2 µm 75 mm to 100 mm · CMC 3 µm 100 mm to 125 mm · CMC 3 µm 125 mm to 150 mm · CMC 3 µm 150 mm to 175 mm · CMC 4 µm 175 mm to 200 mm · CMC 4 µm
Length
Internal procedure; At permanent location (S) Internal procedure PA-M-04
7 Micrometer depth gauges Calibration — Length
0 mm to 25 mm · CMC 2 µm 25 mm to 50 mm · CMC 2 µm 50 mm to 75 mm · CMC 3 µm 75 mm to 100 mm · CMC 3 µm
Length
Internal procedure; At permanent location (S) Internal procedure PA-M-05
8 Analogue dial gauges with a scale interval of 0,01 mm Calibration — Length
0 mm to 50 mm · CMC 4 µm
Length
Internal procedure; Calibration with a micrometer head; At permanent location (S) Internal procedure PA-M-06
9 Digital dial gauges with resolution Calibration — Length
- 0,001 mm — 0 mm to 50,8 mm · CMC 3 µm - 0,01 mm — 0 mm to 50,8 mm · CMC 3 µm
Length
Internal procedure; Calibration with a micrometer head; At permanent location (S) Internal procedure PA-M-06
10 Analogue dial gauges with a scale interval of 0,01 mm Calibration — Length
up to 10 mm · CMC 1,2 µm 10 mm do 30 mm · CMC 1,7 µm 30 mm do 50 mm · CMC 2,3 µm 50 mm do 100 mm · CMC 4,1 µm
Length
Internal procedure; Calibration with the PRECIMAR 100 instrument; At permanent location (S) Internal procedure PA-M-15
11 Analogue dial gauges with a scale interval of 0,001 mm Calibration — Length
0 mm to 5 mm · CMC 1,0 µm
Length
Internal procedure; Calibration with the PRECIMAR 100 instrument; At permanent location (S) Internal procedure PA-M-15
12 Digital dial gauges with a resolution of 0,01 mm Calibration — Length
up to 12,7 mm · CMC 2,7 µm 12,7 mm to 25,4 mm · CMC 3,0 µm 25,4 mm to 50,8 mm · CMC 3,3 µm 50,8 mm to 100 mm · CMC 4,7 µm
Length
Internal procedure; Calibration with the PRECIMAR 100 instrument; At permanent location (S) Internal procedure PA-M-15
13 Digital dial gauges with a resolution of (0,001; 0,0005) mm Calibration — Length
up to 12,7 mm · CMC 1,2 µm 12,7 mm to 25,4 mm · CMC 1,5 µm 25,4 mm to 50,8 mm · CMC 2,3 µm 50,8 mm to 100 mm · CMC 4,0 µm
Length
Internal procedure; Calibration with the PRECIMAR 100 instrument; At permanent location (S) Internal procedure PA-M-15
14 Rigid rules Calibration — Length
0 m to 1 m · CMC Q[0,12; 0,02 · L] mm
Length
Internal procedure; At permanent location (S) Internal procedure PA-M-07
15 Semi-rigid rules Calibration — Length
0 m to 5 m · CMC Q[0,12; 0,02 · L] mm
Length
Internal procedure; At permanent location (S) Internal procedure PA-M-07
16 Measuring tapes Calibration — Length
0 m to 5 m · CMC Q[0,12; 0,02 · L] mm
Length
Internal procedure; At permanent location (S) Internal procedure PA-M-07
17 Dial thickness gauges: Calibration — Length
- with a scale interval of 0,01 mm; with a resolution of 0,001 mm — 0 mm to 12 mm · CMC 3 µm - with a resolution of 0,01 mm — 0 mm to 12 mm · CMC 5 µm
Length
Internal procedure; At permanent location (S) Internal procedure PA-M-10
18 Digital weld gauges Calibration — Length
- measurement of welds on a flat surface — 0 mm to 10 mm · CMC 10 µm - measurement of fillet welds — 0 mm to 10 mm · CMC 16 µm
Length
Internal procedure; At permanent location (S) Internal procedure PA-M-11
19 Analogue weld gauges Calibration — Length
- measurement of welds on a flat surface — 0 mm to 10 mm · CMC 70 µm - measurement of fillet welds — 0 mm to 10 mm · CMC 80 µm
Length
Internal procedure; At permanent location (S) Internal procedure PA-M-11
20 Setting rings using contact arms Calibration — Length
15 mm to 50 mm · CMC 1,6 µm 50 mm to 100 mm · CMC 2,0 µm
Length
Internal procedure; Direct method using the ULM 520 S-E horizontal length measuring machine; At permanent location (S) Internal procedure PA-M-17 based on EURAMET cg-6 v. 3.0
21 Setting standards for external dimensions Calibration — Length
25 mm to 100 mm · CMC 0,9 µm 100 mm to 200 mm · CMC 1,6 µm
Length
Internal procedure; Direct method using the ULM 520 S-E horizontal length measuring machine; At permanent location (S) Internal procedure PA-M-16
22 90° try squares Calibration — Angle
longer arm length from 40 mm to 100 mm · CMC 3 µm longer arm length from 100 mm to 200 mm · CMC 4 µm longer arm length from 200 mm to 300 mm · CMC 5 µm
Angle
Internal procedure; At permanent location (S) Internal procedure PA-M-12
23 Builder's spirit levels Calibration — Angle
(zero setting error) — length up to 100 cm · CMC 0,25 mm
Angle
Internal procedure; At permanent location (S) Internal procedure PA-M-13
24 Temperature indicators (meters), including temperature controllers (for use with thermocouples) Calibration — Electrical simulation of quantities
-200 °C to 1820 °C · CMC 0,8 °C
Electrical simulation of quantities
Internal procedure; Indirect electrical method; At permanent location (S) Internal procedure PA-T-06 based on EURAMET cg-11 v. 2.0 PN-EN 60584-1:2014-04
25 Temperature indicators (meters), including temperature controllers (for use with resistance sensors) Calibration — Electrical simulation of quantities
-200 °C to 850 °C · CMC 0,2 °C
Electrical simulation of quantities
Internal procedure; Indirect electrical method; At permanent location (S) Internal procedure PA-T-06 based on EURAMET cg-11 v. 2.0 PN-EN IEC 60751:2022-11
26 Torque wrenches
Torque screwdrivers
Calibration — Torque
2 N·m to 1000 N·m · CMC 0,9 % 1 N·m to 10 N·m · CMC 0,9 %
Torque
Internal procedure; At permanent location (S) and outside of it (P) Internal procedure PA-M-09 based on PN-EN ISO 6789-1:2017-03 PN-EN ISO 6789-2:2017-03
27 Hygrometers
Thermohygrometers
Calibration — Relative humidity
for temperatures in the range -10 °C to 0 °C — 50 %rh to 80 %rh · CMC 1,3 %rh (rh = 50 %); 2,0 %rh (rh = 80 %) for temperatures in the range 0 °C to 10 °C — 20 %rh to 50 %rh · CMC 1,4 %rh for temperatures in the range 0 °C to 10 °C — 50 %rh to 90 %rh · CMC 1,8 %rh for temperatures in the range 10 °C to 20 °C — 20 %rh to 50 %rh · CMC 1,1 %rh for temperatures in the range 10 °C to 20 °C — 50 %rh to 90 %rh · CMC 1,5 %rh for temperatures in the range 20 °C to 40 °C — 10 %rh to 50 %rh · CMC 1,0 %rh for temperatures in the range 20 °C to 40 °C — 50 %rh to 90 %rh · CMC 1,4 %rh for temperatures in the range 40 °C to 50 °C — 10 %rh to 50 %rh · CMC 1,0 %rh
Relative humidity
Internal procedure; At permanent location (S) Internal procedure PA-H-01
28 Bourdon tube pressure gauges (barometers)
Electronic pressure gauges (barometers)
Calibration — Pressure
- absolute pressure — 800 hPa to 1100 hPa · CMC 0,6 hPa
Pressure
Internal procedure; At permanent location (S) Internal procedure PA-C-01 based on EURAMET cg-17 v. 4.1
29 Bourdon tube pressure gauges
Electronic pressure gauges
Calibration — Pressure
- gauge pressure — -2500 Pa to 2500 Pa · CMC 1,3 Pa - gauge pressure — -0,1 MPa to 0,1 MPa · CMC 0,00008 MPa - gauge pressure — 0,1 MPa to 1 MPa · CMC 0,0004 MPa - gauge pressure — 1 MPa to 4 MPa · CMC 0,0015 MPa - gauge pressure — 4 MPa to 35 MPa · CMC 0,017 MPa
Pressure
Internal procedure; At permanent location (S) Internal procedure PA-C-01 based on EURAMET cg-17 v. 4.1
30 Bourdon tube pressure gauges (barometers)
Electronic pressure gauges (barometers)
Calibration — Pressure
- absolute pressure — 800 hPa to 1100 hPa · CMC 1,6 hPa
Pressure
Internal procedure; Outside of permanent location (P) Internal procedure PA-C-01 based on EURAMET cg-17 v. 4.1
31 Bourdon tube pressure gauges
Electronic pressure gauges
Calibration — Pressure
- gauge pressure — -2500 Pa to 2500 Pa · CMC 3,0 Pa - gauge pressure — -0,1 MPa to 0,1 MPa · CMC 0,0002 MPa - gauge pressure — 0,1 MPa to 1 MPa · CMC 0,0008 MPa - gauge pressure — 1 MPa to 4 MPa · CMC 0,003 MPa - gauge pressure — 4 MPa to 35 MPa · CMC 0,025 MPa
Pressure
Internal procedure; Outside of permanent location (P) Internal procedure PA-C-01 based on EURAMET cg-17 v. 4.1
32 Pressure transmitters Calibration — Pressure
- gauge pressure - for current output signal — -2500 Pa to 2500 Pa · CMC 1,5 Pa - gauge pressure - for voltage output signal — -2500 Pa to 2500 Pa · CMC 2,0 Pa - gauge pressure - for current output signal — 0 MPa to 1 Mpa · CMC 0,0005 Mpa - gauge pressure - for voltage output signal — 0 MPa to 1 Mpa · CMC 0,0007 Mpa
Pressure
Internal procedure; At permanent location (S) Internal procedure PA-C-02 based on EURAMET cg-17 v. 4.1
33 Electrical thermometers (including electronic)
Electrical thermometers (with temperature recording)
Calibration — Temperature (electrical thermometry)
-30 °C to 105 °C · CMC 0,06 °C 105 °C to 200 °C · CMC 0,06 °C 200 °C to 260 °C · CMC 0,3 °C
Temperature (electrical thermometry)
Internal procedure; At permanent location (S) Internal procedure PA-T-05
34 Electrical thermometers (including electronic)
Electrical thermometers (with temperature recording)
Calibration — Temperature (electrical thermometry)
-20 °C to 200 °C · CMC 0,2 °C
Temperature (electrical thermometry)
Internal procedure; Outside of permanent location (P) Internal procedure PA-T-05
35 Resistance thermometer sensors Calibration — Temperature (electrical thermometry)
-30 °C to 105 °C · CMC 0,08 °C 105 °C to 200 °C · CMC 0,16 °C 0 °C · CMC 0,05 °C
Temperature (electrical thermometry)
Internal procedure; At permanent location (S) Internal procedure PA-T-03
36 Climatic chambers
Thermostatic chambers
Calibration — Temperature (electrical thermometry)
-30 °C to 200 °C · CMC 0,3 °C 1)
Temperature (electrical thermometry)
Internal procedure; At permanent location (S) and outside of it (P) Internal procedure PA-T-08 based on EURAMET cg-20 v. 5.0
37 Steam sterilisation chambers (e.g. autoclaves) Calibration — Temperature (electrical thermometry)
0 °C to 140 °C · CMC 0,4 °C 1)
Temperature (electrical thermometry)
Internal procedure; At permanent location (S) and outside of it (P) Internal procedure PA-T-08
38 Liquid baths Calibration — Temperature (electrical thermometry)
-30 °C to 200 °C · CMC 0,3 °C 1)
Temperature (electrical thermometry)
Internal procedure; At permanent location (S) and outside of it (P) Internal procedure PA-T-09
39 Liquid-in-glass thermometers Calibration — Temperature (non-electrical thermometry)
- with a scale interval of not less than 0,1 °C — -30 °C to 105 °C · CMC 0,08 °C - with a scale interval of not less than 0,1 °C — 105 °C to 200 °C · CMC 0,10 °C
Temperature (non-electrical thermometry)
Internal procedure; At permanent location (S) Internal procedure PA-T-01
40 Bimetallic dial thermometers
Expansion dial thermometers
Pressure-spring dial thermometers
Calibration — Temperature (non-electrical thermometry)
0 °C to 200 °C · CMC 0,3 °C
Temperature (non-electrical thermometry)
Internal procedure; At permanent location (S) Internal procedure PA-T-07
41 Radiation pyrometers
Thermal imaging cameras
Calibration — Temperature (radiation thermometry)
-15 °C do 0 °C · CMC 1,9 °C 0 °C do 35 °C · CMC 1,7 °C 35 °C do 100 °C · CMC 2,1 °C 100 °C to 200 °C · CMC 2,6 °C 200 °C do 350 °C · CMC 3,3 °C 350 °C do 500 °C · CMC 4,2 °C
Temperature (radiation thermometry)
Internal procedure; At permanent location (S) Internal procedure PA-T-04
42 One-mark glass volumetric flasks Calibration — Volume
2000 ml · CMC 0,22 ml 1000 ml · CMC 0,12 ml 500 ml · CMC 0,083 ml 250 ml · CMC 0,054 ml 200 ml · CMC 0,054 ml 100 ml · CMC 0,025 ml 50 ml · CMC 0,015 ml 25 ml · CMC 0,010 ml 20 ml · CMC 0,010 ml 10 ml · CMC 0,006 ml
Volume
Internal procedure; At permanent location (S) Internal procedure PA-F-01 based on PN-EN ISO 4787:2022-06
43 One-mark pipettes Calibration — Volume
50 ml to 100 ml · CMC 0,025 ml 25 ml to 50 ml · CMC 0,013 ml 20 ml to 25 ml · CMC 0,008 ml 10 ml to 20 ml · CMC 0,008 ml 5 ml to 10 ml · CMC 0,005 ml 2 ml to 5 ml · CMC 0,004 ml 1 ml to 2 ml · CMC 0,003 ml 0,5 ml to 1 ml · CMC 0,0025 ml 0,5 ml · CMC 0,0015 ml
Volume
Internal procedure; At permanent location (S) Internal procedure PA-F-01 based on PN-EN ISO 4787:2022-06
44 Graduated pipettes Calibration — Volume
10 ml to 25 ml · CMC 0,03 ml 5 ml to 10 ml · CMC 0,014 ml 2 ml to 5 ml · CMC 0,008 ml 1 ml to 2 ml · CMC 0,003 ml 0,5 ml to 1 ml · CMC 0,002 ml 0,5 ml · CMC 0,0015 ml
Volume
Internal procedure; At permanent location (S) Internal procedure PA-F-01 based on PN-EN ISO 4787:2022-06
45 Burettes Calibration — Volume
100 ml · CMC 0,04 ml 50 ml · CMC 0,017 ml 25 ml · CMC 0,017 ml 10 ml · CMC 0,007 ml 5 ml · CMC 0,003 ml 2 ml · CMC 0,003 ml 1 ml · CMC 0,003 ml
Volume
Internal procedure; At permanent location (S) Internal procedure PA-F-01 based on PN-EN ISO 4787:2022-06
46 Graduated measuring cylinders Calibration — Volume
2000 ml · CMC 1,3 ml 1000 ml · CMC 0,80 ml 500 ml · CMC 0,50 ml 250 ml · CMC 0,29 ml 100 ml · CMC 0,13 ml 50 ml · CMC 0,13 ml 25 ml · CMC 0,07 ml 10 ml · CMC 0,03 ml
Volume
Internal procedure; At permanent location (S) Internal procedure PA-F-01 based on PN-EN ISO 4787:2022-06
47 Measuring tapes Calibration — Length
0 m to 25 m · CMC Q[0,23; 0,02 · L] mm
Length
Internal procedure; At permanent location (S) Internal procedure PA-M-07
48 Laser distance meters Calibration — Length
0 m to 5 m · CMC 1,0 mm 5 m do 25 m · CMC 1,2 mm
Length
Internal procedure; At permanent location (S) Internal procedure PA-M-14
49 Anemometers Calibration — Air velocity (flow – gases)
0,15 m/s to 1,2 m/s · CMC 0,07 m/s 1,2 m/s to 6,5 m/s · CMC 0,3 m/s
Air velocity (flow – gases)
Internal procedure; Orifice plate measurement; At permanent location (S) Internal procedure PA-V-01
50 Anemometers Calibration — Air velocity (flow – gases)
6,5 m/s to 15,0 m/s · CMC 0,3 m/s 15,0 m/s to 30,0 m/s · CMC 0,6 m/s 30,0 m/s to 40,0 m/s · CMC 0,9 m/s
Air velocity (flow – gases)
Internal procedure; Measurement with a static Pitot tube; At permanent location (S) Internal procedure PA-V-01

Reference standards (41)

EURAMET cg-11 v. 2.0
EURAMET cg-17 v. 4.1
EURAMET cg-20 v. 5.0
EURAMET cg-6 v. 3.0
OIML R126-2:2021 A.1.1, A.2
PA-C-01
PA-C-02
PA-F-01
PA-F-02
PA-H-01
PA-M-01
PA-M-02
PA-M-03
PA-M-04
PA-M-05
PA-M-06
PA-M-07
PA-M-08
PA-M-09
PA-M-10
PA-M-11
PA-M-12
PA-M-13
PA-M-14
PA-M-15
PA-M-16
PA-M-17
PA-T-01
PA-T-03
PA-T-04
PA-T-05
PA-T-06
PA-T-07
PA-T-08
PA-T-09
PA-V-01
PN-EN 60584-1:2014-04
PN-EN IEC 60751:2022-11
PN-EN ISO 4787:2022-06
PN-EN ISO 6789-1:2017-03
PN-EN ISO 6789-2:2017-03

The same scope as data (JSON): https://labcoda.pl/api/accreditation-scopes/labs/PL/AP%20106