🇵🇱 Metrotest Sp. z o.o. PL

PCA AP 005 • Elbląg, Poland • 147 calibration items

Metrology & calibration

Metrotest Sp. z o.o. is a calibration laboratory accredited by PCA under number AP 005 (Elbląg, Poland). Its accreditation scope covers 147 calibration items in the following areas: Metrology & calibration. Calibrated items include: Special gauges, Analogue inch dial indicators with a scale interval of:, Multimeters, Clamp meters. Most frequently used calibration principles: Internal procedure; At permanent location (S), Internal procedure; Angle measurement using the PRISMO measuring ma…, Internal procedure; Calibration using the PRISMO measuring machine;….

At a glance

  • Accreditation number: PCA AP 005
  • Calibration items in scope: 147
  • Types of calibrated items: 102
  • Calibration principles used: 23
  • City: Elbląg, Poland
  • Valid until: 30-12-2029
Accreditation number
AP 005
Accreditation body
PCA
Address
ul. Stoczniowa 2, 82-300 Elbląg
City
Elbląg, Poland
Division
Measurement Laboratory
Valid until
30-12-2029

What this laboratory calibrates (102)

Calibration principles (23)

Certificate information

Issue date
21.07.2025
Issue no.
28
Certificate date
22.08.2019
Accreditation cycle
04.12.2025 — 30.12.2029
Approved by
Katarzyna Wiśniewska

Accreditation scope — calibration items (147)

The uncertainty covered by the CMC is the expanded uncertainty with a coverage probability of approximately 95 % and is expressed in measurand units. The value of the uncertainty covered by the CMC expressed as a percentage is the relative measurement uncertainty and refers to the percentage share of the value of the measurand.

No. Calibrated quantity / subject of calibration Nominal range / parameters / CMC Calibration principle Calibration procedure
Calibration items
1 Analogue dial indicators with a scale interval of 0,001 mm Calibration — Length
0 mm to 5 mm · CMC 0,4 µm
Length
Internal procedure; At permanent location (S) MT/I-203
2 Analogue lever dial indicators with a scale interval of 0,001 mm Calibration — Length
0 mm to 5 mm · CMC 0,4 µm
Length
Internal procedure; At permanent location (S) MT/I-203
3 Analogue dial indicators with a scale interval of 0,002 mm Calibration — Length
0 mm to 5 mm · CMC 0,4 µm
Length
Internal procedure; At permanent location (S) MT/I-203
4 Analogue lever dial indicators with a scale interval of 0,002 mm Calibration — Length
0 mm to 3 mm · CMC 0,4 µm
Length
Internal procedure; At permanent location (S) MT/I-203
5 Analogue dial indicators
with a scale interval of 0,005 mm
Calibration — Length
0 mm to 5 mm · CMC 0,7 µm
Length
Internal procedure; At permanent location (S) MT/I-203
6 Analogue lever dial indicators with a scale interval of 0,005 mm Calibration — Length
0 mm to 3 mm · CMC 0,7 µm
Length
Internal procedure; At permanent location (S) MT/I-203
7 Analogue dial indicators with a scale interval of 0,01 mm Calibration — Length
0 mm do 1 mm · CMC 0,6 µm 0 mm do 3 mm · CMC 0,6 µm 0 mm do 5 mm · CMC 0,7 µm 0 mm do 10 mm · CMC 0,8 µm 0 mm do 30 mm · CMC 0,9 µm 0 mm to 50 mm · CMC 1,2 µm 0 mm do 80 mm · CMC 2,1 µm 0 mm do 100 mm · CMC 2,7 µm
Length
Internal procedure; At permanent location (S) MT/I-203
8 Analogue lever dial indicators with a scale interval of 0,01 mm Calibration — Length
0 mm to 1 mm · CMC 0,6 µm 0 mm to 3 mm · CMC 0,6 µm
Length
Internal procedure; At permanent location (S) MT/I-203
9 Analogue dial indicators with a scale interval of 0,02 mm Calibration — Length
0 mm do 1 mm · CMC 1,2 µm 0 mm do 3 mm · CMC 1,2 µm 0 mm do 5 mm · CMC 1,2 µm 0 mm do 10 mm · CMC 1,3 µm 0 mm do 30 mm · CMC 1,3 µm 0 mm to 50 mm · CMC 1,6 µm 0 mm do 80 mm · CMC 2,3 µm 0 mm do 100 mm · CMC 2,8 µm
Length
Internal procedure; At permanent location (S) MT/I-203
10 Analogue lever dial indicators with a scale interval of 0,02 mm Calibration — Length
0 mm to 1 mm · CMC 1,2 µm 0 mm to 3 mm · CMC 1,2 µm
Length
Internal procedure; At permanent location (S) MT/I-203
11 Analogue dial indicators with a scale interval of 0,1 mm Calibration — Length
0 mm do 10 mm · CMC 5,8 µm 0 mm to 50 mm · CMC 5,9 µm 0 mm do 100 mm · CMC 6,4 µm
Length
Internal procedure; At permanent location (S) MT/I-203
12 Analogue inch dial indicators with a scale interval of: Calibration — Length
0,00127 mm / 0,00005’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 0,4 µm / 0,00002’’ 0,00254 mm / 0,00010’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 0,4 µm / 0,00002’’ 0,00635 mm / 0,00025’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 0,8 µm / 0,00003’’ 0,0127 mm / 0,0005’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 0,8 µm / 0,00003’’ 0,0254 mm / 0,001’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 1,5 µm / 0,00006’’
Length
Internal procedure; At permanent location (S) MT/I-203
13 Analogue inch lever dial indicators with a scale interval of: Calibration — Length
0,00127 mm / 0,00005’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 0,4 µm / 0,00002’’ 0,00254 mm / 0,00010’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 0,4 µm / 0,00002’’ 0,00635 mm / 0,00025’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 0,8 µm / 0,00003’’ 0,0127 mm / 0,0005’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 0,8 µm / 0,00003’’ 0,0254 mm / 0,001’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 1,5 µm / 0,00006’’
Length
Internal procedure; At permanent location (S) MT/I-203
14 Analogue inch dial indicators with a scale interval of: Calibration — Length
0,00254 mm / 0,0001’’ — 0 mm to 25,4 mm / 0’’ to 1,0000’’ · CMC 0,7 µm / 0,00003’’ 0,0254 mm / 0,001’’ — 0 mm to 25,4 mm / 0’’ to 1,0000’’ · CMC 1,6 µm / 0,00006’’ 0,254 mm / 0,01’’ — 0 mm to 25,4 mm / 0’’ to 1,0000’’ · CMC 14,7 µm / 0,00058’’
Length
Internal procedure; At permanent location (S) MT/I-203
15 Analogue inch dial indicators with a scale interval of: Calibration — Length
0,0254 mm / 0,001’’ — 0 mm to 50,8 mm / 0’’ to 2,0000’’ · CMC 1,6 µm / 0,00006’’ 0,127 mm / 0,005’’ — 0 mm to 50,8 mm / 0’’ to 2,0000’’ · CMC 7,4 µm / 0,00029’’
Length
Internal procedure; At permanent location (S) MT/I-203
16 Analogue inch dial indicators with a scale interval of: Calibration — Length
0,0254 mm / 0,001’’ — 0 mm to 76,2 mm / 0’’ to 3,0000’’ · CMC 2,5 µm / 0,00010’’ 0,127 mm / 0,005’’ — 0 mm to 76,2 mm / 0’’ to 3,0000’’ · CMC 7,6 µm / 0,00030’’
Length
Internal procedure; At permanent location (S) MT/I-203
17 Digital indicators with a resolution of 0,0001 mm Calibration — Length
0 mm to 3 mm · CMC 0,3 µm
Length
Internal procedure; At permanent location (S) MT/I-203
18 Digital indicators with a resolution of 0,0002 mm Calibration — Length
0 mm to 3 mm · CMC 0,3 µm
Length
Internal procedure; At permanent location (S) MT/I-203
19 Digital indicators with a resolution of 0,0005 mm Calibration — Length
0 mm to 3 mm · CMC 0,4 µm
Length
Internal procedure; At permanent location (S) MT/I-203
20 Digital indicators with a resolution of 0,0005 mm Calibration — Length
0 mm do 12,7 mm · CMC 0,6 µm 0 mm do 25,4 mm · CMC 0,7 µm 0 mm to 50,8 mm · CMC 1,1 µm 0 mm do 100 mm · CMC 2,6 µm
Length
Internal procedure; At permanent location (S) MT/I-203
21 Digital indicators with a resolution of 0,001 mm Calibration — Length
0 mm do 12,7 mm · CMC 0,8 µm 0 mm do 25,4 mm · CMC 0,9 µm 0 mm to 50,8 mm · CMC 1,2 µm 0 mm do 100 mm · CMC 2,7 µm
Length
Internal procedure; At permanent location (S) MT/I-203
22 Digital indicators with a resolution of 0,002 mm Calibration — Length
0 mm do 12,7 mm · CMC 1,3 µm 0 mm do 25,4 mm · CMC 1,3 µm 0 mm to 50,8 mm · CMC 1,6 µm 0 mm do 100 mm · CMC 2,8 µm
Length
Internal procedure; At permanent location (S) MT/I-203
23 Digital indicators with a resolution of 0,005 mm Calibration — Length
0 mm do 12,7 mm · CMC 2,9 µm 0 mm do 25,4 mm · CMC 3,0 µm 0 mm to 50,8 mm · CMC 3,1 µm 0 mm do 100 mm · CMC 3,9 µm
Length
Internal procedure; At permanent location (S) MT/I-203
24 Digital indicators with a resolution of 0,01 mm Calibration — Length
0 mm do 12,7 mm · CMC 5,8 µm 0 mm do 25,4 mm · CMC 5,8 µm 0 mm to 50,8 mm · CMC 5,9 µm 0 mm do 100 mm · CMC 6,4 µm
Length
Internal procedure; At permanent location (S) MT/I-203
25 Digital indicators with a resolution of 0,02 mm Calibration — Length
0 mm do 12,7 mm · CMC 11,6 µm 0 mm do 25,4 mm · CMC 11,6 µm 0 mm to 50,8 mm · CMC 11,7 µm 0 mm do 100 mm · CMC 11,9 µm
Length
Internal procedure; At permanent location (S) MT/I-203
26 Digital lever indicators with a resolution of 0,001 mm Calibration — Length
0 mm to 3 mm · CMC 0,6 µm
Length
Internal procedure; At permanent location (S) MT/I-203
27 Digital lever indicators with a resolution of 0,01 mm Calibration — Length
0 mm to 3 mm · CMC 5,8 µm
Length
Internal procedure; At permanent location (S) MT/I-203
28 Special indicators Calibration — Length
0 mm to 1000 mm · CMC 4,9 µm
Length
Internal procedure; Calibration using a height gauge; At permanent location (S) MT/I-234
29 Reference foils Calibration — Length
0,002 mm to 25 mm · CMC 1,0 µm
Length
Internal procedure; At permanent location (S) MT/I-219
30 Dial depth gauges Calibration — Length
0 mm to 50 mm · CMC 0,7 µm 50 mm do 100 mm · CMC 0,9 µm 100 mm do 150 mm · CMC 1,2 µm 150 mm do 200 mm · CMC 1,5 µm
Length
Internal procedure; At permanent location (S) MT/I-203
31 Caliper depth gauges Calibration — Length
0 mm to 2000 mm · CMC (13 + 22 · L) µm
Length
Internal procedure; At permanent location (S) MT/I-202
32 Micrometer depth gauges Calibration — Length
0 mm to 25 mm · CMC 2,3 µm 0 mm to 50 mm · CMC 2,4 µm 0 mm do 75 mm · CMC 2,7 µm 0 mm do 100 mm · CMC 2,9 µm 0 mm do 150 mm · CMC 3,5 µm 0 mm to 200 mm · CMC 4,1 µm 0 mm do 300 mm · CMC 5,6 µm
Length
Internal procedure; At permanent location (S) MT/I-205
33 Micrometer heads Calibration — Length
0 mm to 50 mm · CMC 1,0 µm
Length
Internal procedure; At permanent location (S) MT/I-205
34 Dial thickness gauges Calibration — Length
0 mm to 500 mm · CMC 2,0 µm
Length
Internal procedure; At permanent location (S) MT/I-230
35 Ultrasonic thickness gauges: Calibration — Length
with a resolution of 0,01 mm — 0 mm to 500 mm · CMC 6,0 µm with a resolution of 0,001 mm — 0 mm to 50 mm · CMC 1,6 µm
Length
Internal procedure; At permanent location (S) MT/I-230
36 Measuring balls Calibration — Length
0,5 mm to 100 mm · CMC 1,0 µm
Length
Internal procedure; Length and diameter measurement using the ULM 600 horizontal length measuring machine; At permanent location (S) MT/I-223
37 Sine bars Calibration — Length
0 mm to 200 mm · CMC 2,5 µm 200 mm to 400 mm · CMC 5,1 µm
Length
Internal procedure; Calibration using the PRISMO measuring machine; At permanent location (S) MT/I-237
38 Dial calipers (internal/external) Calibration — Length
0 mm to 500 mm · CMC 2,0 µm
Length
Internal procedure; At permanent location (S) MT/I-230
39 Coating thickness gauges Calibration — Length
0 mm to 1 mm · CMC 1,0 µm
Length
Internal procedure; At permanent location (S) MT/I-230
40 Internal micrometers Calibration — Length
5 mm to 30 mm · CMC 1,2 µm 30 mm to 55 mm · CMC 1,5 µm
Length
Internal procedure; At permanent location (S) MT/I-205
41 External micrometers Calibration — Length
0 mm to 25 mm · CMC 1,2 µm 25 mm to 50 mm · CMC 1,2 µm 50 mm to 75 mm · CMC 1,3 µm 75 mm to 100 mm · CMC 1,4 µm 100 mm do 200 mm · CMC 1,8 µm 200 mm do 300 mm · CMC 2,3 µm 300 mm do 400 mm · CMC 3,0 µm 400 mm do 500 mm · CMC 3,7 µm 500 mm do 600 mm · CMC 4,5 µm 600 mm do 700 mm · CMC 5,6 µm 700 mm do 800 mm · CMC 6,0 µm 800 mm do 900 mm · CMC 6,9 µm 900 mm do 1000 mm · CMC 7,6 µm 1000 mm do 1100 mm · CMC 7,9 µm 1100 mm do 1200 mm · CMC 8,5 µm 1200 mm do 1300 mm · CMC 9,2 µm 1300 mm do 1400 mm · CMC 10,7 µm 1400 mm do 1500 mm · CMC 11,0 µm 1500 mm do 1600 mm · CMC 12,1 µm 1600 mm do 1700 mm · CMC 12,9 µm 1700 mm do 1800 mm · CMC 13,6 µm 1800 mm do 1900 mm · CMC 14,3 µm 1900 mm do 2000 mm · CMC 15,0 µm
Length
Internal procedure; At permanent location (S) MT/I-205
42 Setting rings Calibration — Length
1 mm to 10 mm · CMC 0,8 µm 10 mm to 290 mm · CMC 1,6 µm 1 mm to 800 mm* · CMC 2,7 µm*
Length
Internal procedure; - using the PRISMO coordinate measuring machine*; At permanent location (S) MT/I-210
43 Special plates Calibration — Length
0 mm to 200 mm · CMC 4,0 µm 200 mm do 600 mm · CMC 5,1 µm 600 mm do 1200 mm · CMC 8,1 µm
Length
Internal procedure; Length measurement using the PRISMO measuring machine; At permanent location (S) MT/I-224
44 V-blocks Calibration — Length
0 mm to 200 mm · CMC 3,6 µm 200 mm do 315 mm · CMC 5,1 µm
Length
Internal procedure; Length measurement using the PRISMO measuring machine; At permanent location (S) MT/I-224
45 Tape measures Calibration — Length
0 mm to 5000 mm · CMC (0,024 + 0,009 · L) mm 0 mm to 10000 mm · CMC (0,048 + 0,009 · L) mm 0 mm to 15000 mm · CMC (0,072 + 0,009 · L) mm 0 mm to 20000 mm · CMC (0,096 + 0,009 · L) mm 0 mm to 25000 mm · CMC (0,120 + 0,009 · L) mm 0 mm to 30000 mm · CMC (0,144 + 0,009 · L) mm
Length
Internal procedure; At permanent location (S) MT/I-204
46 Indicating snap gauges Calibration — Length
0 mm to 25 mm · CMC 1,2 µm 0 mm to 50 mm · CMC 1,2 µm 0 mm do 75 mm · CMC 1,3 µm 0 mm do 100 mm · CMC 1,3 µm 0 mm do 150 mm · CMC 1,5 µm 0 mm to 200 mm · CMC 1,8 µm 0 mm do 300 mm · CMC 2,3 µm
Length
Internal procedure; At permanent location (S) MT/I-205
47 Special caliper instruments:
Digital weld gauges
Analogue weld gauges
Calibration — Length
0 mm to 50 mm · CMC 14 µm
Length
Internal procedure; Measurement of welds on a plane; At permanent location (S) MT/I-202
48 Calipers Calibration — Length
0 mm to 2000 mm · CMC (13 + 22 · L) µm
Length
Internal procedure; At permanent location (S) MT/I-202
49 Cylindrical thread plug gauges Calibration — Length
1 mm to 100 mm · CMC 3,0 µm 100 mm to 300 mm · CMC 3,2 µm
Length
Internal procedure; At permanent location (S) MT/I-233
50 Cylindrical thread ring gauges Calibration — Length
5 mm to 100 mm · CMC 3,2 µm 100 mm to 200 mm · CMC 3,4 µm
Length
Internal procedure; At permanent location (S) MT/I-233
51 Slot gauges Calibration — Length
0,5 mm to 50 mm · CMC 3,6 µm
Length
Internal procedure; Length measurement using the PRISMO measuring machine; At permanent location (S) MT/I-224
52 Taper gauges Calibration — Length
0 mm to 500 mm · CMC 3,6 µm
Length
Internal procedure; Length and diameter measurement using the PRISMO measuring machine; At permanent location (S) MT/I-224
53 Special gauges Calibration — Length
1 mm to 100 mm · CMC 1,0 µm 100 mm to 600 mm · CMC 1,2 µm
Length
Internal procedure; Length measurement using the ULM 600 horizontal length measuring machine; At permanent location (S) MT/I-223
54 Special gauges Calibration — Length
0 mm to 1200 mm · CMC 1,6 µm
Length
Internal procedure; Length measurement using the PRISMO measuring machine; At permanent location (S) MT/I-224
55 Special gauges Calibration — Length
0 mm to 1000 mm · CMC 5,4 µm
Length
Internal procedure; Length measurement using a micrometer; At permanent location (S) MT/I-227
56 Special gauges Calibration — Length
0 mm to 1000 mm · CMC 29 µm
Length
Internal procedure; Length measurement using a caliper; At permanent location (S) MT/I-228
57 Special gauges Calibration — Length
0 mm to 200 mm · CMC 3,2 µm
Length
Internal procedure; Length measurement using a measuring microscope; At permanent location (S) MT/I-225
58 Special gauges Calibration — Length
0 mm to 1000 mm · CMC 4,9 µm
Length
Internal procedure; Length measurement using a height gauge; At permanent location (S) MT/I-226
59 Plug gauges Calibration — Length
1 mm to 30 mm · CMC 1,0 µm 30 mm to 50 mm · CMC 1,0 µm 50 mm to 80 mm · CMC 1,1 µm 80 mm to 100 mm · CMC 1,2 µm
Length
Internal procedure; At permanent location (S) MT/I-218
60 Feeler gauges Calibration — Length
0,01 mm to 2 mm · CMC 1,0 µm
Length
Internal procedure; At permanent location (S) MT/I-212
61 Taper feeler gauges Calibration — Length
0 mm to 200 mm · CMC 3,2 µm
Length
Internal procedure; Length measurement using a measuring microscope; At permanent location (S) MT/I-225
62 Dial bore gauges Calibration — Length
4 mm to 18 mm · CMC 0,7 µm 18 mm to 50 mm · CMC 1,0 µm 50 mm to 150 mm · CMC 1,7 µm 150 mm to 315 mm · CMC 3,2 µm 315 mm to 500 mm · CMC 4,9 µm
Length
Internal procedure; At permanent location (S) MT/I-203
63 Two-point internal micrometers Calibration — Length
0 mm to 100 mm · CMC 1 µm 100 mm to 200 mm · CMC 1 µm 200 mm to 300 mm · CMC 2 µm 300 mm to 400 mm · CMC 2 µm 400 mm to 500 mm · CMC 2 µm 500 mm to 600 mm · CMC 2 µm 600 mm to 700 mm · CMC 8 µm 700 mm to 800 mm · CMC 10 µm 800 mm to 900 mm · CMC 12 µm 900 mm to 1000 mm · CMC 14 µm 1000 mm to 1100 mm · CMC 15 µm 1100 mm to 1200 mm · CMC 16 µm 1200 mm to 1300 mm · CMC 17 µm 1300 mm to 1400 mm · CMC 18 µm 1400 mm to 1500 mm · CMC 19 µm 1500 mm to 1600 mm · CMC 20 µm 1600 mm to 1700 mm · CMC 21 µm 1700 mm to 1800 mm · CMC 22 µm 1800 mm to 1900 mm · CMC 22,5 µm 1900 mm to 2000 mm · CMC 23 µm 2000 mm to 2100 mm · CMC 24 µm 2100 mm to 2200 mm · CMC 25 µm 2200 mm to 2300 mm · CMC 26,5 µm 2300 mm to 2400 mm · CMC 27,5 µm 2400 mm to 2500 mm · CMC 29 µm 2500 mm to 2600 mm · CMC 30 µm 2600 mm to 2700 mm · CMC 32 µm 2700 mm to 2800 mm · CMC 34 µm 2800 mm to 2900 mm · CMC 37 µm 2900 mm to 3000 mm · CMC 38 µm
Length
Internal procedure; At permanent location (S) MT/I-205
64 Three-point internal micrometers Calibration — Length
2 mm to 100 mm · CMC 1,9 µm 100 mm to 200 mm · CMC 3,3 µm 200 mm to 300 mm · CMC 4,3 µm
Length
Internal procedure; At permanent location (S) MT/I-205
65 Measuring wires Calibration — Length
0,05 mm to 20 mm · CMC 1,0 µm
Length
Internal procedure; At permanent location (S) MT/I-232
66 Caliper height gauges Calibration — Length
0 mm to 2000 mm · CMC (13 + 22 · L) µm
Length
Internal procedure; At permanent location (S) MT/I-202
67 Digital height gauges Calibration — Length
0 mm do 350 mm · CMC 3,2 µm 0 mm to 600 mm · CMC 3,8 µm 0 mm do 900 mm · CMC 4,4 µm 0 mm do 1100 mm · CMC 4,8 µm
Length
Internal procedure; At permanent location (S) and outside of it (P) MT/I-202
68 Setting standards for external dimensions Calibration — Length
0 mm to 100 mm · CMC 1,0 µm 100 mm to 200 mm · CMC 1,1 µm 200 mm to 300 mm · CMC 1,2 µm 300 mm to 400 mm · CMC 1,4 µm 400 mm to 500 mm · CMC 1,6 µm 500 mm to 600 mm · CMC 1,8 µm 600 mm to 700 mm · CMC 8 µm 700 mm to 800 mm · CMC 10 µm 800 mm to 900 mm · CMC 11 µm 900 mm to 1000 mm · CMC 12 µm 1000 mm to 1100 mm · CMC 13 µm 1100 mm to 1200 mm · CMC 13,5 µm 1200 mm to 1300 mm · CMC 14 µm 1300 mm to 1400 mm · CMC 15 µm 1400 mm to 1500 mm · CMC 16 µm 1500 mm to 1600 mm · CMC 17 µm 1600 mm to 1700 mm · CMC 19 µm 1700 mm to 1800 mm · CMC 21 µm 1800 mm to 1900 mm · CMC 22 µm 1900 mm to 2000 mm · CMC 23 µm
Length
Internal procedure; At permanent location (S) MT/I-214
69 Length standards Calibration — Length
0 mm to 200 mm · CMC 2,5 µm 200 mm do 600 mm · CMC 5,1 µm 600 mm do 1200 mm · CMC 8,1 µm
Length
Internal procedure; Calibration using the PRISMO measuring machine; At permanent location (S) MT/I-238
70 Radius standards Calibration — Length
0 mm to 100 mm · CMC 2,5 µm
Length
Internal procedure; Calibration using the PRISMO measuring machine; At permanent location (S) MT/I-239
71 Thread profile standards Calibration — Length
0 mm to 100 mm · CMC 1,4 µm
Length
Internal procedure; Calibration using a measuring microscope; At permanent location (S) MT/I-236
72 Line standards Calibration — Length
0 mm to 200 mm · CMC 1,4 µm 100 mm do 200 mm · CMC 2,1 µm
Length
Internal procedure; Calibration using a measuring microscope; At permanent location (S) MT/I-235
73 Try squares
Cylindrical squares
Calibration — Angle
0 mm to 1000 mm · CMC 3,6 µm
Angle
Internal procedure; Calibration using the PRISMO coordinate measuring machine Determination of squareness deviation; At permanent location (S) MT/I-207
74 Universal bevel protractors Calibration — Angle
0° to 360° · CMC 1,5’
Angle
Internal procedure; At permanent location (S) MT/I-206
75 Special plates Calibration — Angle
0° to 180° · CMC 10”
Angle
Internal procedure; Angle measurement using the PRISMO measuring machine; At permanent location (S) MT/I-224
76 Measuring V-blocks Calibration — Angle
0° to 90° · CMC 10”
Angle
Internal procedure; Angle measurement using the PRISMO measuring machine; At permanent location (S) MT/I-224
77 Bar spirit levels Calibration — Angle
0 mm to 20 mm / 0,01 mm · CMC 0,002 mm/m 0 mm to 20 mm / 0,02 mm · CMC 0,003 mm/m 0 mm to 20 mm / 0,04 mm · CMC 0,006 mm/m 0 mm to 20 mm / 0,05 mm · CMC 0,007 mm/m 0 mm to 20 mm / 0,1 mm · CMC 0,014 mm/m 0 mm to 20 mm / 0,2 mm · CMC 0,029 mm/m 0 mm to 20 mm / 0,3 mm · CMC 0,043 mm/m
Angle
Internal procedure; At permanent location (S) MT/I-231
78 Special gauges Calibration — Angle
0° to 180° · CMC 10”
Angle
Internal procedure; Angle measurement using the PRISMO measuring machine; At permanent location (S) MT/I-225
79 Special gauges Calibration — Angle
0° to 360° · CMC 2,9’
Angle
Internal procedure; Angle measurement using a measuring microscope; At permanent location (S) MT/I-225
80 Taper gauges Calibration — Angle
0° to 120° · CMC 10”
Angle
Internal procedure; Angle measurement using the PRISMO measuring machine; At permanent location (S) MT/I-224
81 Angle standards Calibration — Angle
0° to 360° · CMC 10”
Angle
Internal procedure; Calibration using the PRISMO measuring machine; At permanent location (S) MT/I-224
82 Angle standards Calibration — Angle
0° to 360° · CMC 2,9’
Angle
Internal procedure; Calibration using a measuring microscope; At permanent location (S) MT/I-225
83 Thread profile standards Calibration — Angle
0° to 80° · CMC 2,9’
Angle
Internal procedure; Angle calibration using a measuring microscope; At permanent location (S) MT/I-225
84 Straight edges Calibration — Length (surface geometry)
50 mm to 100 mm · CMC 0,7 µm 10 mm to 1400 mm* · CMC 1,4 µm*
Length (surface geometry)
Internal procedure; - using the PRISMO coordinate measuring machine*; At permanent location (S) MT/I-211
85 Surface straight edges Calibration — Length (surface geometry)
10 mm to 1400 mm* · CMC 1,4 µm
Length (surface geometry)
Internal procedure; - using the PRISMO coordinate measuring machine*; At permanent location (S) MT/I-211
86 Surface plates Calibration — Length (surface geometry)
160x100 mm to 1000x630 mm · CMC 1,4 µm
Length (surface geometry)
Internal procedure; - using the PRISMO coordinate measuring machine; At permanent location (S) MT/I-229
87 Surface plates Calibration — Length (surface geometry)
250x250 mm to 2500x2000 mm · CMC 2,0 µm
Length (surface geometry)
Internal procedure; - using a spirit level / interferometer; At permanent location (S) and outside of it (P) MT/I-229
88 Measuring V-blocks Calibration — Length (surface geometry)
0 mm to 200 mm · CMC 3,6 µm 200 mm do 315 mm · CMC 5,1 µm
Length (surface geometry)
Internal procedure; Flatness deviation measurement using the PRISMO measuring machine; At permanent location (S) MT/I-224
89 Measuring tables Calibration — Length (surface geometry)
0 mm to 200 mm · CMC 3,6 µm 200 mm to 400 mm · CMC 5,1 µm
Length (surface geometry)
Internal procedure; Flatness deviation measurement using the PRISMO measuring machine; At permanent location (S) MT/I-224
90 Special gauges Calibration — Length (surface geometry)
0 mm to 200 mm · CMC 3,6 µm 200 mm do 600 mm · CMC 5,1 µm 600 mm do 1200 mm · CMC 8,1 µm
Length (surface geometry)
Internal procedure; Flatness deviation measurement using the PRISMO measuring machine; At permanent location (S) MT/I-224
91 Force gauges Calibration — Force
0,1 N to 500 N · CMC 0,12 % 500 N to 400 kN · CMC 0,47 % 400 kN to 1000 kN · CMC 0,70 %
Force
Internal procedure; At permanent location (S) MT/I-125
92 Force gauges Calibration — Force
0,1 N to 500 N · CMC 0,12 % 500 N to 400 kN · CMC 0,47 %
Force
Internal procedure; Outside of permanent location (P) MT/I-125
93 Torque wrenches
Torque screwdrivers
Calibration — Torque
0,2 Nm to 1000 Nm · CMC 0,4 % 1000 Nm to 3000 Nm · CMC 0,7 %
Torque
Internal procedure; At permanent location (S) MT/I-124 based on PN-EN ISO 6789-1:2017 PN-EN ISO 6789-2:2017
94 Torque wrenches
Torque screwdrivers
Calibration — Torque
0,2 Nm to 1000 Nm · CMC 0,4 %
Torque
Internal procedure; Outside of permanent location (P) MT/I-124 based on PN-EN ISO 6789-1:2017 PN-EN ISO 6789-2:2017
95 Torque transducers Calibration — Torque
0,2 Nm to 1,0 Nm · CMC 0,4 % 1 Nm to 1000 Nm · CMC 0,3 % 1000 Nm to 4000 Nm · CMC 0,6 %
Torque
Internal procedure; At permanent location (S) MT/I-128 based on BS 7882:2008
96 Torque transducers Calibration — Torque
0,2 Nm to 1,0 Nm · CMC 0,4 % 1 Nm to 1000 Nm · CMC 0,3 %
Torque
Internal procedure; Outside of permanent location (P) MT/I-128 based on BS 7882:2008
97 Analogue dial indicators with a scale interval of 0,001 mm Calibration — Length
0 mm to 5 mm · CMC 0,3 µm
Length
Internal procedure; At permanent location (S) MT/I-203
98 Analogue dial indicators with a scale interval of 0,002 mm Calibration — Length
0 mm to 5 mm · CMC 0,3 µm
Length
Internal procedure; At permanent location (S) MT/I-203
99 Analogue dial indicators with a scale interval of 0,005 mm Calibration — Length
0 mm to 5 mm · CMC 0,6 µm
Length
Internal procedure; At permanent location (S) MT/I-203
100 Analogue dial indicators with a scale interval of 0,01 mm Calibration — Length
0 mm do 1 mm · CMC 0,6 µm 0 mm do 3 mm · CMC 0,6 µm 0 mm do 5 mm · CMC 0,6 µm 0 mm do 10 mm · CMC 0,6 µm 0 mm do 30 mm · CMC 0,6 µm 0 mm to 50 mm · CMC 0,6 µm 0 mm do 80 mm · CMC 0,7 µm 0 mm do 100 mm · CMC 0,8 µm
Length
Internal procedure; At permanent location (S) MT/I-203
101 Analogue dial indicators with a scale interval of 0,02 mm Calibration — Length
0 mm do 1 mm · CMC 1,2 µm 0 mm do 3 mm · CMC 1,2 µm 0 mm do 5 mm · CMC 1,2 µm 0 mm do 10 mm · CMC 1,2 µm 0 mm do 30 mm · CMC 1,2 µm 0 mm to 50 mm · CMC 1,2 µm 0 mm do 80 mm · CMC 1,2 µm 0 mm do 100 mm · CMC 1,3 µm
Length
Internal procedure; At permanent location (S) MT/I-203
102 Analogue dial indicators with a scale interval of 0,1 mm Calibration — Length
0 mm do 10 mm · CMC 5,8 µm 0 mm to 50 mm · CMC 5,8 µm 0 mm do 100 mm · CMC 5,8 µm
Length
Internal procedure; At permanent location (S) MT/I-203
103 Analogue inch dial indicators with a scale interval of: Calibration — Length
0,00127 mm / 0,00005’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 0,4 µm / 0,00002’’ 0,00254 mm / 0,00010’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 0,4 µm / 0,00002’’ 0,00635 mm / 0,00025’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 0,7 µm / 0,00003’’ 0,0127 mm / 0,0005’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 0,7 µm / 0,00003’’ 0,0254 mm / 0,001’’ — 0 mm to 6,35 mm / 0’’ to 0,250’’ · CMC 1,5 µm / 0,00006’’
Length
Internal procedure; At permanent location (S) MT/I-203
104 Analogue inch dial indicators with a scale interval of: Calibration — Length
0,00254 mm / 0,0001’’ — 0 mm to 25,4 mm / 0’’ to 1,0000’’ · CMC 0,4 µm / 0,00002’’ 0,0254 mm / 0,001’’ — 0 mm to 25,4 mm / 0’’ to 1,0000’’ · CMC 1,5 µm / 0,00006’’ 0,254 mm / 0,01’’ — 0 mm to 25,4 mm / 0’’ to 1,0000’’ · CMC 14,7 µm / 0,00058’’
Length
Internal procedure; At permanent location (S) MT/I-203
105 Analogue inch dial indicators with a scale interval of: Calibration — Length
0,0254 mm / 0,001’’ — 0 mm to 50,8 mm / 0’’ to 2,0000’’ · CMC 1,5 µm / 0,00006’’ 0,127 mm / 0,005’’ — 0 mm to 50,8 mm / 0’’ to 2,0000’’ · CMC 7,4 µm / 0,00029’’
Length
Internal procedure; At permanent location (S) MT/I-203
106 Analogue inch dial indicators with a scale interval of: Calibration — Length
0,0254 mm / 0,001’’ — 0 mm to 76,2 mm / 0’’ to 3,0000’’ · CMC 1,5 µm / 0,00006’’ 0,127 mm / 0,005’’ — 0 mm to 76,2 mm / 0’’ to 3,0000’’ · CMC 7,4 µm / 0,00029’’
Length
Internal procedure; At permanent location (S) MT/I-203
107 Digital indicators with a resolution of 0,0001 mm Calibration — Length
0 mm to 3 mm · CMC 0,1 µm
Length
Internal procedure; At permanent location (S) MT/I-203
108 Digital indicators with a resolution of 0,0002 mm Calibration — Length
0 mm to 3 mm · CMC 0,1 µm
Length
Internal procedure; At permanent location (S) MT/I-203
109 Digital indicators with a resolution of 0,0005 mm Calibration — Length
0 mm to 3 mm · CMC 0,3 µm
Length
Internal procedure; At permanent location (S) MT/I-203
110 Digital indicators with a resolution of 0,0005 mm Calibration — Length
0 mm do 12,7 mm · CMC 0,3 µm 0 mm do 25,4 mm · CMC 0,3 µm 0 mm to 50,8 mm · CMC 0,4 µm 0 mm do 100 mm · CMC 0,6 µm
Length
Internal procedure; At permanent location (S) MT/I-203
111 Digital indicators with a resolution of 0,001 mm Calibration — Length
0 mm do 12,7 mm · CMC 0,6 µm 0 mm do 25,4 mm · CMC 0,6 µm 0 mm to 50,8 mm · CMC 0,6 µm 0 mm do 100 mm · CMC 0,8 µm
Length
Internal procedure; At permanent location (S) MT/I-203
112 Digital indicators with a resolution of 0,002 mm Calibration — Length
0 mm do 12,7 mm · CMC 1,2 µm 0 mm do 25,4 mm · CMC 1,2 µm 0 mm to 50,8 mm · CMC 1,2 µm 0 mm do 100 mm · CMC 1,3 µm
Length
Internal procedure; At permanent location (S) MT/I-203
113 Digital indicators with a resolution of 0,005 mm Calibration — Length
0 mm do 12,7 mm · CMC 2,9 µm 0 mm do 25,4 mm · CMC 2,9 µm 0 mm to 50,8 mm · CMC 2,9 µm 0 mm do 100 mm · CMC 2,9 µm
Length
Internal procedure; At permanent location (S) MT/I-203
114 Digital indicators with a resolution of 0,01 mm Calibration — Length
0 mm do 12,7 mm · CMC 5,8 µm 0 mm do 25,4 mm · CMC 5,8 µm 0 mm to 50,8 mm · CMC 5,8 µm 0 mm do 100 mm · CMC 5,8 µm
Length
Internal procedure; At permanent location (S) MT/I-203
115 Digital indicators with a resolution of 0,02 mm Calibration — Length
0 mm do 12,7 mm · CMC 11,6 µm 0 mm do 25,4 mm · CMC 11,6 µm 0 mm to 50,8 mm · CMC 11,6 µm 0 mm do 100 mm · CMC 11,6 µm
Length
Internal procedure; At permanent location (S) MT/I-203
116 Dial depth gauges Calibration — Length
0 mm to 50 mm · CMC 0,7 µm 50 mm do 100 mm · CMC 0,9 µm 100 mm do 150 mm · CMC 1,2 µm 150 mm do 200 mm · CMC 1,5 µm
Length
Internal procedure; At permanent location (S) MT/I-203
117 Caliper depth gauges Calibration — Length
0 mm to 630 mm · CMC (13 + 22 · L) µm
Length
Internal procedure; At permanent location (S) MT/I-202
118 Dial thickness gauges
Dial calipers (internal/external)
Calibration — Length
0 mm to 50 mm · CMC 2,0 µm
Length
Internal procedure; At permanent location (S) MT/I-230
119 External micrometers Calibration — Length
0 mm to 25 mm · CMC 1,2 µm 25 mm to 50 mm · CMC 1,2 µm 50 mm to 75 mm · CMC 1,3 µm 75 mm to 100 mm · CMC 1,4 µm 100 mm do 200 mm · CMC 1,8 µm 200 mm do 300 mm · CMC 2,3 µm
Length
Internal procedure; At permanent location (S) MT/I-205
120 Internal micrometers Calibration — Length
5 mm to 30 mm · CMC 1,2 µm 30 mm to 55 mm · CMC 1,5 µm
Length
Internal procedure; At permanent location (S) MT/I-205
121 Gauge blocks cl. 0, 1, 2 Calibration — Length
0,5 mm to 100 mm · CMC (0,042 + 0,42 · L) µm
Length
Internal procedure; At permanent location (S) MT/I-201
122 Gauge blocks cl. 1, 2 Calibration — Length
125 mm to 500 mm · CMC (0,089 + 0,29 · L) µm
Length
Internal procedure; At permanent location (S) MT/I-217
123 Rigid rules Calibration — Length
0 mm do 300 mm · CMC (0,048 + 0,0014 · L) mm 0 mm do 500 mm · CMC (0,052 + 0,0014 · L) mm 0 mm to 1000 mm · CMC (0,061 + 0,0015 · L) mm 0 mm do 1500 mm · CMC (0,071 + 0,0015 · L) mm 0 mm do 2000 mm · CMC (0,081 + 0,0016 · L) mm 0 mm do 3000 mm · CMC (0,101 + 0,0016 · L) mm
Length
Internal procedure; At permanent location (S) MT/I-204
124 Semi-rigid rules Calibration — Length
0 mm do 100 mm · CMC (0,044 + 0,0013 · L) mm 0 mm do 150 mm · CMC (0,045 + 0,0013 · L) mm 0 mm to 200 mm · CMC (0,046 + 0,0013 · L) mm 0 mm do 300 mm · CMC (0,048 + 0,0014 · L) mm 0 mm do 500 mm · CMC (0,052 + 0,0014 · L) mm 0 mm to 1000 mm · CMC (0,061 + 0,0015 · L) mm 0 mm do 1500 mm · CMC (0,071 + 0,0015 · L) mm 0 mm do 2000 mm · CMC (0,081 + 0,0016 · L) mm 0 mm do 2500 mm · CMC (0,091 + 0,0016 · L) mm 0 mm do 3000 mm · CMC (0,101 + 0,0016 · L) mm
Length
Internal procedure; At permanent location (S) MT/I-204
125 Tape measures Calibration — Length
0 mm to 1000 mm · CMC (0,061 + 0,0015 · L) mm 0 mm do 2000 mm · CMC (0,081 + 0,0016 · L) mm 0 mm do 3000 mm · CMC (0,101 + 0,0016 · L) mm
Length
Internal procedure; At permanent location (S) MT/I-204
126 Special caliper instruments:
Digital weld gauges
Analogue weld gauges
Calibration — Length
0 mm to 50 mm · CMC 14 µm
Length
Internal procedure; Measurement of welds on a plane; At permanent location (S) MT/I-202
127 Cylindrical thread plug gauges Calibration — Length
1 mm to 100 mm · CMC 3,0 µm 100 mm to 300 mm · CMC 3,2 µm
Length
Internal procedure; At permanent location (S) MT/I-233
128 Plug gauges Calibration — Length
1 mm to 50 mm · CMC 0,5 µm 50 mm to 100 mm · CMC 0,9 µm
Length
Internal procedure; At permanent location (S) MT/I-218
129 Calipers Calibration — Length
0 mm to 630 mm · CMC (13 + 22 · L) µm
Length
Internal procedure; At permanent location (S) MT/I-202
130 Dial bore gauges Calibration — Length
4 mm to 18 mm · CMC 0,7 µm 18 mm to 50 mm · CMC 1,0 µm 50 mm to 150 mm · CMC 1,7 µm 150 mm to 315 mm · CMC 3,2 µm 315 mm to 500 mm · CMC 4,9 µm
Length
Internal procedure; At permanent location (S) MT/I-203
131 Two-point internal micrometers Calibration — Length
0 mm to 100 mm · CMC 1 µm 100 mm to 200 mm · CMC 1 µm 200 mm to 300 mm · CMC 2 µm 300 mm to 400 mm · CMC 2 µm 400 mm to 500 mm · CMC 2 µm 500 mm to 600 mm · CMC 2 µm 600 mm to 700 mm · CMC 8 µm 700 mm to 800 mm · CMC 10 µm 800 mm to 900 mm · CMC 12 µm 900 mm to 1000 mm · CMC 14 µm 1000 mm to 1100 mm · CMC 15 µm 1100 mm to 1200 mm · CMC 16 µm 1200 mm to 1300 mm · CMC 17 µm 1300 mm to 1400 mm · CMC 18 µm 1400 mm to 1500 mm · CMC 19 µm 1500 mm to 1600 mm · CMC 20 µm 1600 mm to 1700 mm · CMC 21 µm 1700 mm to 1800 mm · CMC 22 µm 1800 mm to 1900 mm · CMC 22,5 µm 1900 mm to 2000 mm · CMC 23 µm
Length
Internal procedure; At permanent location (S) MT/I-205
132 Measuring wires Calibration — Length
0,05 mm to 20 mm · CMC 1,0 µm
Length
Internal procedure; At permanent location (S) MT/I-232
133 Caliper height gauges Calibration — Length
0 mm to 630 mm · CMC (13 + 22 · L) µm
Length
Internal procedure; At permanent location (S) MT/I-202
134 Setting standards for external dimensions Calibration — Length
0 mm to 100 mm · CMC 1,0 µm 100 mm to 200 mm · CMC 1,1 µm 200 mm to 300 mm · CMC 1,2 µm 300 mm to 400 mm · CMC 1,4 µm 400 mm to 500 mm · CMC 1,6 µm 500 mm to 600 mm · CMC 1,8 µm 600 mm to 700 mm · CMC 8 µm 700 mm to 800 mm · CMC 10 µm 800 mm to 900 mm · CMC 11 µm 900 mm to 1000 mm · CMC 12 µm 1000 mm to 1100 mm · CMC 13 µm 1100 mm to 1200 mm · CMC 13,5 µm 1200 mm to 1300 mm · CMC 14 µm 1300 mm to 1400 mm · CMC 15 µm 1400 mm to 1500 mm · CMC 16 µm 1500 mm to 1600 mm · CMC 17 µm 1600 mm to 1700 mm · CMC 19 µm 1700 mm to 1800 mm · CMC 21 µm 1800 mm to 1900 mm · CMC 22 µm 1900 mm to 2000 mm · CMC 23 µm
Length
Internal procedure; At permanent location (S) MT/I-214
135 Multimeters
Analogue voltmeters
Digital voltmeters
Calibration — DC voltage
0 µV to 200 mV · CMC 2,2 · 10⁻⁵ · U + 2,1 µV 200 mV to 2 V · CMC 1,2 · 10⁻⁵ · U + 2,0 µV 2 V to 20 V · CMC 1,2 · 10⁻⁵ · U + 3,4 µV 20 V to 200 V · CMC 2,6 · 10⁻⁵ · U + 0,46 mV 200 V to 1000 V · CMC 2,5 · 10⁻⁵ · U + 0,50 mV
DC voltage
Internal procedure; At permanent location (S) MT/I-252 based on Euramet cg-15 v. 3.0 02/2015
136 Multimeters
Analogue ammeters
Digital ammeters
Clamp meters
Calibration — DC current
0 µA to 200 µA · CMC 4,0 · 10⁻⁴ · I + 5,8 nA 200 µA to 2 mA · CMC 4,0 · 10⁻⁴ · I + 46 nA 2 mA to 20 mA · CMC 4,0 · 10⁻⁴ · I + 0,46 µA 20 mA to 200 mA · CMC 4,3 · 10⁻⁴ · I + 4,6 µA 200 mA to 2 A · CMC 1,5 · 10⁻⁴ · I + 35 µA 2 A to 10 A · CMC 3,5 · 10⁻⁴ · I + 0,35 mA 10 A to 20 A · CMC 3,4 · 10⁻⁴ · I + 0,41 mA
DC current
Internal procedure; At permanent location (S) MT/I-252 based on Euramet cg-15 v. 3.0 02/2015
137 Clamp meters Calibration — DC current
20 A to 100 A · CMC 9,2 · 10⁻³ · I + 29 mA 100 A to 1000 A · CMC 5,7 · 10⁻³ · I + 0,62 A
DC current
Internal procedure; At permanent location (S) MT/I-252 based on Euramet cg-15 v. 3.0 02/2015
138 Multimeters
Analogue voltmeters
Digital voltmeters
Calibration — AC voltage
f = 10 Hz to 44 Hz — 0,2 mV to 200 mV · CMC 9,2 · 10⁻⁴ · U + 17 µV f = 10 Hz to 44 Hz — 200 mV to 2 V · CMC 5,8 · 10⁻⁴ · U + 0,21 mV f = 10 Hz to 44 Hz — 2 V to 20 V · CMC 5,8 · 10⁻⁴ · U + 1,8 mV f = 10 Hz to 44 Hz — 20 V to 200 V · CMC 5,8 · 10⁻⁴ · U + 23 mV f = 10 Hz to 44 Hz — 200 V to 1000 V · CMC 6,4 · 10⁻⁴ · U + 0,23 V f = 44 Hz to 1 kHz — 0,2 mV to 200 mV · CMC 1,8 · 10⁻⁴ · U + 17 µV f = 44 Hz to 1 kHz — 200 mV to 2 V · CMC 1,8 · 10⁻⁴ · U + 0,14 mV f = 44 Hz to 1 kHz — 2 V to 20 V · CMC 1,8 · 10⁻⁴ · U + 1,2 mV f = 44 Hz to 1 kHz — 20 V to 200 V · CMC 1,7 · 10⁻⁴ · U + 14 mV f = 44 Hz to 1 kHz — 200 V to 1000 V · CMC 2,3 · 10⁻⁴ · U + 69 mV f = 1 kHz to 20 kHz — 0,2 mV to 200 mV · CMC 2,3 · 10⁻⁴ · U + 32 µV f = 1 kHz to 20 kHz — 200 mV to 2 V · CMC 2,4 · 10⁻⁴ · U + 0,21 mV f = 1 kHz to 20 kHz — 2 V to 20 V · CMC 2,4 · 10⁻⁴ · U + 1,8 mV f = 1 kHz to 20 kHz — 20 V to 200 V · CMC 2,3 · 10⁻⁴ · U + 18 mV f = 1 kHz to 10 kHz — 200 V to 1000 V · CMC 2,9 · 10⁻⁴ · U + 0,14 V
AC voltage
Internal procedure; At permanent location (S) MT/I-252 based on Euramet cg-15 v. 3.0 02/2015
139 Multimeters
Analogue ammeters
Digital ammeters
Clamp meters
Calibration — AC current
f = 10 Hz to 44 Hz — 10 µA to 2 mA · CMC 2,3 · 10⁻³ · I + 0,29 µA f = 10 Hz to 44 Hz — 2 mA to 20 mA · CMC 2,3 · 10⁻³ · I + 3,5 µA f = 10 Hz to 44 Hz — 20 mA to 200 mA · CMC 2,3 · 10⁻³ · I + 35 µA f = 10 Hz to 44 Hz — 200 mA to 2 A · CMC 2,3 · 10⁻³ · I + 0,35 mA f = 10 Hz to 44 Hz — 2 A to 10 A · CMC 2,3 · 10⁻³ · I + 3,5 mA f = 10 Hz to 44 Hz — 10 A to 20 A · CMC 2,3 · 10⁻³ · I + 3,5 mA f = 44 Hz to 1 kHz — 10 µA to 200 µA · CMC 8,1 · 10⁻⁴ · I + 0,17 µA f = 44 Hz to 1 kHz — 200 µA to 2 mA · CMC 6,9 · 10⁻⁴ · I + 0,23 µA f = 44 Hz to 1 kHz — 2 mA to 20 mA · CMC 4,6 · 10⁻⁴ · I + 2,3 µA f = 44 Hz to 1 kHz — 20 mA to 200 mA · CMC 4,6 · 10⁻⁴ · I + 23 µA f = 44 Hz to 1 kHz — 200 mA to 2 A · CMC 6,9 · 10⁻⁴ · I + 0,23 mA f = 44 Hz to 1 kHz — 2 A to 10 A · CMC 9,2 · 10⁻⁴ · I + 2,3 mA f = 44 Hz to 1 kHz — 10 A to 20 A · CMC 9,2 · 10⁻⁴ · I + 2,3 mA f = 1 kHz to 10 kHz — 10 µA to 200 µA · CMC 9,2 · 10⁻³ · I + 0,29 µA f = 1 kHz to 10 kHz — 200 µA to 2 mA · CMC 5,8 · 10⁻³ · I + 0,35 µA f = 1 kHz to 10 kHz — 2 mA to 20 mA · CMC 2,9 · 10⁻³ · I + 3,5 µA f = 1 kHz to 10 kHz — 20 mA to 200 mA · CMC 5,8 · 10⁻³ · I + 46 µA f = 1 kHz to 5 kHz — 200 mA to 2 A · CMC 5,8 · 10⁻³ · I + 0,46 mA f = 0,1 kHz to 1 kHz — 2 A to 10 A · CMC 3,5 · 10⁻³ · I + 4,6 mA f = 0,1 kHz to 1 kHz — 10 A to 20 A · CMC 3,5 · 10⁻³ · I + 4,6 mA
AC current
Internal procedure; At permanent location (S) MT/I-252 based on Euramet cg-15 v. 3.0 02/2015
140 Clamp meters Calibration — AC current
f = 30 Hz to 60 Hz — 20 A to 100 A · CMC 9,2 · 10⁻³ · I + 29 mA f = 30 Hz to 60 Hz — 100 A to 1000 A · CMC 5,7 ⋅ 10⁻³ · I + 0,62 A
AC current
Internal procedure; At permanent location (S) MT/I-252 based on Euramet cg-15 v. 3.0 02/2015
141 Multimeters
Digital ohmmeters
Calibration — DC resistance
0,01 Ω to 10 Ω · CMC 1,8 ⋅ 10⁻⁵ · R + 0,15 mΩ 10 Ω to 20 Ω · CMC 1,9 ⋅ 10⁻⁵ · R + 0,15 mΩ 20 Ω to 100 Ω · CMC 2,0 ⋅ 10⁻⁵ · R + 0,93 mΩ 100 Ω to 200 Ω · CMC 2,0 ⋅ 10⁻⁵ · R + 0,89 mΩ 0,2 kΩ to 2 kΩ · CMC 1,1 ⋅ 10⁻⁵ · R + 0,90 mΩ 2 kΩ to 20 kΩ · CMC 1,1 ⋅ 10⁻⁵ · R + 9,0 mΩ 20 kΩ to 200 kΩ · CMC 4,1 ⋅ 10⁻⁵ · R + 0,21 Ω 0,2 MΩ to 2 MΩ · CMC 7,5 ⋅ 10⁻⁵ · R + 1,2 Ω 2 MΩ to 20 MΩ · CMC 2,9 ⋅ 10⁻⁴ · R + 14 Ω 20 MΩ to 100 MΩ · CMC 6,4 ⋅ 10⁻⁴ · R + 690 Ω
DC resistance
Internal procedure; At permanent location (S) MT/I-252 based on Euramet cg-15 v. 3.0 02/2015
142 Temperature indicators (meters), including temperature controllers
Temperature recorders
Temperature simulators
Calibration — Electrical simulation of quantities
-200 °C to 850 °C · CMC 0,02 °C
Electrical simulation of quantities
Internal procedure; At permanent location (S) and outside of it (P) MT/I-250 MT/I-260 based on Euramet cg-11 v. 2.0 03/2011 PN-EN IEC 60751:2022-11
143 Temperature indicators (meters), including temperature controllers
Temperature recorders
Temperature simulators
Calibration — Electrical simulation of quantities
-200 °C to 1800 °C · CMC 0,6 °C
Electrical simulation of quantities
Internal procedure; At permanent location (S) and outside of it (P) MT/I-250 MT/I-260 based on Euramet cg-11 v. 2.0 03/2011 PN-EN 60584-1:2014-04
144 Bourdon tube pressure gauges
- gauge pressure: positive pressure (oil)
Calibration — Pressure
0,02 MPa do 0,06 MPa · CMC 340 Pa 0,06 MPa do 0,6 MPa · CMC 0,0016 MPa 0,6 MPa to 6 MPa · CMC 0,012 MPa 6 MPa do 60 MPa · CMC 0,34 MPa
Pressure
Internal procedure; At permanent location (S) MT/I-261 based on Euramet cg-17 v. 4.1 methods cl. 5.2.1 and 5.2.2
145 Bourdon tube pressure gauges
- gauge pressure: positive pressure
(distilled water)
Calibration — Pressure
0,1 MPa to 6 MPa · CMC 0,042 MPa 6 MPa to 60 MPa · CMC 0,12 MPa
Pressure
Internal procedure; At permanent location (S) MT/I-261 based on Euramet cg-17 v. 4.1 methods cl. 5.2.1 and 5.2.2
146 Noble metal thermocouples type S
Base metal thermocouples types K and J
Calibration — Temperature (electrical thermometry)
80 °C to 1050 °C · CMC 1,3 °C
Temperature (electrical thermometry)
Internal procedure; At permanent location (S) MT/I-251 based on Euramet cg-8 v. 3.1 02/2020
147 Electrical thermometers (including electronic) Calibration — Temperature (electrical thermometry)
-80 °C to 100 °C · CMC 0,05 °C
Temperature (electrical thermometry)
Internal procedure; At permanent location (S) MT/I-255

Reference standards (49)

BS 7882:2008
Euramet cg-11 v. 2.0 03/2011
Euramet cg-15 v. 3.0 02/2015
Euramet cg-17 v. 4.1 metody pkt 5.2.1 i 5.2.2
Euramet cg-8 v. 3.1 02/2020
MT/I-124
MT/I-125
MT/I-128
MT/I-201
MT/I-202
MT/I-203
MT/I-204
MT/I-205
MT/I-206
MT/I-207
MT/I-210
MT/I-211
MT/I-212
MT/I-214
MT/I-217
MT/I-218
MT/I-219
MT/I-223
MT/I-224
MT/I-225
MT/I-226
MT/I-227
MT/I-228
MT/I-229
MT/I-230
MT/I-231
MT/I-232
MT/I-233
MT/I-234
MT/I-235
MT/I-236
MT/I-237
MT/I-238
MT/I-239
MT/I-250
MT/I-251
MT/I-252
MT/I-255
MT/I-260
MT/I-261
PN-EN 60584-1:2014-04
PN-EN IEC 60751:2022-11
PN-EN ISO 6789-1:2017
PN-EN ISO 6789-2:2017

The same scope as data (JSON): https://labcoda.pl/api/accreditation-scopes/labs/PL/AP%20005