🇨🇿 EHSQ CONSULTING, s.r.o. PL
Metrology & calibration
EHSQ CONSULTING, s.r.o. is a calibration laboratory accredited by ČIA under number 2364 (Blatec, Czech Republic). Its accreditation scope covers 50 calibration items in the following areas: Metrology & calibration. Calibrated items include: Acceleration of linear harmonic mechanical vibrations / vibration c…, Dial indicators, Internal gauges, Length gauges, profile projectors, microscopes, devices with a line…. Most frequently used calibration principles: Measurement on a length gauge, Measurement by parallel gauge blocks, Measurement on a standard calibration device.
At a glance
- Accreditation number: ČIA 2364
- Calibration items in scope: 50
- Types of calibrated items: 40
- Calibration principles used: 33
- City: Blatec, Czech Republic
- Valid until: 27-11-2029
- Accreditation number
- 2364
- Accreditation body
- ČIA
- Address
- Blatec 48, 783 75 Blatec
- City
- Blatec, Czech Republic
- Division
- Laboratorium wzorcujące
- Valid until
- 27-11-2029
What this laboratory calibrates (40)
- Acceleration of linear harmonic mechanical vibrations / vibration calibrators, vibrometers, vibration systems — 2 calibration items
- Dial indicators — 2 calibration items
- Internal gauges — 2 calibration items
- Length gauges, profile projectors, microscopes, devices with a linear measuring system — 2 calibration items
- Levels — 2 calibration items
- Rpm meters — 2 calibration items
- Surface rules - straightness — 2 calibration items
- Thickness gauges — 2 calibration items
- Thread gauges, radius gauges, gauges, measuring jigs and templates — 2 calibration items
- Torque sensors and calibration devices — 2 calibration items
- Clinometers — 1 calibration item
- Cylindrical and slot gauges, measuring cylinders and setting gauges — 1 calibration item
- Feeler gauges — 1 calibration item
- Flat, trying and knife angles - perpendicularity deviation — 1 calibration item
- Frequency of mechanical linear motion — 1 calibration item
- and 25 more
Calibration principles (33)
- Measurement on a length gauge — 8 calibration items
- Measurement by parallel gauge blocks — 5 calibration items
- Measurement on a standard calibration device — 3 calibration items
- Comparison with a standard torque sensor — 2 calibration items
- Measurement on a profile projector — 2 calibration items
- Measurement or comparison on a standard calibration device — 2 calibration items
- Measurement with an electronic level — 2 calibration items
- By simulated electrical signal — 1 calibration item
- Comparison with a reference digital stopwatch — 1 calibration item
- Comparison with a rigid steel gauge — 1 calibration item
- Comparison with a rotation angle sensor — 1 calibration item
- Comparison with parallel gauge blocks on a comparator — 1 calibration item
- Comparison with reference torque wrenches — 1 calibration item
- Contact method — 1 calibration item
- Contactless method — 1 calibration item
- and 18 more
Certificate information
- Certificate date
- 27.11.2024
Accreditation scope — calibration items (50)
| No. | Calibrated quantity / subject of calibration | Nominal range / parameters / CMC | Calibration principle | Calibration procedure | |
|---|---|---|---|---|---|
| Calibration items | |||||
| 1 | Setting and check rings | Calibration – length 3 mm to 6 mm · CMC (9·L + 3,0) µm 6 mm to 300 mm · CMC (10·L + 0,8) µm CMC for the field of measured quantity: Length |
Measurement on a length gauge | KPD01KN | |
| 2 | Parallel gauge blocks | Calibration – length 0,5 mm to 100 mm · CMC (5·L + 0,2) µm CMC for the field of measured quantity: Length |
Comparison with parallel gauge blocks on a comparator | KPD02MK | |
| 3 | Cylindrical and slot gauges, measuring cylinders and setting gauges | Calibration – length 0 mm to 600 mm · CMC (9·L + 0,7) µm CMC for the field of measured quantity: Length |
Measurement on a length gauge | KPD03KV | |
| 4 | Snap gauges | Calibration – length 3 mm to 6 mm · CMC (10·L + 3,0) µm 6 mm to 300 mm · CMC (15·L + 0,8) µm CMC for the field of measured quantity: Length |
Measurement on a length gauge or a profile projector | KPD04KT | |
| 5 | Feeler gauges | Calibration – length 0 mm to 10 mm · CMC 0,7 µm CMC for the field of measured quantity: Length |
Measurement on a length gauge | KPD05SL | |
| 6 | Thread gauges | Calibration – length male gauge — 0 mm to 300 mm · CMC (10·L + 2,6) µm ring — 3 mm to 300 mm · CMC (10·L + 3,1) µm CMC for the field of measured quantity: Length |
Measurement on a length gauge | KPD06KZ | |
| 7 | Thread-measuring wires | Calibration – length 0,17 mm to 6,35 mm · CMC 0,5 µm CMC for the field of measured quantity: Length |
Measurement on a length gauge | KPD07DZ | |
| 8 | Slide gauges | Calibration – length 0 mm to 2000 mm · CMC (20·L + 20) µm CMC for the field of measured quantity: Length |
Measurement by parallel gauge blocks | KPD11MP | |
| 9 | Micrometers | Calibration – length 0 mm to 1000 mm · CMC (14·L + 1,3) µm CMC for the field of measured quantity: Length |
Measurement by parallel gauge blocks | KPD12MT | |
| 10 | Dial indicators | Calibration – length direct, lever — 0 mm to 100 mm · CMC (16·L + 0,8) µm CMC for the field of measured quantity: Length |
Measurement on a length gauge | KPD13UC | |
| 11 | Dial indicators | Calibration – length with arms — 0 mm to 200 mm · CMC (17·L + 3,0) µm CMC for the field of measured quantity: Length |
Measurement by setting rings and parallel gauge blocks | KPD13UC | |
| 12 | Mechanical sliding depth gauges | Calibration – length 0 mm to 600 mm · CMC (15·L + 12) µm CMC for the field of measured quantity: Length |
Measurement by parallel gauge blocks | KPD14HP | |
| 13 | Mechanical height gauges | Calibration – length 0 mm to 1000 mm · CMC (15·L + 1,4) µm CMC for the field of measured quantity: Length |
Measurement by parallel gauge blocks | KPD15VP | |
| 14 | Inside micrometer gauges | Calibration – length 0 mm to 1000 mm · CMC (15·L + 1,4) µm CMC for the field of measured quantity: Length |
Measurement on a length gauge | KPD16OM | |
| 15 | Internal gauges | Calibration – length two-contact — 0 mm to 600 mm · CMC (15·L + 1,4) µm CMC for the field of measured quantity: Length |
Measurement on a length gauge | KPD17DT | |
| 16 | Internal gauges | Calibration – length three-contact — 3 mm to 200 mm · CMC (17·L + 2,0) µm CMC for the field of measured quantity: Length |
Measurement by setting rings | KPD17DT | |
| 17 | Pasameters | Calibration – length 0 mm to 300 mm · CMC (8·L + 0,8) µm CMC for the field of measured quantity: Length |
Measurement by parallel gauge blocks | KPD18PM | |
| 18 | Steel gauges – rigid, thin, flexible, tape | Calibration – length 0 mm to 5000 mm · CMC 0,15 mm CMC for the field of measured quantity: Length |
Comparison with a rigid steel gauge | KPD09OM | |
| 19 | Surface rules - straightness | Calibration – length up to 1,000 mm in length — 0 mm to 5 mm · CMC 7 µm CMC for the field of measured quantity: Length |
Using parallel gauge blocks on a surface plate | KPD19PP | |
| 20 | Surface rules - straightness | Calibration – length up to 2,000 mm in length — 0 mm to 5 mm · CMC (1,2·L + 5,2) µm CMC for the field of measured quantity: Length |
Measurement with an electronic level | KPD19PP | |
| 21 | Surface plates - flatness | Calibration – length up to the length of the longer edge 3,000 mm — 0 mm to 5 mm · CMC (1,2·M + 5,2) µm CMC for the field of measured quantity: Length |
Measurement with an electronic level | KPD20PD | |
| 22 | Thickness gauges | Calibration – length surface layers — 0 mm to 2 mm · CMC 9,0 µm CMC for the field of measured quantity: Length |
Measurement using sheets | KPD21SV | |
| 23 | Thickness gauges | Calibration – length of wall thickness — 0 mm to 200 mm · CMC (14·L + 12) µm CMC for the field of measured quantity: Length |
Using reference gauges | KPD21SV | |
| 24 | Thread gauges, radius gauges, gauges, measuring jigs and templates | Calibration – length 0 mm to 200 mm · CMC (20·L + 4,0) µm CMC for the field of measured quantity: Length |
Measurement on a profile projector | KPU34MP | |
| 25 | Flat, trying and knife angles - perpendicularity deviation | Calibration – length up to the length of the longer arm 630 mm — 0 mm to 630 mm · CMC (15·H + 6,0) µm CMC for the field of measured quantity: Length |
Measurement of deviation from perpendicularity with a height gauge and dial gauge | KPU31UL | |
| 26 | Length gauges, profile projectors, microscopes, devices with a linear measuring system | Calibration – length 0 mm to 3000 mm · CMC (2·L + 0,2) µm CMC for the field of measured quantity: Length |
Measurement by a laser interferometer | KPD10LI | |
| 27 | Length gauges, profile projectors, microscopes, devices with a linear measuring system | Calibration – length 0 mm to 300 mm · CMC (12·L + 2,0) µm CMC for the field of measured quantity: Length |
Measurement with a reference gauge | KPD10LI | |
| 28 | Roughness meters | Calibration – length 0,1 µm to 6,4 µm · CMC (8 % + 0,20) µm CMC for the field of measured quantity: Length |
Measurement by a roughness standard | KPD22DR | |
| 29 | Roughness standards | Calibration – length 0,1 µm to 6,4 µm · CMC (8 % + 0,20) µm CMC for the field of measured quantity: Length |
Measurement by a roughness meter | KPD22DR | |
| 30 | Plane angle meters | Calibration – plane angle 0° to 360° · CMC 2´ CMC for the field of measured quantity: Plane angle |
Using angle gauges and sine ruler | KPU32MU | |
| 31 | Clinometers | Calibration – plane angle -180° to 180° · CMC 2´ CMC for the field of measured quantity: Plane angle |
Sine ruler measurement | KPU32MU | |
| 32 | Levels | Calibration – plane angle Mechanical — 0 mm/m to 2 mm/m · CMC (3,5·α + 5,2) µm/m CMC for the field of measured quantity: Plane angle |
Using an electronic level | KPU33LV | |
| 33 | Levels | Calibration – plane angle Builder’s — 0 mm/m to 2 mm/m · CMC 0,2 mm/m Electronic — -14 mm/m to 14 mm/m · CMC (3,5·α + 5,2) µm/m CMC for the field of measured quantity: Plane angle |
Small angle generator measurement | KPU33LV | |
| 34 | Thread gauges, radius gauges, gauges, measuring jigs and templates | Calibration – plane angle 0° to 360° · CMC 4´ CMC for the field of measured quantity: Plane angle |
Measurement on a profile projector | KPU34MP | |
| 35 | Rotary angle sensors and torque tools | Calibration – plane angle 0° to 360° · CMC 0,2° CMC for the field of measured quantity: Plane angle |
Comparison with a rotation angle sensor | KPU32MU | |
| 36 | Acceleration of linear harmonic mechanical vibrations / vibration calibrators, vibrometers, vibration systems | Calibration – mechanical motion 3 Hz to 10 kHz — 0,1 m·s⁻² to 500 m·s⁻² · CMC 2 % 10 Hz to 1 kHz — 0,1 m·s⁻² to 500 m·s⁻² · CMC 1 % 1 kHz to 5 kHz — 0,1 m·s⁻² to 500 m·s⁻² · CMC 1,5 % 5 kHz to 10 kHz — 0,1 m·s⁻² to 500 m·s⁻² · CMC 2,5 % CMC for the field of measured quantity: Mechanical motion |
Measurement or comparison on a standard calibration device | KPV01VZ | |
| 37 | Acceleration of linear harmonic mechanical vibrations / vibration calibrators, vibrometers, vibration systems | Calibration – mechanical motion 3 Hz to 10 kHz — 1 mV to 7 V · CMC 1 % CMC for the field of measured quantity: Mechanical motion |
By simulated electrical signal | KPV01VZ | |
| 38 | Frequency of mechanical linear motion | Calibration – mechanical motion 0.1 to 500 m·s⁻² — 3 Hz to 10 kHz · CMC 1 % CMC for the field of measured quantity: Mechanical motion |
Measurement or comparison on a standard calibration device | KPV01VZ | |
| 39 | Sensitivity of vibration sensors by vibration – sine signal | Calibration – mechanical motion acceleration, 0.1 m·s⁻² to 500 m·s⁻²; 3 Hz to 10 Hz — 0,01 pC / m·s⁻² to 1000 pC / m·s⁻² · CMC 2 % acceleration, 0.1 m·s⁻² to 500 m·s⁻²; 10 Hz to 1 kHz — 0,01 pC / m·s⁻² to 1000 pC / m·s⁻² · CMC 1 % acceleration, 0.1 m·s⁻² to 500 m·s⁻²; 1 kHz to 5 kHz — 0,01 pC / m·s⁻² to 1000 pC / m·s⁻² · CMC 1,5 % acceleration, 0.1 m·s⁻² to 500 m·s⁻²; 5 kHz to 10 kHz — 0,01 pC / m·s⁻² to 1000 pC / m·s⁻² · CMC 2,5 % acceleration, 0.1 m·s⁻² to 500 m·s⁻²; 3 Hz to 10 Hz — 0,01 mV / m·s⁻² to 10000 mV / m·s⁻² · CMC 2 % acceleration, 0.1 m·s⁻² to 500 m·s⁻²; 10 Hz to 1 kHz — 0,01 mV / m·s⁻² to 10000 mV / m·s⁻² · CMC 1 % acceleration, 0.1 m·s⁻² to 500 m·s⁻²; 1 kHz to 5 kHz — 0,01 mV / m·s⁻² to 10000 mV / m·s⁻² · CMC 1,5 % acceleration, 0.1 m·s⁻² to 500 m·s⁻²; 5 kHz to 10 kHz — 0,01 mV / m·s⁻² to 10000 mV / m·s⁻² · CMC 2,5 % acceleration, 0.1 m·s⁻² to 500 m·s⁻²; 3 Hz to 10 Hz — 1 mA / m·s⁻² to 100 mA / m·s⁻² · CMC 2 % acceleration, 0.1 m·s⁻² to 500 m·s⁻²; 10 Hz to 1 kHz — 1 mA / m·s⁻² to 100 mA / m·s⁻² · CMC 1 % acceleration, 0.1 m·s⁻² to 500 m·s⁻²; 1 kHz to 5 kHz — 1 mA / m·s⁻² to 100 mA / m·s⁻² · CMC 1,5 % acceleration, 0.1 m·s⁻² to 500 m·s⁻²; 5 kHz to 10 kHz — 1 mA / m·s⁻² to 100 mA / m·s⁻² · CMC 2,5 % velocity up to 0.4 m·s⁻¹; 3 Hz to 10 Hz — 0,01 pC / m·s⁻¹ to 1000 pC / m·s⁻¹ · CMC 2 % velocity up to 0.4 m·s⁻¹; 10 Hz to 1 kHz — 0,01 pC / m·s⁻¹ to 1000 pC / m·s⁻¹ · CMC 1 % velocity up to 0.4 m·s⁻¹; 1 kHz to 5 kHz — 0,01 pC / m·s⁻¹ to 1000 pC / m·s⁻¹ · CMC 1,5 % velocity up to 0.4 m·s⁻¹; 5 kHz to 10 kHz — 0,01 pC / m·s⁻¹ to 1000 pC / m·s⁻¹ · CMC 2,5 % velocity up to 0.4 m·s⁻¹; 3 Hz to 10 Hz — 0,01 mV / m·s⁻¹ to 10000 mV / m·s⁻¹ · CMC 2 % velocity up to 0.4 m·s⁻¹; 10 Hz to 1 kHz — 0,01 mV / m·s⁻¹ to 10000 mV / m·s⁻¹ · CMC 1 % velocity up to 0.4 m·s⁻¹; 1 kHz to 5 kHz — 0,01 mV / m·s⁻¹ to 10000 mV / m·s⁻¹ · CMC 1,5 % velocity up to 0.4 m·s⁻¹; 5 kHz to 10 kHz — 0,01 mV / m·s⁻¹ to 10000 mV / m·s⁻¹ · CMC 2,5 % velocity up to 0.4 m·s⁻¹; 3 Hz to 10 Hz — 1 mA / m·s⁻¹ to 100 mA / m·s⁻¹ · CMC 2 % velocity up to 0.4 m·s⁻¹; 10 Hz to 1 kHz — 1 mA / m·s⁻¹ to 100 mA / m·s⁻¹ · CMC 1 % velocity up to 0.4 m·s⁻¹; 1 kHz to 5 kHz — 1 mA / m·s⁻¹ to 100 mA / m·s⁻¹ · CMC 1,5 % velocity up to 0.4 m·s⁻¹; 5 kHz to 10 kHz — 1 mA / m·s⁻¹ to 100 mA / m·s⁻¹ · CMC 2,5 % deviation up to 5mm; 3 Hz to 10 Hz — 0,01 pC / mm to 1000 pC / mm · CMC 2 % deviation up to 5mm; 10 Hz to 1 kHz — 0,01 pC / mm to 1000 pC / mm · CMC 1 % deviation up to 5mm; 1 kHz to 5 kHz — 0,01 pC / mm to 1000 pC / mm · CMC 1,5 % deviation up to 5mm; 5 kHz to 10 kHz — 0,01 pC / mm to 1000 pC / mm · CMC 2,5 % deviation up to 5mm; 3 Hz to 10 Hz — 0,01 mV / mm to 10000 mV / mm · CMC 2 % deviation up to 5mm; 10 Hz to 1 kHz — 0,01 mV / mm to 10000 mV / mm · CMC 1 % deviation up to 5mm; 1 kHz to 5 kHz — 0,01 mV / mm to 10000 mV / mm · CMC 1,5 % deviation up to 5mm; 5 kHz to 10 kHz — 0,01 mV / mm to 10000 mV / mm · CMC 2,5 % deviation up to 5mm; 3 Hz to 10 Hz — 1 mA / mm to 100 mA / mm · CMC 2 % deviation up to 5mm; 10 Hz to 1 kHz — 1 mA / mm to 100 mA / mm · CMC 1 % deviation up to 5mm; 1 kHz to 5 kHz — 1 mA / mm to 100 mA / mm · CMC 1,5 % deviation up to 5mm; 5 kHz to 10 kHz — 1 mA / mm to 100 mA / mm · CMC 2,5 % CMC for the field of measured quantity: Mechanical motion |
Measurement on a standard calibration device | KPV01VZ | |
| 40 | Sensitivity of vibration sensors | Calibration – mechanical motion angular acceleration up to 5,300 °·s⁻²; 1 Hz to 5 kHz — 0,01 mV / °·s⁻² to 10000 mV / °·s⁻² · CMC 1,5 % angular velocity up to 2.5·10⁶ °·s⁻¹; 1 Hz to 5 kHz — 0,01 mV / °·s⁻¹ to 10000 mV / °·s⁻¹ · CMC 1,5 % angular deviation up to 30 °; 1 Hz to 5 kHz — 0,01 mV / ° to 10000 mV / ° · CMC 1,5 % CMC for the field of measured quantity: Mechanical motion |
Measurement on a standard calibration device | KPV01VZ | |
| 41 | Sensitivity of vibration sensors by mechanical shock – half-sine signal | Calibration – mechanical motion 50 m·s⁻² to 200 m·s⁻² — 0,01 pC / m·s⁻² to 1000 pC / m·s⁻² · CMC 2 % 200 m·s⁻² to 2·10³ m·s⁻² — 0,01 pC / m·s⁻² to 1000 pC / m·s⁻² · CMC 1,5 % 2·10³ m·s⁻² to 4·10⁴ m·s⁻² — 0,01 pC / m·s⁻² to 1000 pC / m·s⁻² · CMC 1,8 % 4·10⁴ m·s⁻² to 1·10⁵ m·s⁻² — 0,01 pC / m·s⁻² to 1000 pC / m·s⁻² · CMC 3 % 50 m·s⁻² to 200 m·s⁻² — 0,01 mV / m·s⁻² to 10000 mV / m·s⁻² · CMC 2 % 200 m·s⁻² to 2·10³ m·s⁻² — 0,01 mV / m·s⁻² to 10000 mV / m·s⁻² · CMC 1,5 % 2·10³ m·s⁻² to 4·10⁴ m·s⁻² — 0,01 mV / m·s⁻² to 10000 mV / m·s⁻² · CMC 1,8 % 4·10⁴ m·s⁻² to 1·10⁵ m·s⁻² — 0,01 mV / m·s⁻² to 10000 mV / m·s⁻² · CMC 3 % CMC for the field of measured quantity: Mechanical motion |
Measurement on a standard calibration device | KPV01VZ | |
| 42 | Rpm meters | Calibration – mechanical motion 6 min⁻¹ to 8000 min⁻¹ · CMC (0,2 + 2d) CMC for the field of measured quantity: Mechanical motion |
Contact method | KPV01VZ | |
| 43 | Rpm meters | Calibration – mechanical motion 6 s⁻¹ to 10⁵ s⁻¹ · CMC (0,012 % + 2d) CMC for the field of measured quantity: Mechanical motion |
Contactless method | KPV01VZ | |
| 44 | Torque wrenches and screwdrivers | Calibration – force – moment of force 0,02 Nm to 1000 Nm · CMC 0,7 % CMC for the field of measured quantity: Force – moment of force |
Comparison with a standard torque sensor | KPM41KM (ČSN EN ISO 6789-2) | |
| 45 | Torque sensors and calibration devices | Calibration – force – moment of force 0,01 Nm to 100 Nm · CMC 0,2 % CMC for the field of measured quantity: Force – moment of force |
Measurement by torque arms and weights | KPM42SM | |
| 46 | Torque sensors and calibration devices | Calibration – force – moment of force 20 Nm to 1000 Nm · CMC 0,2 % CMC for the field of measured quantity: Force – moment of force |
Comparison with reference torque wrenches | KPM42SM | |
| 47 | Tighteners and tightening devices | Calibration – force – moment of force 0,02 Nm to 500 Nm · CMC 1,2 % CMC for the field of measured quantity: Force – moment of force |
Comparison with a standard torque sensor | KPM43UM | |
| 48 | Load cells, dynamometres | Calibration – force – moment of force tension, compression — 0 N to 200 N · CMC 0,1 % + 1 mN CMC for the field of measured quantity: Force – moment of force |
Measurement by standard weights | KPS01SL (ČSN EN ISO 376) | |
| 49 | Testing devices, presses, load cells | Calibration – force – moment of force tension, compression — 0 N to 10 kN · CMC 0,2 % + 0,01 N CMC for the field of measured quantity: Force – moment of force |
Measurement by standard dynamometer | KPS01SL (ČSN EN ISO 376, ČSN EN ISO 7500-1) | |
| 50 | Time meters, stopwatches, timers | Calibration – time 1 s to 36000 s · CMC 0,2 s CMC for the field of measured quantity: Time |
Comparison with a reference digital stopwatch | KPC51SC | |
Reference standards (34)
KPC51SC
KPD01KN
KPD02MK
KPD03KV
KPD04KT
KPD05SL
KPD06KZ
KPD07DZ
KPD09OM
KPD10LI
KPD11MP
KPD12MT
KPD13UC
KPD14HP
KPD15VP
KPD16OM
KPD17DT
KPD18PM
KPD19PP
KPD20PD
KPD21SV
KPD22DR
KPM41KM
KPM42SM
KPM43UM
KPS01SL
KPU31UL
KPU32MU
KPU33LV
KPU34MP
KPV01VZ
ČSN EN ISO 376
ČSN EN ISO 6789-2
ČSN EN ISO 7500-1