🇨🇿 Kontrolní a měrová služba v.o.s. PL

ČIA 2300 • Jihlava, Czech Republic • 19 calibration items

Metrology & calibration

Kontrolní a měrová služba v.o.s. is a calibration laboratory accredited by ČIA under number 2300 (Jihlava, Czech Republic). Its accreditation scope covers 19 calibration items in the following areas: Metrology & calibration. Calibrated items include: Gauge blocks, Analogue protractors, special gauges and angle templates, Bore gauges, Check squares. Most frequently used calibration principles: Direct measurement on a CMM, Direct measurement of a standard (gauge blocks), Direct measurement on a length measuring machine.

At a glance

Accreditation number: ČIA 2300
Calibration items in scope: 19
Types of calibrated items: 18
Calibration principles used: 9
City: Jihlava, Czech Republic
Valid until: 13-05-2029

Accreditation number: 2300
Accreditation body: ČIA
Address: U Cihelny 2347/2, 586 01 Jihlava
City: Jihlava, Czech Republic
Division: Laboratorium wzorcujące KMS
Valid until: 13-05-2029

What this laboratory calibrates (18)

Gauge blocks — 2 calibration items
Analogue protractors, special gauges and angle templates — 1 calibration item
Bore gauges — 1 calibration item
Check squares — 1 calibration item
Cylindrical gauges, snap gauges, inside rod gauges — 1 calibration item
Dial bore gauges — 1 calibration item
Dial indicators — 1 calibration item
Digital protractors — 1 calibration item
Flat, thin and flexible rules, roll-up tape measures and tapes — 1 calibration item
Gauges and length measuring instruments, roundness and cylindricity gauges, straightness and flatness gauges, special fixtures and templates — 1 calibration item
Limit ring gauges — 1 calibration item
Micrometer callipers — 1 calibration item
Micrometer heads — 1 calibration item
Pasameters and micropasameters — 1 calibration item
Slide gauges, height gauges, depth gauges — 1 calibration item
and 3 more

Calibration principles (9)

Direct measurement on a CMM — 4 calibration items
Direct measurement of a standard (gauge blocks) — 3 calibration items
Direct measurement on a length measuring machine — 3 calibration items
Comparison with a standard (gauge blocks) — 2 calibration items
Direct measurement on a dial indicator calibrator, direct measurement on a length measuring machine — 2 calibration items
Indirect measurement on a length measuring machine — 2 calibration items
Calibration with a standard torque device — 1 calibration item
Direct measurement of a standard (setting rings) — 1 calibration item
Direct measurement on a dial indicator calibrator — 1 calibration item

Certificate information

Certificate date: 30.08.2024

Accreditation scope — calibration items (19)

CMC — lowest stated expanded measurement uncertainty (ILAC-P14, EA-4/02 M); if not stated otherwise, coverage probability approx. 95 % and values without a unit are relative to the measured value. The uncertainty of a specific calibration may be higher.

No.	Calibrated quantity / subject of calibration	Nominal range / parameters / CMC	Calibration principle	Calibration procedure
Calibration items
1	Slide gauges, height gauges, depth gauges	Calibration – length 0 mm to 2000 mm · CMC 20 µm CMC for the field of measured quantity: Length	Direct measurement of a standard (gauge blocks)	KP 001
2	Micrometer callipers	Calibration – length 0 mm to 500 mm · CMC (2·L + 2) µm CMC for the field of measured quantity: Length	Direct measurement of a standard (gauge blocks)	KP 002
3	Dial indicators	Calibration – length 0 mm to 100 mm · CMC (11·L + 0,7) µm CMC for the field of measured quantity: Length	Direct measurement on a dial indicator calibrator, direct measurement on a length measuring machine	KP 003
4	Micrometer heads	Calibration – length 0 mm to 100 mm · CMC (8·L + 1,5) µm CMC for the field of measured quantity: Length	Direct measurement on a dial indicator calibrator, direct measurement on a length measuring machine	KP 003
5	Gauge blocks	Calibration – length 0,5 mm to 100 mm · CMC (2,5·L + 0,25) µm CMC for the field of measured quantity: Length	Comparison with a standard (gauge blocks)	KP 004
6	Gauge blocks	Calibration – length 100 mm to 1000 mm · CMC (2,1·L + 0,5) µm CMC for the field of measured quantity: Length	Comparison with a standard (gauge blocks)	KP 015
7	Dial bore gauges	Calibration – length 10 mm to 160 mm · CMC 1,1 µm CMC for the field of measured quantity: Length	Direct measurement on a dial indicator calibrator	KP 005
8	Cylindrical gauges, snap gauges, inside rod gauges	Calibration – length 0,1 mm to 1000 mm · CMC (3,7·L + 0,7) µm CMC for the field of measured quantity: Length	Direct measurement on a length measuring machine	KP 006
9	Limit ring gauges	Calibration – length 1 mm to 275 mm · CMC (3·L + 0,9) µm CMC for the field of measured quantity: Length	Direct measurement on a length measuring machine	KP 007
10	Thread plug gauges	Calibration – length thread pitch diameter — 1 mm to 200 mm · CMC (3·L + 2,6) µm CMC for the field of measured quantity: Length	Indirect measurement on a length measuring machine	KP 008
11	Pasameters and micropasameters	Calibration – length 0 mm to 200 mm · CMC (3·L + 0,5) µm CMC for the field of measured quantity: Length	Direct measurement of a standard (gauge blocks)	KP 009
12	Flat, thin and flexible rules, roll-up tape measures and tapes	Calibration – length 0 mm to 50 m · CMC (0,12·L + 0,12) mm CMC for the field of measured quantity: Length	Direct measurement on a length measuring machine	KP 012
13	Bore gauges	Calibration – length 3 mm to 275 mm · CMC 2 µm CMC for the field of measured quantity: Length	Direct measurement of a standard (setting rings)	KP 013
14	Thread ring gauge	Calibration – length thread pitch diameter — 3 mm to 180 mm · CMC (2·L + 3,2) µm CMC for the field of measured quantity: Length	Indirect measurement on a length measuring machine	KP 014
15	Check squares	Calibration – length 25 mm to 700 mm · CMC 44·L µm CMC for the field of measured quantity: Length	Direct measurement on a CMM	KP 010
16	Gauges and length measuring instruments, roundness and cylindricity gauges, straightness and flatness gauges, special fixtures and templates	Calibration – length 0 mm to 750 mm · CMC (7·L + 4,3) µm CMC for the field of measured quantity: Length	Direct measurement on a CMM	KP 016
17	Analogue protractors, special gauges and angle templates	Calibration – plane angle 0° to 360° · CMC 0,05° CMC for the field of measured quantity: Plane angle	Direct measurement on a CMM	KP 011
18	Digital protractors	Calibration – plane angle 0° to 360° · CMC 0,02° CMC for the field of measured quantity: Plane angle	Direct measurement on a CMM	KP 011
19	Torque wrenches and screwdrivers	Calibration – torque 0,2 Nm to 1000 Nm · CMC 0,6 % CMC for the field of measured quantity: Torque	Calibration with a standard torque device	KP 017

Reference standards (17)

KP 001

KP 002

KP 003

KP 004

KP 005

KP 006

KP 007

KP 008

KP 009

KP 010

KP 011

KP 012

KP 013

KP 014

KP 015

KP 016

KP 017

The same scope as data (JSON): https://labcoda.pl/api/accreditation-scopes/labs/CZ/2300