🔥 Hard coal — size analysis by manual dry or wet sieving: test sieves with apertures from 125 mm to 45 µm, fractions weighed to 0.1 %, sieving to constant mass (difference ≤ 0.2 %), rejection of the test for a loss or gain in mass above 1 %; PN-ISO 1953

Petrochemistry PN-ISO 1953

In short

Reference methods for the size analysis of hard coal by manual dry or wet sieving on test sieves with apertures from 125 mm to 45 µm. The test is performed according to PN-ISO 1953:1999 (Polish version; implements ISO 1953:1994 [IDT]); STATUS (PKN card as of 12.11.2026): PN-ISO 1953:1999 current (Polish version, published 04-06-1999); implements ISO 1953:1994, replaced PN-G-04532:1982; abroad the 2015 and 2025 editions. The procedure comprises 5 steps; it is used for: Hard coal — all types; not coke or other manufactured fuels (ISO 1953:1994, clause 1), Complete size analysis of run-of-mine coal or only the undersize in a graded product (note 8 to 6.1), Pulverized coal — only the percentage of oversize on the smallest sieve (clause 1).

At a glance

  • Standard: PN-ISO 1953:1999 (Polish version; implements ISO 1953:1994 [IDT])
  • Category: Petrochemistry
  • Procedure steps: 5
  • STATUS (PKN card as of 12.11.2026): PN-ISO 1953:1999 current (Polish version, published 04-06-1999); implements ISO 1953:1994, replaced PN-G-04532:1982; abroad the 2015 and 2025 editions
  • Sieves — condition (4.1.1, notes 1–2): apertures exclusively round or exclusively square (ISO 3310-1/-2); series 125–4 mm and 4 mm–45 µm; fraction ≤ 30 % of the mass, outermost sieves ≤ 5 %
  • Drying — condition (5.2): in air, at ambient temperature or ≤ 50 °C; ≤ 40 °C before caking or swelling tests

Overview

WHAT THE STANDARD COVERS. According to clause 1 of ISO 1953:1994 the standard gives reference methods for the size analysis of coal by manual sieving (dry or wet) on test sieves with aperture sizes from 125 mm to 45 µm; guidance on sampling is given in Annex A and notes on mechanical sieving in Annex B. It applies to all hard coals, not to coke or other manufactured fuels. For pulverized coal, a large part of which passes the smallest sieve, the methods give only the percentage of oversize.

ACCORDING TO THE TEXT OF ISO 1953:1994 — APPARATUS, PREPARATION, SIEVING, CALCULATION, TEST REPORT (clauses 1–8). We read the French version of ISO 1953:1994. Sieves (4.1.1): exclusively round-hole or exclusively square-hole, conforming to ISO 3310-1 or ISO 3310-2; recommended series 125, 90, 63, 45, 31.5, 22.4, 16, 11.2, 8, 5.6 and 4 mm (supplementary 100, 80, 50, 40, 25, 20, 12.5, 10 and 6.3 mm), for 4 mm and below — woven-wire sieves from 4 mm to 45 µm. In a complete analysis no fraction should exceed 30 % of the mass, the largest sieve should retain not more than 5 % and the smallest pass not more than 5 % (note 2). Balance to 0.1 % of the sample mass (4.1.3). Preparation (clause 5): air-drying at ambient temperature or at not more than 50 °C (40 °C if caking or swelling tests are to follow); division with a divider, and for pieces above 16.0 mm — by the strip or quartering method according to ISO 9411-1; wet coal below 4 mm — a cake of 15–25 mm, at least 50 increments, 2 kg. Dry sieving (6.2): above 45 mm — manual sieving and hand placing, free fall into the receiver not more than 150 mm; 4–45 mm — to-and-fro motion of up to 100 mm in each direction, another 8 movements in each direction (16 in total) after the last piece passes; below 4 mm — dedusting on the smallest sieve for 5 min (sieve inclined about 30°, 6–8 taps with the block, rotation through about 60°), 2 min for the dust to settle, the nest of sieves for 5 min with cleaning, the cycle three times, and then until the difference between successive weighings is not more than 0.2 % of the total mass. Wet sieving (6.3): portions of about 30 g washed with a water jet, drying as in 5.2, successive sieves; fines — flocculant, Büchner funnel, drying at 105–110 °C to constant mass. Calculation (7.1): fractions as % of the test portion mass, by fraction and cumulatively to 0.1 %; a loss or gain in mass is assigned to the smallest fraction, and above 1 % of the test portion mass the result is rejected. Graph (7.2): cumulative oversize against sieve aperture on a logarithmic or Rosin-Rammler scale, without extrapolation.

STATUS (PKN card as of 12.11.2026). The card for PN-ISO 1953:1999 (Polish version) has no withdrawal label: published 04-06-1999, 15 pages, KT 226 for Mechanical Coal Processing, "Implements: ISO 1953:1994 [IDT]", "Replaces: PN-G-04532:1982 - Polish version", ICS 73.040; the "Scope" field describes manual wet or dry sieving on sieves from 125 mm to 45 µm. In the iTeh catalogue SIST ISO 1953:1998 is withdrawn and replaced by SIST ISO 1953:2016; the iTeh search also lists ISO 1953:2015 and ISO 1953:2025 — we did not read these editions.

HOW MANY LABORATORIES AND IN WHAT FORM (accreditation scope database of the service, read 12.11.2026). The notation ISO 1953 appears in 5 records at 5 Polish laboratories: "PN-ISO 1953:1999" — AB 005, AB 103 and AB 300; "ISO 1953:2015 pkt. 6.2" — AB 081; "ISO 1953:2025" — AB 1980. Outside Poland — Czech laboratory 1078 (procedure IMP 1/LTH citing ČSN ISO 1953 among other standards).

WHAT THE LABORATORIES TEST (scope database, complete items — 5 Polish). Hard coal in all of them: size analysis of class (0.2–200.0) mm by the sieve method (AB 005), size composition of the fraction (1.0–200.0) mm (AB 300), content of the grain-size fraction (1–125) mm (AB 103), (3.0–40.0) mm (AB 081, only clause 6.2 — dry sieving) and size composition (3.0–50.0) mm (AB 1980); result range (0–100) %. The content of this page describes the 1994 edition, while AB 081 and AB 1980 cite the 2015 and 2025 editions, which we did not read.

WHERE AN APPARENTLY CORRECT RESULT IS EASY TO GET. Sieves: worn or damaged sieves cause serious errors — checking by the ISO 3310 methods (note 3); mixing round-hole and square-hole sieves. Preparation: drying above 50 °C (40 °C before caking tests), division that breaks pieces or loses dust. Sieving: too few movements after the last piece passes, an overloaded sieve (at most 75 % of the area covered during dedusting), no cycle to constant mass (≤ 0.2 %) for pieces below 4 mm. Result: a loss or gain in mass above 1 % — result to be rejected, not corrected; when the undersize is divided, the fractions are calculated against the mass of the undersize at the time of division.

WHAT WE DO NOT GIVE. Parts read: the iTeh sample of ISO 1953:1994 in French (clauses 1–8, Table 1 and figures only as a sketch) and the sample of SIST ISO 1953:1998 (English version, clauses 1–6.2.3.3). We do not give the content of Annexes A (sampling, Table A.1 — sample mass), B (mechanical sieving) and C (combined wet and dry sieving), nor the numbers of the example in Table 1 and Figures 1–2 — we did not read them. We did not examine differences between ISO 1953:1994 and the 2015 and 2025 editions.

Method principle

A coal sample (after air-drying at up to 50 °C and possible division) is sieved manually on test sieves with apertures from 125 mm to 45 µm — dry, and wet when the pieces tend to agglomerate (water jet, drying of the fractions, fines on a filter). Each fraction is weighed to 0.1 % and expressed as a percentage of the mass of the test portion, by fraction and cumulatively; a loss or gain in mass is assigned to the smallest fraction, and above 1 % the result is rejected.

Applications

Key parameters

ParameterValue
STATUS (PKN card as of 12.11.2026)PN-ISO 1953:1999 current (Polish version, published 04-06-1999); implements ISO 1953:1994, replaced PN-G-04532:1982; abroad the 2015 and 2025 editions
Sieves — condition (4.1.1, notes 1–2)apertures exclusively round or exclusively square (ISO 3310-1/-2); series 125–4 mm and 4 mm–45 µm; fraction ≤ 30 % of the mass, outermost sieves ≤ 5 %
Drying — condition (5.2)in air, at ambient temperature or ≤ 50 °C; ≤ 40 °C before caking or swelling tests
Division — condition (5.3–5.4)mechanical or riffle divider; pieces > 16.0 mm — strip or quartering (ISO 9411-1); wet coal < 4 mm — 50 increments, 2 kg
Dry sieving 4–45 mm (6.2.2)motion up to 100 mm in each direction; 8 movements in each direction (16) after the last piece passes
Dry sieving < 4 mm (6.2.3)dedusting 5 min (sieve inclined about 30°, 6–8 taps, rotation about 60°); nest of sieves 5 min × 3; then to a difference between weighings ≤ 0.2 % of the total mass
Wet sieving (6.3)portions of about 30 g; fines — flocculant, Büchner funnel, drying at 105–110 °C to constant mass
Result — calculation (7.1)% of the test portion mass, by fraction and cumulatively, to 0.1 %; loss/gain in the smallest fraction; > 1 % — result rejected
Coverage in accreditation scopes (database, read 12.11.2026)5 Polish laboratories (PN-ISO 1953:1999 — 3; ISO 1953:2015 — 1; ISO 1953:2025 — 1); 1 Czech

Standard

Standard number
PN-ISO 1953:1999 (Polish version; implements ISO 1953:1994 [IDT])
Title (PL)
Węgiel kamienny — Analiza ziarnowa metodą przesiewania
Title (EN)
Hard coal — Size analysis by sieving

Step-by-step procedure

  1. Sample preparation

    Air-drying (≤ 50 °C, ≤ 40 °C before caking tests); division first, then drying; pieces > 16.0 mm — strip or quartering; wet coal < 4 mm — cake of 15–25 mm, ≥ 50 increments, 2 kg (clause 5).

    🌡 Temperature: ≤ 50 °C

  2. Choice of method and sieves

    Dry for most coals, wet when pieces agglomerate; at least five apertures when the results are to be plotted; balance to 0.1 % (6.1, notes 6–10).

  3. Dry sieving

    Above 45 mm — manual sieving and hand placing; 4–45 mm — motion up to 100 mm, 16 movements after the last piece; below 4 mm — dedusting, nest of sieves 3 × 5 min with cleaning, then to a difference ≤ 0.2 % (6.2).

  4. Wet sieving

    Portions of about 30 g on the largest sieve under a water jet, checking the washings; drying the sieve as in 5.2, successive sieves; fines — flocculant, Büchner funnel, drying at 105–110 °C to constant mass (6.3).

    🌡 Temperature: 105–110 °C (fines)

  5. Result and test report

    Fractions as % of the test portion mass, by fraction and cumulatively to 0.1 %; loss or gain > 1 % — rejection; graph on a logarithmic or Rosin-Rammler scale without extrapolation; test report according to clause 8 (type of sieving, sieves, sample mass).

Required equipment and apparatus

EquipmentExampleIndicative price
Test sieves (4.1.1)Perforated plate (ISO 3310-2) or woven wire (ISO 3310-1), from 125 mm to 45 µm, with lids (4.2.1)—
Balance and receivers (4.1.2–4.1.3)Balance to 0.1 % of the sample mass; receivers for the material passing—
Trays and watch-glasses (4.1.4–4.1.5)Three smooth trays of non-corrodible material, at least 400 mm × 400 mm (or glazed paper); watch-glasses—
Accessories for dry sieving (4.2.2–4.2.4)Flat brush; hardwood block about 150 mm long, 10 mm × 10 mm cross-section; shovel or scoop—
Wet sieving (4.3)Büchner funnel, filtering flask, filter paper, oven controllable to ± 2 °C in the range 30–110 °C—

Reagents, media and consumables

ReagentCASDetails
Water—For washing in wet sieving — portions of about 30 g under a water jet (6.3.1)
Flocculating agent—Added to the final washings to settle the fines before filtration (6.3.4); the standard does not specify the type

Health and safety (OHS)

Frequently asked questions

Which standard describes this test?

The test is performed according to PN-ISO 1953:1999 (Polish version; implements ISO 1953:1994 [IDT]) — “Hard coal — Size analysis by sieving”.

How does this method work?

A coal sample (after air-drying at up to 50 °C and possible division) is sieved manually on test sieves with apertures from 125 mm to 45 µm — dry, and wet when the pieces tend to agglomerate (water jet, drying of the fractions, fines on a filter). Each fraction is weighed to 0.

What is the measuring range and accuracy?

STATUS (PKN card as of 12.11.2026): PN-ISO 1953:1999 current (Polish version, published 04-06-1999); implements ISO 1953:1994, replaced PN-G-04532:1982; abroad the 2015 and 2025 editions; Sieves — condition (4.1.1, notes 1–2): apertures exclusively round or exclusively square (ISO 3310-1/-2); series 125–4 mm and 4 mm–45 µm; fraction ≤ 30 % of the mass, outermost sieves ≤ 5 %; Drying — condition (5.2): in air, at ambient temperature or ≤ 50 °C; ≤ 40 °C before caking or swelling tests; Division — condition (5.3–5.4): mechanical or riffle divider; pieces > 16.0 mm — strip or quartering (ISO 9411-1); wet coal < 4 mm — 50 increments, 2 kg.

How long does the test take?

The procedure comprises 5 steps. The standard does not give a duration for every stage — the laboratory's own procedure decides.

What equipment is required?

Test sieves (4.1.1), Balance and receivers (4.1.2–4.1.3), Trays and watch-glasses (4.1.4–4.1.5), Accessories for dry sieving (4.2.2–4.2.4), Wet sieving (4.3).

Where is this test used?

Hard coal — all types; not coke or other manufactured fuels (ISO 1953:1994, clause 1); Complete size analysis of run-of-mine coal or only the undersize in a graded product (note 8 to 6.1); Pulverized coal — only the percentage of oversize on the smallest sieve (clause 1); In accreditation scopes: 5 Polish laboratories — hard coal, fractions from 0.2 mm to 200 mm.

What safety precautions apply?

The standard contains no separate safety warning in the text read; dry sieving of pieces below 4 mm is carried out under a lid, and after 5 min 2 min are allowed for the dust to settle (6.2.3.2–6.2.3.4); TECHNICAL NOTE: in wet sieving too strong a water jet disintegrates shale — the standard requires agglomerated pieces to be broken up carefully (6.3.1).

Which laboratory can perform this test?

The test is performed by laboratories accredited to ISO/IEC 17025. On LabCoda you can find them by the standard number PN-ISO 1953.

🔍 Find a laboratory performing this test