📏 Hand torque tools (wrenches and screwdrivers) — indicating Type I and setting Type II, classes A–G: design and quality conformance testing, maximum permissible relative deviation ±4 % / ±6 %, overloading test 125 %, endurance test 5 000 cycles, declaration of conformance; PN-EN ISO 6789-1

Metrology PN-EN ISO 6789-1

In short

Requirements and methods for conformance testing and marking of hand torque tools used for controlled tightening of screws and nuts, together with minimum requirements for the declaration of conformance. The test is performed according to PN-EN ISO 6789-1:2017-03 (English version; implements EN ISO 6789-1:2017 and ISO 6789-1:2017 [IDT]); STATUS (PKN card, 16.11.2026): PN-EN ISO 6789-1:2017-03 (English version, published 30-03-2017); implements EN ISO 6789-1:2017 and ISO 6789-1:2017; replaces PN-EN ISO 6789:2009. The procedure comprises 5 steps; it is used for: Hand torque wrenches and screwdrivers, indicating (Type I, classes A–E) and setting (Type II, classes A–G), for controlled tightening of screws and nuts (ISO 6789-1:2017, clauses 1 and 4), Design conformance testing by the manufacturer and the declaration of conformance (5.1, clause 8), Basis of the measurement method in the calibration of tools according to ISO 6789-2 (clause 6 of part 1).

At a glance

  • Standard: PN-EN ISO 6789-1:2017-03 (English version; implements EN ISO 6789-1:2017 and ISO 6789-1:2017 [IDT])
  • Category: Metrology
  • Procedure steps: 5
  • STATUS (PKN card, 16.11.2026): PN-EN ISO 6789-1:2017-03 (English version, published 30-03-2017); implements EN ISO 6789-1:2017 and ISO 6789-1:2017; replaces PN-EN ISO 6789:2009
  • Types and classes (clause 4): Type I (indicating): A–E; Type II (setting): A–G
  • Maximum torque — square drive (table 2): 6,3 — 30 N·m; 10 — 135 N·m; 12,5 — 340 N·m; 20 — 1 000 N·m; 25 — 2 100 N·m

Overview

WHAT THE STANDARD COVERS. According to clause 1 of ISO 6789-1:2017 the document specifies the conformance testing and marking requirements for hand torque tools used for controlled tightening of screws and nuts, and the minimum requirements for the declaration of conformance of these tools. It applies to indicating (Type I) and setting (Type II) torque tools; the tools covered are those identified in ISO 1703:2005 by reference numbers 6 1 00 11 0, 6 1 00 11 1, 6 1 00 12 0, 6 1 00 12 1, 6 1 00 14 0 and 6 1 00 15 0. The standard does not specify requirements for calibration certificates — these are given in ISO 6789-2. The PKN card of PN-EN ISO 6789-1:2017-03 gives the same scope.

ACCORDING TO THE TEXT OF ISO 6789-1:2017 (publisher's sample in English: foreword, introduction, clauses 1–5.1.8; in French — the table of contents and the same clauses). The standard was prepared by ISO/TC 29 (Small tools), subcommittee SC 10. The first edition of ISO 6789-1 together with ISO 6789-2 replaced ISO 6789:2003 after technical revision: the standard was divided into two parts (part 1 — design and manufacture including the content of the declaration of conformance, part 2 — traceable calibration certificates with a method of uncertainty calculation and calibration of the torque measurement device), the designation of output drives was extended to hexagonal and other drives, the definition of the torque range was changed, the loading speed (time to reach the last 20 %) was changed, the avoidance of parasitic forces was emphasized, flow charts of the measurement sequence were added (annex C) and the requirement of a declaration of conformance was added. Normative references: ISO 1173, ISO 1174-1, ISO 6789-2:2017 and ISO/IEC 17025. Definitions (3.1): design conformance testing and quality conformance testing (during design or modification and during manufacture), declaration of conformance (documented information from the manufacturer), maximum permissible deviation (maximum relative deviation of the torque value observed on the torque measurement device, as a percentage of the target value on the tool; not “accuracy” nor the measurement error of ISO 6789-2), torque measurement system (torque measurement device and loading system — the standard for the tool), torque measurement device (working standard, mechanical or with an electronic transducer and display), indicating torque tool Type I (indicates the torque on a scale, dial or display), setting torque tool Type II (signals the reaching of the pre-set value by a physical impulse, with or without an audible signal, with a temporary reduction of torque), adjustable graduated (Type II classes A, D, G), adjustable non-graduated (Type II classes C, F) and fixed setting (Type II classes B, E). Symbols: a_d — relative deviation from the target torque (%), X_t — target value (indicated, set, nominal; N·m), X_o — value observed on the torque measurement device (N·m).

CLASSIFICATION (clause 4). Type I (indicating, annex A): class A — wrench with torsion or flexion bar; B — wrench with rigid housing and scale, dial or display; C — wrench with rigid housing and electronic measurement; D — screwdriver with scale, dial or display; E — screwdriver with electronic measurement. Type II (setting, annex B): A — adjustable wrench, graduated or with display; B — fixed-setting wrench; C — adjustable non-graduated wrench; D — adjustable screwdriver, graduated or with display; E — fixed-setting screwdriver; F — adjustable non-graduated screwdriver; G — flexion-bar wrench, adjustable, graduated.

DESIGN CONFORMANCE TESTING (5.1). The manufacturer verifies conformance with 5.1.2–5.1.8. Maximum torques (table 2): square drive 6,3 — 30 N·m, 10 — 135 N·m, 12,5 — 340 N·m, 20 — 1 000 N·m, 25 — 2 100 N·m; hexagonal drive 3 — 4 N·m, 4 — 10 N·m, 5,5 — 25 N·m, 6,3 — 30 N·m, 8 — 70 N·m, 11,2 — 200 N·m, 12,5 — 340 N·m (dimensions according to ISO 1174-1 and ISO 1173). Torque range: Type I classes A, B, D and Type II classes A, D, G — from the lowest marked value to 100 % of the maximum torque; Type I classes C, E and Type II classes B, C, E, F — as specified by the manufacturer. Scales and dials: graduation increment not exceeding 5 % of the maximum torque; electronic displays: resolution not exceeding 1/4 of the maximum permissible relative deviation at each target value; the range from zero to the lowest value shall be marked as outside the specified range. Maximum permissible relative deviation (tables 3 and 4): Type I classes A and D — ±6 %; Type I classes B, C, E — ±6 % up to 10 N·m and ±4 % above 10 N·m; Type II classes A, B, C — ±6 % up to 10 N·m and ±4 % above; Type II classes D, E, F, G — ±6 %; a tool operating in both directions shall meet the requirement in each direction specified by the manufacturer, and a smaller deviation claimed by the manufacturer applies instead of the table value; the uncertainty of the tool and of the torque measurement device is not considered when determining conformance. Overloading test (5.1.6): loading three times in each direction of operation to a torque not less than 125 % of the maximum torque (or the nominal capacity for Type II classes D, E, F); Type II classes A, C, D, F, G after setting to 100 % of the maximum torque; not applicable to limiting torque tools; afterwards the tool shall be within the permissible deviation and free from damage. Endurance test (5.1.7): 5 000 cycles in each direction of operation of the mechanism at the maximum torque (Type II classes B, E — the nominal pre-set torque) at a rate of 5–20 cycles/min; afterwards — within the permissible deviation and free from damage. Effect of geometric changes (5.1.8): the influence of, for example, flexible-head ratchets and extension bars on the output torque is tested, and the manufacturer communicates it to users in the instruction sheet or the declaration of conformance. Further clauses according to the table of contents: quality conformance testing (5.2), conformance during use, torque measurement — torque measurement system, application of torque, ambient conditions, measurement requirements, measurement sequence for Types I and II (clause 6), calculation of the deviation with two examples (clause 7), declaration of conformance (clause 8) and marking (clause 9); the sample does not contain their text.

STATUS (PKN card, read 16.11.2026). PN-EN ISO 6789-1:2017-03 — English version, Polish title “Narzędzia montażowe do wkrętów i nakrętek -- Ręczne narzędzia dynamometryczne -- Część 1: Wymagania i metody badań dotyczące zgodności projektu i jakości wyrobu: minimalne wymagania dotyczące deklaracji zgodności”, published 30-03-2017, 36 pages, KT 236 for Fasteners and Assembly Tools, implements EN ISO 6789-1:2017 and ISO 6789-1:2017 [IDT], replaces PN-EN ISO 6789:2009 (Polish version); the card gives no withdrawal date. iTeh catalogue (16.11.2026): ISO 6789-1:2017 — stage “International Standard to be revised” (90.92); European draft prEN ISO 6789-1 — stage “closure of enquiry” (40.60), planned publication 24-11-2026.

IN ACCREDITATION SCOPES (scope database of the service, read 16.11.2026, after loading the scopes of this batch). PN-EN ISO 6789-1 appears at 9 Polish calibration laboratories (14 records) — in the 2017 or 2017-03 edition, most often together with PN-EN ISO 6789-2:2017 (two records alongside BS 7882) — and at 2 Czech laboratories (3 records).

Method principle

The torque tool is compared with a torque measurement system: for a target value X_t (indicated, set or nominal) the value X_o is read on the torque measurement device and the relative deviation a_d is calculated. Each result shall lie within the maximum permissible relative deviation for the type and class of the tool (±4 % or ±6 %). Design conformance is further confirmed by the overloading test (3 × 125 % of the maximum torque), the endurance test (5 000 cycles in each direction) and the test of the effect of geometric changes.

Applications

Key parameters

ParameterValue
STATUS (PKN card, 16.11.2026)PN-EN ISO 6789-1:2017-03 (English version, published 30-03-2017); implements EN ISO 6789-1:2017 and ISO 6789-1:2017; replaces PN-EN ISO 6789:2009
Types and classes (clause 4)Type I (indicating): A–E; Type II (setting): A–G
Maximum torque — square drive (table 2)6,3 — 30 N·m; 10 — 135 N·m; 12,5 — 340 N·m; 20 — 1 000 N·m; 25 — 2 100 N·m
Maximum torque — hexagonal drive (table 2)3 — 4; 4 — 10; 5,5 — 25; 6,3 — 30; 8 — 70; 11,2 — 200; 12,5 — 340 N·m
Scale and display (5.1.4)increment ≤ 5 % of the maximum torque; display resolution ≤ 1/4 of the permissible deviation
Permissible deviation, Type I (table 3)classes A, D: ±6 %; classes B, C, E: ±6 % (≤ 10 N·m), ±4 % (> 10 N·m)
Permissible deviation, Type II (table 4)classes A, B, C: ±6 % (≤ 10 N·m), ±4 % (> 10 N·m); classes D, E, F, G: ±6 %
Overloading test (5.1.6)3 times in each direction, ≥ 125 % of the maximum torque (Type II D, E, F — nominal capacity)
Endurance test (5.1.7)5 000 cycles in each direction, 5–20 cycles/min
Coverage in accreditation scopes (read 16.11.2026)9 Polish calibration laboratories (14 records); 2 Czech (3 records)

Standard

Standard number
PN-EN ISO 6789-1:2017-03 (English version; implements EN ISO 6789-1:2017 and ISO 6789-1:2017 [IDT])
Title (PL)
Narzędzia montażowe do wkrętów i nakrętek — Ręczne narzędzia dynamometryczne — Część 1: Wymagania i metody badań dotyczące zgodności projektu i jakości wyrobu: minimalne wymagania dotyczące deklaracji zgodności
Title (EN)
Assembly tools for screws and nuts — Hand torque tools — Part 1: Requirements and methods for design conformance testing and quality conformance testing: minimum requirements for declaration of conformance

Step-by-step procedure

  1. Classification and range

    Determination of the type and class of the tool (clause 4), the torque range and the conformity of the output drive size with the maximum torque according to table 2 (5.1.2–5.1.3).

  2. Scale and display

    Check of the graduation increment (≤ 5 % of the maximum torque) or of the display resolution (≤ 1/4 of the permissible deviation) and of the marking of the range below the lowest value (5.1.4).

  3. Relative deviation

    Measurement according to clause 6 and calculation according to clause 7; each result within table 3 or 4 or a smaller value claimed by the manufacturer, without considering uncertainty (5.1.5).

  4. Overloading and endurance

    Three loadings ≥ 125 % in each direction, then 5 000 cycles in each direction at 5–20 cycles/min; after each test a renewed check of the deviation and a visual inspection (5.1.6–5.1.7).

  5. Effect of geometry and declaration

    Test of the influence of flexible heads and extension bars on the output torque and communication of the result in the instruction sheet or the declaration of conformance (5.1.8, clause 8).

Required equipment and apparatus

EquipmentExampleIndicative price
Torque measurement system (3.1.5)Torque measurement device with a loading system — the standard for the tool; a calibration system according to ISO 6789-2 may be used—
Torque measurement device (3.1.6)Working standard, mechanical or with an electronic torque transducer and display—
Rig for the overloading and endurance tests (5.1.6–5.1.7)Loading ≥ 125 % of the maximum torque; 5 000 cycles at a rate of 5–20 cycles/min—

Frequently asked questions

Which standard describes this test?

The test is performed according to PN-EN ISO 6789-1:2017-03 (English version; implements EN ISO 6789-1:2017 and ISO 6789-1:2017 [IDT]) — “Assembly tools for screws and nuts — Hand torque tools — Part 1: Requirements and methods for design conformance testing and quality conformance testing: minimum requirements for declaration of conformance”.

How does this method work?

The torque tool is compared with a torque measurement system: for a target value X_t (indicated, set or nominal) the value X_o is read on the torque measurement device and the relative deviation a_d is calculated. Each result shall lie within the maximum permissible relative deviation for the type and class of the tool (±4 % or ±6 %).

What is the measuring range and accuracy?

STATUS (PKN card, 16.11.2026): PN-EN ISO 6789-1:2017-03 (English version, published 30-03-2017); implements EN ISO 6789-1:2017 and ISO 6789-1:2017; replaces PN-EN ISO 6789:2009; Types and classes (clause 4): Type I (indicating): A–E; Type II (setting): A–G; Maximum torque — square drive (table 2): 6,3 — 30 N·m; 10 — 135 N·m; 12,5 — 340 N·m; 20 — 1 000 N·m; 25 — 2 100 N·m; Maximum torque — hexagonal drive (table 2): 3 — 4; 4 — 10; 5,5 — 25; 6,3 — 30; 8 — 70; 11,2 — 200; 12,5 — 340 N·m.

How long does the test take?

The procedure comprises 5 steps. The standard does not give a duration for every stage — the laboratory's own procedure decides.

What equipment is required?

Torque measurement system (3.1.5), Torque measurement device (3.1.6), Rig for the overloading and endurance tests (5.1.6–5.1.7).

Where is this test used?

Hand torque wrenches and screwdrivers, indicating (Type I, classes A–E) and setting (Type II, classes A–G), for controlled tightening of screws and nuts (ISO 6789-1:2017, clauses 1 and 4); Design conformance testing by the manufacturer and the declaration of conformance (5.1, clause 8); Basis of the measurement method in the calibration of tools according to ISO 6789-2 (clause 6 of part 1); In accreditation scopes: 9 Polish calibration laboratories and 2 Czech.

Which laboratory can perform this test?

The test is performed by laboratories accredited to ISO/IEC 17025. On LabCoda you can find them by the standard number PN-EN ISO 6789-1.

🔍 Find a laboratory performing this test