🔩 Metallic wire of diameter or thickness 0.3–10 mm — simple torsion test: twisting a length of wire around its own axis with one grip until fracture or a specified number of turns, free length 200 d, 100 d or 50 d, tension up to 2 % of the nominal tensile strength, speed according to Table 3, result — number of complete turns; PN-ISO 7800

Materials and NDT PN-ISO 7800

In short

Determination of the ability of metallic wire to undergo plastic deformation during torsion in one direction. The test is performed according to PN-ISO 7800:1996 (Polish version; implements ISO 7800:1984 [IDT]); Diameter range — condition (clause 1): d or D from 0.3 to 10 mm inclusive. The procedure comprises 5 steps; it is used for: Round and non-circular metallic wire of diameter or characteristic dimension 0.3–10 mm (ISO 7800:1984, clause 1), Replaced in PN the standard PN-M-80003:1983 (PKN card), Steel, copper and copper alloys, aluminium and aluminium alloys — separate speeds in Table 3.

At a glance

  • Standard: PN-ISO 7800:1996 (Polish version; implements ISO 7800:1984 [IDT])
  • Category: Materials and NDT
  • Procedure steps: 5
  • STATUS (PKN card as of 11.11.2026): PN-ISO 7800:1996 current (Polish version); implements ISO 7800:1984, which has the status "Withdrawn" in the iTeh catalogue; replaced PN-M-80003:1983
  • Diameter range — condition (clause 1): d or D from 0.3 to 10 mm inclusive
  • Free length — condition (Table 2): 0.3 ≤ d < 1 mm: 200 d; 1 ≤ d < 5 mm: 100 d (by agreement 50 d); 5 mm ≤ d: 50 d (by agreement 30 d)

Overview

WHAT THE STANDARD COVERS. According to clause 1 of ISO 7800:1984 the standard specifies the method for determining the ability of metallic wire of diameter or thickness 0.3 to 10 mm inclusive to undergo plastic deformation during simple torsion in one direction. Principle (clause 2): the test consists of twisting a test piece of wire around its own axis in one direction.

ACCORDING TO THE TEXT OF ISO 7800:1984 — SYMBOLS, MACHINE, TEST PIECE, PROCEDURE, TEST REPORT (foreword, clauses 1–7, Tables 1–3, figure). The standard was prepared by ISO/TC 164 (Mechanical testing of metals); first edition 1984-03-15; it replaced ISO 136-1972, ISO 2627-1973 and ISO Recommendation R 957-1969. Symbols (Table 1): d — diameter of a round wire, mm; D — characteristic dimension of non-circular wires (maximum dimension of the cross-section, usually given in the product standard), mm; L — free length between grips, mm; Nt — number of turns. Machine (clause 4): grips of sufficient hardness, arranged so that during testing they remain on the same axis and do not apply any bending force to the test piece; the machine must not prevent a change of length of the test piece between the grips; one grip rotates around the axis of the test piece, the other is not subject to any angular deflection (except as necessary to measure the torque); the distance between the grips is adjustable; an appropriate tensile stress can be applied. Test piece (clause 5): a length of wire as straight as possible; straightening by hand or, if not possible, by hammering on a level surface of wood, plastic material or copper with a hammer of similar material; without damaging the surface and without twisting; wire with a localized sharp curvature shall not be straightened. Free length (Table 2, unless otherwise specified): 0.3 ≤ d < 1 mm — 200 d; 1 ≤ d < 5 mm — 100 d (by special agreement 50 d when the machine will not permit 100 d); 5 mm ≤ d — 50 d (by special agreement 30 d when the machine will not permit 50 d); for non-circular wire D instead of d. Procedure (clause 6): in general at ambient temperature between 10 and 35 °C, under controlled conditions at 23 ± 5 °C; the axis of the test piece coincides with the axis of the grips and the test piece stays straight during the test — unless otherwise specified, by a constant tensile stress just sufficient to straighten it, not exceeding 2 % of the nominal tensile strength of the wire; one grip is rotated at a reasonable constant speed until the test piece breaks or a specified number of turns is reached; the complete turns imparted to the wire by the rotating grip are counted. Speed (Table 3, unless the product standard specifies otherwise) — maximum number of turns per second: steel — 3 (d < 1 mm), 1 (1 ≤ d < 5.0 mm), 0.5 (5.0 ≤ d ≤ 10.0 mm); copper and copper alloys — 5 (d < 1), 2 (1 ≤ d < 1.5), 1.5 (1.5 ≤ d < 3.0), 1 (3.0 ≤ d < 5.0), 0.5 (5.0 ≤ d ≤ 10.0); aluminium and aluminium alloys — 1 over the whole range. Assessment (6.5): if the number of turns meets the requirement of the product standard, the test piece passes irrespective of the position of failure; if not, and the failure is within 2 d of the grips, the test is invalid and shall be repeated. Test report (clause 7): reference to the standard; identification of the test piece (material, cast number, etc.); d or D; test piece preparation (method of straightening, etc.); test conditions (e.g. free length, applied tensile stress); result.

STATUS (PKN card as of 11.11.2026). The card for PN-ISO 7800:1996 (Polish version) has no withdrawal label: published 05-02-1996, 7 pages, KT 163 for Ropes and Rope Transport, "Implements: ISO 7800:1984 [IDT]", "Replaces: PN-M-80003:1983 - Polish version", ICS 77.140.65; "Scope" field: "The scope of the standard, the requirements for machines for simple torsion tests, the method of taking and preparing test pieces, the conditions and method of carrying out the test, and the requirements for the test report are specified". The PKN search (term "PN-ISO 7800", 11.11.2026) returns only this card. iTeh catalogue (read 11.11.2026): ISO 7800:1984 and ISO 7800:2003 — status "Withdrawn"; the catalogue also has a card for ISO 7800:2012 (we did not read its status); the Slovenian SIST ISO 7800:1996 — withdrawn 29-01-2015. The content of this description comes from ISO 7800:1984, implemented by PN-ISO 7800:1996 — we have not read the newer ISO editions.

HOW MANY LABORATORIES AND IN WHAT FORM (accreditation scope database of the service, read 11.11.2026). The notation "PN-ISO 7800:1996" appears in 5 records at 5 Polish laboratories: AB 005, AB 273, AB 771, AB 1141 and AB 1348. Outside Poland — 2 records at 2 Czech laboratories (1322: alongside ČSN 02 4301:1974; 1609: procedure PPo CZ-10/333 citing ČSN ISO 7800). We have not compared the current PCA scope documents of these laboratories with the database.

WHAT THE LABORATORIES TEST (scope database, complete items — 5 Polish). AB 1141 — wire of diameter 0.3 to 5.0 mm: resistance to plastic deformation, number of turns. AB 005 — wires: resistance to plastic deformation, diameter (1–3.5) mm. AB 771 — wires: resistance to plastic deformation, diameters up to 5.0 mm. AB 1348 — wires: resistance to simple torsion. AB 273 — brushes (rotary, hand, chimney sweeping brushes, special): resistance of metallic wire of diameter or thickness (0.3–10.0) mm to simple torsion.

WHERE AN APPARENTLY CORRECT RESULT IS EASY TO GET. Test piece: wire damaged or twisted during straightening, straightening with a metal hammer on steel, straightening a localized sharp bend — these are conditions other than in clause 5. Set-up: grips not on the same axis or bending the test piece; a machine preventing the wire from shortening; too high a tension (over 2 % of the nominal tensile strength) or none — the wire is not straight. Free length other than in Table 2 without agreement; for non-circular wire calculated from D. Speed higher than in Table 3 for the given metal and diameter. Counting: complete turns of the grip only. Assessment: a fracture at the grip (within 2 d) with a result below the requirement is not a result — the test is repeated. The required number of turns is given by the product standard, not by ISO 7800.

WHAT WE DO NOT GIVE. Parts read: the iTeh sample of SIST ISO 7800:1996 (ISO 7800:1984 in English: foreword, clauses 1–7, Tables 1–3 and figure — the tables read from the page image). We do not give the content of ISO 7800:2003 or ISO 7800:2012 — we have not read them. The standard does not give required numbers of turns for particular wires — product standards give them.

Method principle

A length of wire (d or D from 0.3 to 10 mm) held in two grips on a common axis, with a free length of 200 d, 100 d or 50 d (Table 2) and a straightening tension not exceeding 2 % of the nominal tensile strength, is twisted around its own axis by rotating one grip at a constant speed not exceeding Table 3 (e.g. steel 3, 1 or 0.5 turns/s) until fracture or a specified number of turns; the complete turns are counted and the test is assessed against the requirement of the product standard (ISO 7800:1984, clauses 2–6).

Applications

Key parameters

ParameterValue
STATUS (PKN card as of 11.11.2026)PN-ISO 7800:1996 current (Polish version); implements ISO 7800:1984, which has the status "Withdrawn" in the iTeh catalogue; replaced PN-M-80003:1983
Diameter range — condition (clause 1)d or D from 0.3 to 10 mm inclusive
Free length — condition (Table 2)0.3 ≤ d < 1 mm: 200 d; 1 ≤ d < 5 mm: 100 d (by agreement 50 d); 5 mm ≤ d: 50 d (by agreement 30 d)
Temperature — condition (6.1)ambient 10–35 °C; under controlled conditions 23 ± 5 °C
Straightening tension — condition (6.2)constant, just sufficient to straighten, ≤ 2 % of the nominal tensile strength
Speed — steel (Table 3)at most 3 turns/s (d < 1 mm), 1 (1–5 mm), 0.5 (5–10 mm)
Speed — copper and alloys / aluminium (Table 3)copper: 5, 2, 1.5, 1, 0.5 turns/s according to diameter; aluminium: 1 turn/s
Assessment — condition (6.5)result ≥ requirement — passed irrespective of the position of failure; result below and failure within 2 d of the grip — test invalid, repeat
Coverage in accreditation scopes (database, read 11.11.2026)5 Polish laboratories, 5 records; 2 Czech laboratories

Standard

Standard number
PN-ISO 7800:1996 (Polish version; implements ISO 7800:1984 [IDT])
Title (PL)
Metale — Drut — Próba jednokierunkowego skręcania
Title (EN)
Metallic materials — Wire — Simple torsion test

Step-by-step procedure

  1. Test piece

    A length of wire as straight as possible; straightening by hand or with a hammer of wood, plastic or copper, without damage or twisting; a localized sharp bend is not straightened (clause 5).

  2. Free length

    According to Table 2: 200 d, 100 d or 50 d (by agreement 50 d or 30 d); for non-circular wire D.

  3. Mounting

    Axis of the test piece in the axis of the grips; straightening tension ≤ 2 % of the nominal tensile strength; temperature 10–35 °C (controlled 23 ± 5 °C) (6.1–6.2).

    🌡 Temperature: 10–35 °C

  4. Twisting

    Rotation of one grip at a constant speed ≤ Table 3 until fracture or a specified number of turns; counting of complete turns (6.3–6.4).

  5. Assessment and test report

    Against the requirement of the product standard; fracture within 2 d of the grip with a result below the requirement — repetition (6.5); report according to clause 7. PN-ISO 7800:1996 — current (PKN card as of 11.11.2026).

Required equipment and apparatus

EquipmentExampleIndicative price
Torsion testing machine (4.1–4.5)Hard grips on a common axis without bending the test piece; one rotating, the other fixed (except for deflection to measure torque); free change of length; adjustable distance; application of tensile stress—
Turn counterNumber of complete turns imparted to the wire by the rotating grip (6.3)—
Hammer and support for straightening (5.2)Wood, plastic or copper — hammer and level surface of a similar material—

Health and safety (OHS)

Frequently asked questions

Which standard describes this test?

The test is performed according to PN-ISO 7800:1996 (Polish version; implements ISO 7800:1984 [IDT]) — “Metallic materials — Wire — Simple torsion test”.

How does this method work?

A length of wire (d or D from 0.3 to 10 mm) held in two grips on a common axis, with a free length of 200 d, 100 d or 50 d (Table 2) and a straightening tension not exceeding 2 % of the nominal tensile strength, is twisted around its own axis by rotating one grip at a constant speed not exceeding Table 3 (e.

What is the measuring range and accuracy?

STATUS (PKN card as of 11.11.2026): PN-ISO 7800:1996 current (Polish version); implements ISO 7800:1984, which has the status "Withdrawn" in the iTeh catalogue; replaced PN-M-80003:1983; Diameter range — condition (clause 1): d or D from 0.3 to 10 mm inclusive; Free length — condition (Table 2): 0.3 ≤ d < 1 mm: 200 d; 1 ≤ d < 5 mm: 100 d (by agreement 50 d); 5 mm ≤ d: 50 d (by agreement 30 d); Temperature — condition (6.1): ambient 10–35 °C; under controlled conditions 23 ± 5 °C.

How long does the test take?

The procedure comprises 5 steps. The standard does not give a duration for every stage — the laboratory's own procedure decides.

What equipment is required?

Torsion testing machine (4.1–4.5), Turn counter, Hammer and support for straightening (5.2).

Where is this test used?

Round and non-circular metallic wire of diameter or characteristic dimension 0.3–10 mm (ISO 7800:1984, clause 1); Replaced in PN the standard PN-M-80003:1983 (PKN card); Steel, copper and copper alloys, aluminium and aluminium alloys — separate speeds in Table 3; Assessment of the ability to undergo plastic deformation against the requirements of product standards (6.5); In accreditation scopes: 5 Polish laboratories — wires up to 5 mm and brush wires (0.3–10 mm).

What safety precautions apply?

Fracture of the twisted wire — sharp ends and springback; guard around the grips, safety glasses; The part of the standard read gives no hazards of the test — NOT GIVEN; TECHNICAL NOTE: the required number of turns is given by the product standard; with a fracture at the grip (within 2 d) and a result below the requirement the test is repeated.

Which laboratory can perform this test?

The test is performed by laboratories accredited to ISO/IEC 17025. On LabCoda you can find them by the standard number PN-ISO 7800.

🔍 Find a laboratory performing this test